Fully Automatic Washing Machine User manual
This manual is for
HWMP55-918
Please read this manual
carefully before using.
Retain it for future
Parts
Cold water valve
Hot water valve
Top lid
Screw cover
Handle
Detergent box
Control pannel
Lint filter
Power cord
Balance ring
Inner tub
Pulsater
Back
cover
Front control
board
Cabinet
Fixed leg
(2 pieces)
Drain connector
Drain hose
Adjustable leg
(2pieces)
Back cover
Instruction for adjustable leg
(2pieces)
Meaning and description of symbols
Contents marked with this symbol are related to the
safety of the product and the personal safety of the
users. Please operate in strict conformity to the
contents, otherwise it may cause damage of the
machine or injure the personal safety of the user.
Warning sign
Contents marked with this symbol are actions forbidden.
Performing of those actions may result in damage of
the machine or injure the personal safety of the user.
Forbidden sign
Please check if power point has been earthed
condition before using to guarantee your safety
1
Safety precautions
After installation of the washing
A separate earthed socket is required
for the power supply.Hold the plug
not the electric cable when
unplugging the washing machine.
Do not insert or remove the power
plug with wet hands.
machine, the power plug should
be accessible. Ensure the plug is
removed and the taps turned off
in the following cases:power
failure, cleaning, moving,
installation and when not in use.
a
Do not block the ventilation holes with
carpet Ensure carpet does not obstruct
the apening in the base
The ventilation
holes at the bottom
Soft object
Back
Front
Safety precautions
3
Installation and adjustment
Please install and adjust the machine according to the requirement of
the manual. It is very important to your safety and the correct
operating the machine.
Install the lint filter
After opening the package, please take out the lint
filter from the document bag, install it to the inner
tub. See the figure opposite.
Inner tub
Please ensure the lint filter is installed correctly and in
good condition to ensure the water outlet is not blocked
or the flow altered. If the lint filter is lost please contact
the local after -sales service department.
Lint filter
Install the bottom plate
The purpose of the bottom plate is to block noise
Back
and give a quiet performance from the washing
machine during operation.
Steps:
Front
1. Lay the washer on its back.
2. Place the plate on to the bottom of the machine.
Bottom plate
3.Use a screwdriver to tighten the screws securing
the panel to bottom of the washer.
Soft object
Screw
4.Once all screws are tight and the panel is secure return
the washer to its standing position.
Adjust the position
The largest allowable slope of the base of the machine is 2
.
Slanting or rough ground will result in unstable running or stoppage of the
machine. Please adjust it by the following method:
Confirm it is level
2
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first
lift up the side of the leg slightly, loosen
the adjustable nut, and twist the leg.
adjustable nut
Fasten
Loosen
High
Adjustable
feet
2 . After adjustment, fasten the nut.
Low
4
Install the drain hose
Install the drain hose
First install the drain hose hook on the part of
outer drain hose component.
Put the drain hose clamp on the outer drain hose,
Insert the outer drain hose into the joint for it, and
then clutch tightly with drain hose hoop.
Drain hose neck
Drain hose hoop
Drain hose joint
4-4.Usage of the drain hose
Ensure the drain hose is mounted at a suitable height.
(Between 800-1200mm above the floor).
Do not push it too far down the drain pipe or siphoning will occur.
0.8m
h
1.2m
5
Install the water inlet hose
Install the water inlet hose
Use the new hose supplied, do not reuse old hoses.
1. Insert a new flat washer into each end of the inlet hose. Firmly put the
washers in the coupling.
Note:
Use the new hose supplied with the washer.
Any other old hoses should not be used.
You may have to use pliers to tighten the coupling.
Do not overtighten because you may cause
damage to the valve.
2. Connect the water inlet hose to the water faucet.
3. Connect the other ends to their respective cold and hot water inlet valve
located at the rear of the washer
Nut of the water inlet hose
Water absorption cushion
to Joiner of the water inlet valve
4.Fasten the nut. Swing the hose gently to confirm that the hose is
securely fastened.
Check the connection between the
water inlet hose and the water tap
1.Swing the hose gently to confirm that the hose
is securely fastened.
2.After installation, open the tap to check for leaks..
3.Do not bend the hose unduly.
4.Before every use check the hose connections are
firm at both ends. This is to ensure the connections
remain firm over time.
