Humidifier
Humidifier Safety............................ 2
Know Your Humidifier.................... 4
How to Assemble and Use............ 5
How to Clean................................ 11
Troubleshooting Guide ................ 14
Customer Service.......................... 16
In USA: 1-800-851-8900
In Canada: 1-800-267-2826
840074800
Consumer Safety Information
This appliance is intended for
household use only.
If a longer cord is necessary an
approved extension cord may be used.
The electrical rating of the extension
cord must be equal to or greater than
the rating of the humidifier. Care must
be taken to arrange the extension cord
so that it will not drape over the coun-
tertop or tabletop where it can be
pulled on by children or accidentally
tripped over.
This appliance is equipped with a
polarized plug. This type of plug has
one blade wider than the other. The
plug will fit into an electrical outlet
only one way. This is a safety feature
intended to help reduce the risk of
electrical shock.
If you are unable to insert the plug into
the outlet, try reversing the plug. If the
plug should still fail to fit, contact a
qualified electrician to replace the
obsolete outlet. Do not attempt to
defeat the safety purpose of the
polarized plug by modifying the plug
in any way.
Do Not Over-humidify
Do not over-humidify. The suggested
level for the best health benefit is 50%.
Some units can be set for desired
humidity ranges from 20 to 90%, but
care should be taken not to over-
humidify, which will be dependent on
both the construction of your home
and the outside weather conditions.
Do not allow water to condense on
walls, floors, or windows as water
damage could result. If you see these
conditions occur, lower the desired
humidity level on the humidifier or turn
the unit off. Hamilton Beach/Proctor-
Silex, Inc. will not be responsible for
damage caused by water.
Before First Use
Be sure to remove all packing materials. Do not place the humidifier where it
Choose a flat, level, water-resistant or its cord presents a tripping or
location for the humidifier that will allow stumbling hazard, or where the air
for good air circulation and that is not
accessible to children.
vents are blocked.
3
Know Your Humidifier
Parts and Features
Fan Enclosure
1. Control Panel
2. Exhaust Grille
3. Cord Wrap (see page 6)
4. Air Intake Grilles
Water Tank Assembly
5. Carrying Handle
6. Water Tank
7. Gasket
8. Filler Cap
Base Assembly
9. Filter
10. Water Tray
11. Humidifier Base
4
How to Assemble and Use
IMPORTANT: Your Hamilton Beach humidifier is designed for easy use and
maintenance. Make sure that the water tray and filter are properly installed before
filling the tank and operating the humidifier.
DO NOT USE THE HUMIDIFIER WITHOUT THE FILTER IN PLACE!
Selecting the Proper Location
To prevent the risk of injury or damage to the humidifier and furnishings and
provide the best possible performance of your humidifier, follow the placement
guidelines below:
DO:
DO NOT:
• Place the humidifier on a flat, stable,
• Do not stand, sit, or place any
waterproof
surface.
objects on
the humidifier.
It is not
designed
to support
additional
weight.
• Place the humidifier along an inside
wall near an electrical outlet where
it is out of the way and it and its cord
do not present a tripping hazard.
• Select a location with adequate
air circulation.
• Leave at least six inches (15 cm)
between the humidifier and any walls
or furnishings. Failure to do so could
cause poor air circulation and
mildew or moisture damage to walls
or furniture.
• Do not block the air intake and
exhaust grilles. This will cause poor
performance and may cause moisture
damage and mildew build-up.
• Do not use in a small, enclosed
space or in an area with a humidity
level above 50%. Excessive humidity
could result.
• Do not place on or near heat sources
such as stoves, radiators, or heaters,
or in direct sunlight.
• Never place the humidifier in a
closed room. A closed room may
result in excessive humidity.
• To reduce electrical noise and
interference, do not place on or near,
or plug into the same outlet as, TVs,
baby monitors, or cordless phones.
• Unplug the humidifier and empty the
water tank and tray if the humidifier is
to be moved, or will not be used
for several days.
5
Humidifier Assembly
3. Slide the cord through the notch at
the bottom
1. Insert the water tray into the humidifier
base. Be
of the cord
sure that it
is securely
seated in
the indent
in the base.
wrap com-
partment.
Excess cord
can be
stored in
the cord wrap
compartment.
2. Place the filter on the water tray
as shown.
4. Set the fan enclosure onto the
humidifier
base. Make
sure that
the filter
lines up
with the
fan cover.
