Haier Washer XQG50 600TXB User Manual

XQG50-600TXB  
XQG50-600SW  
Automatic Drum Washing Machine  
Table of Contents  
Before using  
Names of Parts--------inside front cover  
Matters Needing Attention------------1-3  
Installation--------------------------------4-5  
Control Panel-------------------------------6  
Operational Functions----------------6-7  
During using  
Program Selection------------------------8  
Preparation---------------------------------9  
Washing Methods--------------------10-11  
Maintenance  
Maintenance -----------------------------12  
Trouble Shooting------------------------13  
Technical Specification----------------14  
Wiring Circuit-----------------------------15  
0020502333  
 
Matters Needing Attention  
===Safety  
2. Hold the plug and not the electric cable  
when unplugging the washing machine.  
1. A separate earthed socket is required  
for the power supply. After installation of  
the washing machine,the power plug  
should be accessible during the normal  
wash.  
3. Fuses in the power circuit should be rated  
for 15A. Refer to a washing machine techni-  
cian or a Haier designated service point for  
power cable replacement.  
4. For your safety, dry hands before touch-  
ing the washing machine and wear appropri-  
ate footwear .  
5. Do not use flammable detergent or dry  
cleaning agent; do not use flammable  
spray in close vicinity to the washing  
machine; do not remove or insert the plug  
in the presence of flammable gas.  
6. The door of the washing machine will be-  
come hot during the water heating process.  
Avoid contact with the door during the heat-  
ing process. For safety, keep children away  
from the washing machine.  
7. Do not allow children play with the packing materials after unpacking.  
1
 
Matters Needing Attention  
Wiring Circuit  
9. The washing machine should be place in  
a well ventilated area maintaing a space  
between walls or furniture.  
8. The washing machine must not be used in  
the open or in area of high moisture as water  
droplets may form on electrical components,  
Air dry the appliance if the washing machine  
components become wet.  
10. Keep away from heat sources and direct  
sunlight to prevent plastic and rubber com-  
ponents from aging.  
11. During installation, ensure that the electric  
cable is not trapped by the washing machine and  
avoid damage to the electric cable.  
Dear customer, For the machine and your own  
security, DO NOT REPAIR IT BY YOURSELF!  
DO NOT USE THE WASHING MACHINE  
WHICH SOME PARTS ARE LOST!  
I1: Power Switch  
EVC: Hot Water Valve  
EVP,EVL: Cold Water Valve  
P1,P2: Pressure Switch  
THR: Adjustable Thermostat  
D: Drain Pump  
I2: Economic Wash Switch  
I3: No Spin Switch  
TM: Timer Motor  
===Use  
2. After turning the power off, turn the pro-  
gram knob clockwise to set washing  
program.  
1. Make sure that the washing machine is  
securely connected to the water supply,  
take the necessory precautions or contact  
the local service center if the connection  
is poor or there is a water leakage.  
H: Heating Element  
C:Capacitance  
S,W:Motor  
2
15  
 
Matters Needing Attention  
Technical Specification  
4. Do not wash foam rubber or similar sponge  
materials.  
3. Never place heavy objects ,a heating  
applianceor a water container on the top panel  
of the washing machine.  
Model  
Item  
XQG50-600TXB/XQG50-600SW  
220V~(50Hz)  
10  
Power supply  
Maximum working current  
(A)  
0.05 P 1 IPX4  
Water pressure  
Washing power  
(MPa)  
(W)  
5. Before washing, do up zippers, buttons ,  
laces and repair damaged areas,under-  
wear or small articals should be placed  
in the laundry bag or a pillowslip.  
6. Do not open the detergent box during  
the wash cycle.  
330  
650  
5
Spinning power  
(W)  
Do not wash clothes containing wire  
frames.  
Max. washing load  
Spinning speed  
(kg)  
(r/min)  
600  
14  
Washing program  
Heating power  
8. After washing, turn off the tap to prevent  
leakage; unplug the washing machine  
and wipe clean the lower part of the port  
hole.  
7. The door is fitted with a self-lock device and  
will not open until 2~3 minutes after the wash-  
ing machine stops. Do not force the door  
open. Do not open the door when water level  
reaches the port hole.  
(W)  
1950  
Size (HXDXW)  
Weight  
(mm)  
850x550x595  
(kg)  
76  
9. Keep the door slightly open when the washing machine is not being used. Never cover the  
machine with a plastic sheet.  
14  
3
 