Remove the water inlet hose
1.Close the water tap.
2. Remove the water inlet hose from the water tap and washer.
6
1.Preparation before washing
Preparation before washing
Preparation before washing
1. Connect the water inlet hose.
2. Inset the power plug into the electrical socket.
3. Ensure the drain hose is mounted at the correct height.
4. Select a suitable location for the washer on a hard, even
surface away from direct sunlight or heat sources, e.g.
radiators, cooking
appliances etc.
5. Any floor unevenness may
0.8m
H
1.2m
result in unstable working
or abnormal noise. Please
ensure the machine is level.
Check the following before washing
When the machine
is running buttons
may cause noise.
To reduce the noise
turn clothes inside
out or place them in
a laundry bag.
Clear the
Check if the
laundry has
any special
washing
The weight of
Tie any long
strips, fasten
buttons and
close zippers.
pockets. Take
out loose items
such as coins,
sand, hairpins
etc.
the laundry shall
not exceed the
rated capacity.
Loosen the laundry
before placing it
evenly in the tub.
instructions
a. Check if the laundry is suitable for machine washing.
b. Divide the laundry into colour fast and non-colour fast items.
c. Place items that do not absorb water easily into the water by hand.
d. For heavily soiled items, please first remove loose dirt, then apply detergent
directly to the stain before washing.
e. For those items that may get lint or are furry or fluffy, please turn them inside out
before washing
f . Do not put laundry polluted by chemicals into the washing machine.
7
2.Load the laundry
The rated washing capacity refers to the largest dry weight of a
load that can be washed.
The thickness, size and type of clothes will influence the actual
capacity. Be careful to only load a reasonable amount of laundry.
Do not select more than
4
water level for clothes less than
1.0kg, to avoid splashing of water
It is suggested not to use high sudsing detergent.Choose a low
suds or high efficiency detergent.
3. Detergent
Adding washing powder
It is suggested to dissolve the detergent before you put
them into the tub, see as below:
1.Prepare warm water of 35 C and container.
2. Add washing powder while stirring to dissolve it
completely.
Add washing powder into the box directly under
fuzzy program and reserve program.
Dissolve directly inside the washing machine: (not
applicable for fuzzy and reserve program)
How to use whitener
1.Add some water(select the " L " water level)
2.Add washing powder. Run for about 30s to fully
dissolve the powder. Then push the"start/pause"
button.
3.Put in laundries. Select suitable water level. Push
the "start/pause"button again.
Fill water to desired level.
Dilute the whitener in a
container. Pour it slowly
into the washing tub.
Avoid using whitener on
laundry with color or pattern
as they are prone to lose
color.
The whitener shall not touch
the laundry directly.
Refer to the whitener
instructions for the usage
and quantity.
Please add suitable washing powder as per the
laundries quantity, then set water level and water quantity.
If you select save program, it is suggested to use
liquid detergent instead of washing powder to
guarantee the washing effect.
It is not recommended to use rich-foam washing
powder.
Washing powder with poor quality or long-time
storage may get caked. Please clean the detergent
box periodically.
Note: For thebetter wash performance, please use lowing
sudsing or hign efficiency detergent andplease dissolve
the detergent in 1L warm waterfirst
For powder whitener,please
dissolve it before using .
4. Close the lid
If you open the lid during spinning the machine will stop and an alarm
will sound.
8
5 Operation
Long
A
Medium
Rapid
Express
B
E
D
F
C
G
Indicator display
On Indicates the program is about to run and indicates the selected cycle and options
Flashing Indicates the program is running and indicates the selected cycle and options
Remaining time display
Displays
Displays total remaining
Displays remaining time when the "Delay" program is used (hours).
Displays error codes (see page 12)
A
To turn off the power, press the power button.
If the start pause button is not pushed within 5 minutes, the washing machine will automatically
switch off the power.
B
START/PAUSE button
After the power is switched on press the Start/Pause button to start the machine.
During operation, push the Start/Pause button to pause the machine.
Push the Start/Pause button again to restart the machine.
C
Temp(Wash/Rinse
button
Press the Temp(Wash/Rinse)" button to select your wash temperature.
During quick cycle, the water temperature can't be chosen. Temp button does not work
During wool cycle, the "hot/cold" water temperature can't be chosen.