6
Filling the Water Tank
1. Remove the filler cap on the bottom
3. Replace the filler cap and turn
of the tank
by turning it
counter-
clockwise
until the
LOCK
clockwise
until the
UNLOCK
arrows line
arrows line
up with the
ridges on
the tank
up with the
ridges on
the tank.
opening.
Return the
tank to
Unlocked
Position
Locked
Position
an upright
2. Fill the tank with COOL tap water.
position. When carrying the tank, use
the carry handle and support the
tank from the other side.
NOTE: Always make sure the filler
cap is locked and the gasket is in
place before inverting water tank.
DO NOT
USE HOT
WATER.
Be sure to
keep the
tank free of
debris.
Filter Tip!
To prolong the life of the filter, it is
recommended that you turn over the
filter each time you fill the water tank.
NOTE: Using distilled or deionized
water will prolong the life of the filter.
7
Placing the Water Tank on the Base
Lower the tank into place until it is
properly seated,
NOTE: Some water will flow out of
the tank and into the water tray when
the tank is in position.
CAUTION: Once the humidifier has
been filled, do not attempt to tilt or
move it. If it is necessary to move
the humidifier, make sure it is
unplugged and remove the water
tank first.
using the fan
enclosure and
the base to align
the tank.
IMPORTANT! Never pour water into
or allow water to splash into air intake
or exhaust grilles.
Plugging in the Humidifier
WARNING: To reduce the risk of
electrical shock, never plug in the
humidifier while your hands are wet!
Once the humidifier has been assembled
and placed in its final location, and the
tank has been filled, plug the humidifier
into a wall outlet.
NOTE: The polarized plug will only
fit in one direction—DO NOT try
to force the plug! If you are unable to
insert the plug into the outlet, try
reversing the plug. If the plug still does
not fit, contact a qualified electrician to
replace the obsolete outlet.
8
Setting the Controls – 2-Speed Humidifier
Setting the fan speed
Turn the fan speed knob to the
desired setting. To increase the
humidity in a room more quickly, set
the knob to HI. For quiet, nighttime
operation or for a more gradual
increase, set the knob to Quietmist™.
Indicator lights
The power on indicator will light to
indicate that the humidifier is on.
1. Fan Speed Knob
2. Power On Indicator – lights
when unit is on.
Setting the Controls – 2-Speed Humidifier with Humidistat
Setting the fan speed
Turn the fan speed knob to the
desired setting. To increase the
humidity in a room more quickly, set
the knob to HI. For quiet, nighttime
operation or for a more gradual
increase, set the knob to Quietmist™.
Setting the humidistat
The desired humidity knob allows
you to set the humidifier to cycle on
and off to maintain a selected humidity
level. Turn the knob clockwise for
higher humidity, counterclockwise for
less. Once the desired humidity level is
reached, the desired humidity indicator
will light and the fan will turn off (unit
1. Fan Speed Knob
2. Power On Indicator – lights
when unit is on.
3. Desired Humidity Indicator –
lights when desired humidity is
reached.
4. Desired Humidity Setting Knob
is in stand-by mode).
Indicator lights
The power on indicator will light
to indicate that the humidifier is on.
Quietmist™
For quiet, nighttime operation or
for a more gradual increase in the
humidity level, set the knob to
Quietmist™.
9
Setting the Controls – 3-Speed Humidifier with
Electronic Humidistat
Setting the fan speed
Turn the fan speed knob to the
desired setting. To increase the
humidity in a room more quickly, set
the knob to HI. For normal operation,
set the knob to MED. For quiet,
nighttime operation or for a more
gradual increase, set the knob to
Quietmist™.
Setting the electronic humidistat
The electronic humidistat allows you to
set the humidity within a range from
1. Fan Speed Knob
2. Humidity Setting Buttons (▲/▼)
20% to 90%, in 5% increments. The
current room humidity level is displayed
in large numbers, while the desired
humidity level is displayed in smaller
numbers. If the current room humidity
level drops below 20%, the display will
show LO. If it is higher than 90%, HI
will be displayed. Press the ▲ and ▼
buttons to adjust the humidity level. The
humidifier will then turn on automatically
whenever the current room humidity
drops more than 2% below the desired
humidity. Once the desired humidity is
reached, the fan will turn off and the
unit will go into stand-by mode.