Installation  
As shown in figure1 remove all the packing materials  
Trouble shooting  
The following circumstances do not constitute problems. Do not contact the  
maintenance service until the problem has been confirmed.  
(including the foam base).  
Problem  
Possible Cause  
Poor connection to power supply  
Power failure  
Door is not properly closed  
Machine has not been switched on  
The washing machine fails to  
operate  
Fig 1  
Check attachments and materials.  
Water is not turned on  
Water pressure is less than 0.05MPa  
The inlet hose is kinked  
Water supply failure  
Name  
Operational  
Washing machine does not fill  
with water  
Quality  
Water  
hose  
Drainage  
holder  
Plastic  
plugs  
Qty  
manual  
certificate  
The program knob is not properly set  
The door is not properly closed  
Model  
XQG50-600TXB  
XQG50-600SW  
1
1
2
1
3
The water supply and  
drainage do not stop  
== Check that the height of the water hose is below  
80cm  
==Remove the packing screws as shown in figure 2.  
The packing bolts protect the appliance from shock during trans-  
portation The steps below should be followed before using the  
appliance,  
1. Remove the rear panel of the washing machine;  
2. Remove the three packing bolts from the rear panel of the wash-  
ing machine,the rubber hose and then the shock absorption chan-  
nel steel;  
= Drainage hose is blocked  
= Drainage hose end is over 100cm above the  
floor level  
Drainage failure  
3. Reinstall the back plate;  
==Some packing fixing bolts removed  
Washing machine on a uneven surface  
Strong vibration during spin  
4. Fill the holes left by the packing bolts with plastic plugs.  
(Attention: the packing bolts and rubber hose should be kept in a  
safe place for later use)  
cáÖ=O  
Operation stops before comple-  
tion of the wash cycle  
Water or electricity failure  
===Adjusting the position of the washing machine .There are ad-  
justable feet under the bottom of the washing machine. Before use,  
the washing machine should be adjusted, as shown in figure 3, so  
that it is level.  
= The detergent is not a low foam type  
Excessive foam in the drum  
Excessive detergent has been used  
cáÖ=P  
4
13  
 