9
D
Water Level button
During the Memory and Synthetic programs the washing machine will detect the size
of the laundry and automatically select the water level between levels 4, 6, 8 or 10.
To change the water level, press the Start/Pause button and make your selection.
Press the Start/Pause button to start the machine, it will not set the water level
automatically.
If there is water inside the tub the machine cannot detect the laundry load and will
display water level "6". If wet laundry is put in the machine, it will display level "3",
the water level can be adjusted.
If Quick program is selected it will display water level
be adjusted
If Tub Dry program is selected the water level will not respond
3
the water level can
During operation of the wash, rinse or soak program, you can adjust the water level by
pressing the Water Level button.
The water level may vary due to the different moisture level of the laundry items.
E
Delay button
The display shows the time remaining (in minutes) before the cycle will finish.
Push the "Delay" button and the display will show the remaining time for the cycle to
finish (in hours). The indicator flashes to indicate that the delay function is operating.
Delay start (2-24hr) option
Delay time is the delay till the wash finishes.
F
Wash
Rinse
Spin button
You may change the Wash, Rinse and Spin times when Memory , Heavy Normal and
Synthetic cycles are selected.
When the Wool cycle has been selected you cannot change the Wash, Rinse and
Spin times.
You can not change the Wash Rinse and Spin times when Tub dry and Quick cycles
are selected.
10
G
Cycle button
Program
Recommended for
Normal
Washing the Mixed fabrics laundry
Heavy
Delicate
Quick
Items that are very dirty or items that are heavy or big
Delicate items that are machine washable
Small load of lightly soiled laundry less then 1.5kg
The customer favourable cycle, it can remember the cycle setted this
time(Water level will not be remembered because it will be setted by
funzzy function). For example, you choose Memory cycle this time
and then you set the wash time to Medium, rinse 2 times and spin time
to 5min, next time when you choose Memory cycle, it will work as this
time: Wash time: Medium, rinse 2 times and spin 5min.
Memory
Synthetic
Washing the Synthetic fabrics laundry
Machine washable woolen items
Wool
Drying the inner and outer tub to avoid the growth of mildew.
Tub dry
Operation buttons and descriptions
1
The machine has a power resume function. If the power fails the machine will
save the current program and resume the same program once the power supply
returns. The program does not need to be entered again.
Cycle
2
When the power is switched on "Normal" cycle is automatically set. To select
a different automatic cycle, press the "Cycle" button till the corresponding
indicator is on. Refer to the section on the "Cycle" button above.
E.g choose "Quick" cycle for a small load of lightly soiled laundry.
When the "Synthetic", Memory cycles are selected the Fuzzy
Logic program is run. The washing cycle is automatically set while the water
level and wash time can be selected according to the texture and size of the load.
11
Spin
Wash
Rinse
Press the
buttons to customise the pre-set options
3
During wool cycle, you can not set the washing time, rinse times and spin time.
You can only use the default settings.
Water
Level
Press the
button to change the water level
4
For the "Synthetic"and "Memory" cycles the machine will run the Fuzzy
Logic program automatically detecting the type of laundry in the tub. After detection
it will set the water level automatically. The water level can only be changed once
the machine has started, push the "Start/Pause" button, then push the "Water Level"
button to set the water level.
Temp
Press the
button to select the the wash and rinse temperature
Wash/Rinse
5
6
Press the Temp/ Wash/Rinse
and rinse temperature
button to select the the wash
Delay
Press the
button to select the delay wash program
The delay time program is automatically off. Select the Cycle and options required
and push the "Delay" button
The cycle indicator lights will go off and the "Delay (Hours) indicator light will be on.
During the delay program, press the "Delay" button to display the time remaining.
The delay time indicator shows the time remaining till the wash ends.
To change or cancel the delay program, switch the power off
and back on, then make a new selection.
Delay start (2-24hr) option
Delay time is the the end of washing
The wash will finish
in about 18 hours
12
Press the
button to start the cycle
7
and an alarm will sound.
Note
The energy test program was performed using the "Normal"
cycle default setting of: wash long , 1 rinse, spin 7 mins,
water level 10.
Please use low sudsing or high efficiency detergent.
Cycle completed
an alarm will sound.
13
7 Maintenance
Remove the power plug from the wall before cleaning.
Clean the lint filter after each wash.