3. Power On Indicator – lights when
unit is on
Digital Display
4. Current Room Humidity Percentage
5. Desired Humidity Percentage
Quietmist™
For quiet, nighttime operation or
for a more gradual increase in the
humidity level, set the knob to
Quietmist™.
Indicator lights
The power on indicator will light to
indicate that the humidifier is on.
10
How to Clean
The evaporative, wick-type humidifier
adds moisture to the air in the form of
water vapor, by using a fan to force air
through a moistened-filter medium.
Failure to follow the recommended care
and maintenance instructions could
lead to a buildup of micro-organisms,
including algae, bacteria, and mildew,
which may lead to respiratory or other
ailments in some individuals.
To ensure the proper and efficient
operation of your humidifier, the
following cleaning and maintenance
procedures must be followed.
wWARNING
To reduce risk of electric shock:
• Always unplug before cleaning.
• Do not immerse fan enclosure in water or other liquid.
Cleaning the Humidifier
Wipe the fan enclosure, control panel, and cord with a damp cloth or sponge.
Daily Maintenance:
1. Turn off the humidifier and unplug it
5. Reinstall the water tray and filter,
replace the fan enclosure, and refill
the water tank with cool tap water
as instructed on page 7.
from electrical outlet.
2. Lift off the fan enclosure and remove
the filter.
NOTE: To prolong the life of the filter,
it is recommended that you turn over
the filter each time you fill the water
tank.
3. Remove the water tank and tray
and carry them to the sink. Pour
any remaining water into the sink.
4. Rinse the water tray and tank
thoroughly to remove any dirt or
sediment. Wipe clean, then dry
with a clean cloth or paper towel.
Weekly Maintenance:
1. Turn off the humidifier and unplug
5. Inspect the filter each week. If it
becomes hard to the touch, or
shows discoloration (caused by
mineral deposits or mold/mildew
buildup), it should be replaced.
See page 16 for information about
ordering a replacement filter.
it from electrical outlet.
2. Lift off the fan enclosure and remove
the filter.
3. Remove the water tank and tray and
carry them to the sink. Pour any
remaining water into the sink.
4. To remove scale caused by hard
water deposits and to clean the tank
and water tray, these parts can be
either cleaned in a dishwasher or
washed by hand.
6. After cleaning and drying all parts,
follow the instructions on page 6
to reassemble the humidifier. If the
humidifier will not be used for at
least two weeks, see the “Storing
the Humidifier” section.
11
Preferred Cleaning Method
(Cleaning in a dishwasher)
Water
Tank
The parts shown on the right are
dishwasher-safe for easy cleaning.
These parts are a transparent smoke
color for easy identification.
Filler
Cap
NOTES:
• Always wash humidifier parts
separately from dishes.
• Always use a heated water wash
cycle.
• If your dishwasher has a heated dry
cycle, it should be turned OFF.
Water
Tray
• Do not use rinse aid while cleaning
humidifier parts.
• ALWAYS remove the filler cap from
the water tank before placing the
tank in the dishwasher.
Tip!
1. Place the filler cap in the dishwasher’s
silverware basket. This small part
must be secured in the silverware
basket to prevent it from being
damaged by the dishwasher.
If the water tank won’t stand up in your
dishwasher, try moving the silverware
basket to another area in the dishwasher
and place the tank in the silverware
basket recess.
2. Place water tank in the dishwasher
with the tank opening facing down if
possible. This position will trap the
least amount of water in the tank.
12
Alternate Cleaning Method
(Cleaning by hand)
To remove mineral deposits:
To clean the tank:
1. Partially fill the water tray with a
solution of one gallon water and
8 ounces undiluted white vinegar.
2. Allow to stand for 20 minutes,
then clean all interior surfaces
with a soft brush.
1. Fill the tank with one gallon of water
and one teaspoon of chlorine bleach.
2. Replace the filler cap, and let the
solution stand for 20 minutes,
swirling it around the tank every few
minutes to wet all inside surfaces.
3. Dampen a soft cloth and wipe out
3. Empty the tank, rinse tank and filler
cap thoroughly with water until no
bleach smell is noticeable. Dry with a
clean cloth or paper towel.
entire tray to remove scale.
4. Rinse thoroughly with clean warm
water to remove any remaining scale
and vinegar/water solution.