Installation  
Maintenance  
Connection of water inlet hose and washing machine  
1. Turn of the water and electricity supply  
after every wash. Open the door to pre-  
vent the formation of moisture and odors.  
If the washing machine is left idle for a long  
period, drain any remaining water in the  
machine and replace the drainage hose.  
2. Unplug the machine during cleaning and  
maintenance. Use a soft cloth dampened with  
soapy liquid to clean the machine case and rub-  
ber components. Do not use corrosive or abra-  
sive chemicals or solvents.  
3. Clean the detergent compartment  
regularly. For the detergent compartment  
similar to figure (a), raise the compartment  
slightly to remove and replace after cleaning.  
4. Cleaning the Filter (once a month)  
Press the lower edge of the filter compartment  
cover to open; (Fig1-2)  
Remove the filter by turning counterclockwise;  
(Fig3)  
Water drainage hose  
= The height of the terminal of the water drainage  
hose should be between 80cm-100cm, the water  
drainage hose must be securely placed on the clip  
on the back of the washing machine.  
Flash clean with running water;  
Filter replacement is the reverse of removal. Cau-  
tion: Attention shall be paid to ensure that the filter  
is replaced correctly to avoid possible leakage.  
Use the water drainage support supplied as an  
accessory for proper installation of the water drain-  
age hose .fix the water drainage hose support with  
waterproof sring.Do not use an excessively long wa-  
ter drainage hose and contract the authorized tech-  
nician if the water drainage hose needs to be  
extended.the water drainage hose should not be ex-  
tended more than250cm.(longer extension will result  
in concurrent water inflow and outflow).The diam-  
eter of the extension hose should be the same as  
the original hose.  
Fig (a)  
fig.1  
fig.2  
fig.3  
caution:water drainage hose must not be immersed  
in water.the original and extension hoses should be  
tightly connected .  
5. To prevent block-  
ages to the water sup-  
ply or the ingress of  
contaminants, clean  
the water inlet and in-  
l e t w a t e r f i l t e r  
regularly.  
6. If the machine is to be moved a distance location,  
replace the vibration mounting locks which were re-  
moved during installation as shown below.  
Connection of power supply  
Check the following items before connection to the power supply.  
==The socket conforms to the maximun power load(The maximum current load of the socket and  
power supply cable should not be less than 15A)K  
Replace the rubber Insert the bolts.  
plugs.  
Remove the back  
cover.  
Power supply voltage conforms to the required value.  
7. If the washing machine is left idle  
for a long period turn off the water and  
electricity supply and open the door  
slightly to prevent the formation of  
moisture and odors.  
==The power supply socket and the plug of the washing machine compatible,if they are not com-  
patible ,Refer to a washing machine technician or a Haier designated service point for power cable  
replacement.The washing machine should be connected to an earth before use.  
= Supplementary earth cable should not be necessary if the socket is connected to the earth.  
= Supplementary earth cable should be installed on the upper back of the washing machine  
andconnected to an earth if the power supply socket has no earth connection.  
Replace the back  
cover.  
Tighten the bolts with a  
spanner.  
12  
5
 
Washing Methods  
Control Panel  
4. Washing temperature Setting  
C
F
D E  
Set the washing temperature as required, otherwise, set at position * when heating is not  
needed.  
5. Selecting the function button  
Select function buttons as required (refer to the directions printed on the control panel) ,  
otherwise keep all the button released.  
G B  
A
C
F
D E  
6. Washing  
XQG50-600SW  
Press the power button and the washing machine will automatically commence the pro-  
grammed washing process.  
7. End  
G B  
A
Wait 2-3 minutes after the washing process is finished, press the power button again to cut  
off the power supply. Open the door to take out the laundry. Turn off the tap and unplug the  
washing machine.  
A Washing program  
Turn the knob clockwise to set the desired wash program .  
Caution: Turn off the power and turn the program knob clockwise  
for setting desired wash program.  
Additional information  
B Washing temperature  
Energy and water saving during wash process  
1. Collect clothes for one full wash load.  
2. Do not overload the washing machine.  
Turn the knob clockwise to set the desired temperature.  
Temperatures between 30OC-90OC can be setted , No  
heating wash is selected when the knob is set at *.  
3. Pre-wash heavily soiled clothes.  
4. Reduce the amount of detergent or choose fast or minimal washing programs for lightly  
soiled clothes dirty.  
5. Choose a proper washing temperature. Only exceed 60 OC for heavily soiled clothes.  
6. Do not use more detergent than required.  
C Detergent distributor  
Program discription are printed on the handle of the detergent  
distributor,there are three detergent compartments numbered 1,2,3  
Box 1: Pre-washing detergent  
7. Softening agent makes clothes feel softer and easier to iron.  
2
1
3
Box 2: Standard washing - extra-fast washing  
Box 3: Softening agent, adjusting agent, perfume  
6
11  
 