The lint filter must be used during
washing.
Remove and clean the detergent
box, replace after cleaning.
It must be cleaned after each
use
Lint filter:
1.Pull it up to remove it.
2.Push it down to install.
3.Clean the filter screen after
each wash.
Dismantle
Install
remove
Install
Clean
The filter screen of the water inlet valve
may become to be blocked by foreign
materials and influence the water inlet.
Please clean it with brush every two
months.
If the cabinet is dirty, wipe it with a wet
cloth
Do not wash it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol,
alcohol etc.
l
ro
r
e
et
P
n
in
h
T
Alcohol
1.After washing, turn off the water faucet. ( If needed, you can remove the water
inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water
completely .
3.Remove the power plug before carrying out any cleaning or maintenance.
4.Hang up the power cord and drain hose.
5.Wipe up any drops of water on the surface of the machine and inside the tub.
Open the lid for about 1 hour , then close the lid.
14
Trouble-shooting
If there is a breakdown, remove the power plug before checking the machine. Using
the following list please confirm the machine requires repair. If repair is required
please contact our Customer Care Team, do not try to fix it yourself.
Problem
Possible causes
What to do
The machine does not
drain or drains slowly.
The display shows E1.
Remove the blockage.
Open and close the top
lid once.
Is the drain hose
blocked?
The machine stops running.
The display shows E2.
The top lid is not closed.
Close the top lid.
Redistribute the load evenly.
Close the top lid.
Level the machine. The
machine will start 10
seconds after being leveled
correctly.
The machine does not
spin. The display shows
E3.
Has the laundry been
place unevenly in the
machine?
Is the machine level?
Open the water tap. Push
the Start/Pause button once.
Clean the water inlet valve
then push the Start/Pause
button once.
Push the Start/Pause
button once.
Is the water tap opened, or
has the water supply been
interupted??
The display will show E4
within 30 minutes
Is the water inlet valve
blocked?
Is the water pressure too
low?
Please contact the
after-sales service
department.
The water level sensor
has failed.
The display shows E6.
Wait for the power supply
to be restored.
Insert the power plug
tightly.
Wait for water to fill to the
preset level.
Is there a power failure?
Will not
wash
Is the power plug inserted
tightly?
Has the water level reached
preset position?
The machine
does not
work.
Is the power plug inserted
tightly?
Is the top lid closed ?
Is the laundry distributed
unevenly in the machine?
Insert the power plug
tightly.
Close the top lid.
Redistribute the laundry.
Will not
spin
Is the machine level?
Redistribute the load evenly.
Close the top lid.
Level the machine.
There are abnormal
sounds inside the
machine
Has the laundry been place
unevenly in the machine?
Are there any foreign objects
inside the bowl?
Remove the foreign object.
Is the water inlet hose loose?
Fasten the inlet hose.
The water tap leaks
15
Common occurrences
Situation
Cause
The spinning is intermittent
when it starts.
Redistribute the load evenly.
Close the top lid.
The wash procedure pauses.
The cloth sensor is detecting , it will add
water after about 48 senconds.
The program is setting the drain time
a period of time is needed before the spin
program starts.
Select spin program, but it does
not work.
There maybe water in the
It is the water remaining after the
drain hose in when first used.
performance inspection by the factory.
16
Packing list
Name
Quantity
One
Storage position
User manual
Inside the document bag
One
Warranty card
Inside the document bag
Inside the accessory bag
Components of the
water inlet hose
Connect to the
Two
washing machine
Connect
to the tap
Lint filter
Inside the document bag
Inside the accessory bag
One
Tapping screws
Bottom plate
Eight
Between the upper cushion of the
washing machine package and the
upper seal of the package carton.
One
One
Automatic washing
machine
17
Specification
Fully Automatic Washing Machine
Type
HWMP55-918
220-240V
380W
Model
50Hz
Rated voltage/frequency
Rated washing power
Rated spinning power
Weight
300W
About 35kg
L 520 W 530 H 900
Dimensions (mm)
1/14 L 2/18L 3/22L 4/26L 5/30L
6/34L 7/38L 8/43L 9/47L 10/52L
Water level/Water
quantity(about)
0.03MPa-1.0MPa (when water temperature is
70 , the water inlet pressure of hot water
shall not exceed 0.4MPa)
Water inlet pressure
|