Operational Functions  
Washing Methods  
1. Laundry loading  
Reference loading  
Evenly load the laundry in the  
D No spin button  
=Overalls  
=Jeans (800g)  
Pajamas (200g)  
washing machine and then tightly  
close the door of the washing  
machine  
Note: 1) When first using the  
washing machine, let it run un-  
loaded for one program to pre-  
vent the laundry from being  
tainted by oil or dirty water from  
the washing machine. 2) Do not  
overload the washing machine.  
(cotton 950g)  
When this button is pressed, the spin cycle will be spared but water  
drain is still available. This function is useful for hard ironing fabrics,  
such as chemical fiber and wool fabrics.  
=Blended  
fabric clothes  
(800g)  
====Shirts  
(300g)  
===Underwear  
(blended fabrics 70g)  
=Socks  
=shirt  
(cotton  
300g)  
=====Jackets  
(cotton 800g)  
(blended fabrics 50g)  
E Economic wash button  
=Single bed sheets  
=Woolen blankets  
(3000g)  
(cotton 800g)  
Pressing this button will reduce the consumption of water during  
bleaching under intense wash. It is recommended that this  
program be used when doing a small laundry load.  
2. Use of detergent  
Do not forget to reduce the amount of detergent used.  
Pull out the detergent drawer, put required detergent, soften-  
ing agent and bleaching agent into the corresponding boxes.  
Push back the drawer gently.  
Caution: 1) Do not add liquid detergent into box 1 and 2  
2) For pre-washing program, detergent should  
be added to both box 1 and 2; for other  
programs, do not add detergent to box 1  
3) Do not overuse softening agent as this may  
damage artificial fabrics.  
F Power button  
ON  
OFF  
Press the button ,washing machine will working;release the button,the  
washing machine will stop.  
3. Washing program setting  
Set the wash program correctly in accordance with the laundry load.the methods for  
setting wash programs are indicated on the handle of the distributor on the washing  
machine.turn the program knob clockwise to the desired program.  
Caution: Turn off the power before setting the wash program.  
G Power light  
The light will illuminates when the power supply is connected.  
10  
7
 
Preparation  
Program Selection  
2. Water supply  
1. Power supply  
Turn on the tap ensure that the water is clear.  
Plug in the power supply  
220V~/50Hz.  
Caution: Before staring the washing machine turn on the  
water faucrt to ensure that the water faucet and the water  
inlet hose are connected correctly and do not leak.  
3. Laundry treament  
4. Detergent selection  
Only special low foam detergent  
should be used in automatic  
drum washing machine, form  
blended or wool fabrics special  
detergent should be used. dry  
cleaning solvent should not be  
used such as trichhloroethylene  
or alike (caution :load the re-  
quired amount of detergent only).  
=sort out clothes according to type and extent of dirt.  
There are three types of clothes: cotton, synthetical and  
woolen (silk) fabrics.  
separate white clothes from colored. If whites and  
coloreds are combined for one load, make sure the  
coloreds are colorfast.  
-Remove all objects from pockets that may cause dam-  
age to the machine, such as keys and coins.  
-Clothing with frayed edges or yarns should be put in a  
wash bag or special bag before washing.  
-Repaire damaged clothing,lose buttons or damaged zips  
and hooks before washing.  
-Bed sheets and table ware should be loosely loaded and  
not folded.  
=This washing machine is for household use and de-  
signed for mechanically washable clothes. When washing,  
separate unwashable clothes with reference to clothes  
labels.  
5.Wash Load  
Woolen fabrics  
1kg  
Blending fabrics  
2.5kg  
Type  
non-fade cottons  
5kg  
Delicat fabrics  
2kg  
Max load  
NOTE: ” o ”means softener liquid detergent canbe added when necessary.  
”means detergent can be added when necessary.  
”means no detergent can be added.  
8
9
 

Graco Car Seat PD202326A User Manual
Graco Inc Paint Sprayer 218 026 User Manual
Grundig Stereo System UMS 4200 User Manual
Hasbro Motorized Toy Car 3906 User Manual
Heath Zenith Home Security System 5326 User Manual
Honeywell Oxygen Equipment Y8610U User Manual
Hoshizaki Refrigerator CF1B FG FGY FS HS CR2B FG FGY FS HS User Manual
HP Hewlett Packard Printer 1055CMHP User Manual
Hypertec Mouse 260 PS 2 User Manual
IKEA Double Oven OV9 User Manual