Storing the Humidifier
If the humidifier will not be used for at least two weeks:
1. Unplug the humidifier.
2. Empty the water tank and water tray.
3. Discard the filter. DO NOT leave it in
the humidifier. To order a new filter,
see page 16.
6. Make sure all parts are completely
dry. DO NOT leave any water in the
humidifier when storing it.
7. Place the humidifier in the original
box and store in a cool, dry place.
8. Clean the humidifier and install the
4. Follow the cleaning instructions for
new filter before using it again.
weekly maintenance.
5. On models with a manual humidistat,
turn the humidistat to the minimum
setting.
13
Troubleshooting Guide
The following section provides the solutions to many common problems and
questions. If your humidifier is not working correctly, review these solutions first;
it may save you a phone call. If your problem is still not solved after reviewing
this guide, call our toll-free customer service number, listed on the cover of this
manual.
The Humidifier Will Not Turn On
• Is the tank filled and properly seated
on the base?
• Is the humidifier plugged into a
powered outlet?
• Is the desired humidity set lower
than the current room humidity level?
The humidifier turns on automatically
when the desired humidity is higher
than the current room humidity.
• Is the humidifier turned on?
The Tank Leaks
• Is the filler cap gasket in place?
If not, press it into the groove
around the tank fill opening. If the
gasket seal is missing or damaged,
call the customer service number
on the cover to order a replacement
gasket. Do not use the humidifier
without the gasket in place.
• Is something trapped under the edge
of the rubber seal in the center of the
filler cap? Check for debris under the
edge of the seal, or for damage to
the seal. If the seal is damaged, a
replacement seal can be ordered
by calling the customer service
number on the cover.
• Is the filler cap locked tightly? Make
sure that the “LOCKED” arrows line
up with the ridges on the fill neck.
The Tank Is Full But the Tray Does Not Fill
• Is the cord or another object trapped
under the tank? Make sure that the
tank is properly seated on the base
and that the power cord is routed
correctly. If the tank will not seat
properly, see “Fan Enclosure or
Tank Does Not Fit on Base.”
14
The Filler Cap Is Difficult to Remove
• Sometimes a vacuum can form in
the tank,
• Apply 100% pure petroleum jelly
to the filler cap gasket. Wipe off
any excess.
especially
if it has not
been seated
on the base
for a long
period of
time. Press
the button
in the center
Press here
of the filler cap to relieve the vacuum.
Fan Enclosure or Tank Does Not Fit on Base
• Make sure that the cord or other
objects are
• New filters are shipped flat and must
be “rounded” before installation.
Gently pull the filter into a round
shape, being careful not to tear it.
Once the filter is properly rounded,
install it and lower the fan enclosure
into place (as described on page 6).
not trapped
under the fan
enclosure
or tank.
• Is the cord routed correctly? The
cord should
be pressed
completely
into the cord
exit notch.
Any excess
cord should
be completely
behind the
tabs in the
New filter
Rounded filter
Cord
behind
tabs
Cord
exit
notch
cord storage compartment, as
shown above.
15
Customer Service
If you have a question about your humidifier, call our toll-free customer service
number. Before calling, please note the model, type, and series numbers and fill
in that information below. These numbers can be found on the back of the fan
enclosure. This information will help us answer your question much more quickly.
MODEL: ______________ TYPE: _______________ SERIES: _________________
THREE-YEAR LIMITED WARRANTY
Hamilton Beach/Proctor-Silex, Inc. warrants this appliance to be free from defects in
material and workmanship for a period of three (3) years from the date of original purchase,
except as noted. There is no warranty with respect to the following, which may be supplied
with this appliance: the filter. This warranty extends only to the original consumer purchaser
and does not cover damage from abuse, neglect, use for commercial purposes, or any
other use not found in the printed directions. HAMILTON BEACH/PROCTOR-SILEX, INC.
EXPRESSLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ANY
LIABILITY HEREUNDER IS EXPRESSLY LIMITED TO THE REPAIR OR REPLACEMENT
OF A DEFECTIVE PRODUCT OR AN AMOUNT EQUAL TO THE PURCHASE PRICE PAID
THEREFOR, AND ALL CLAIMS FOR SPECIAL AND CONSEQUENTIAL DAMAGES ARE
HEREBY EXCLUDED. Some states or provinces do not allow this exclusion or limitation of
incidental or consequential losses, so the foregoing disclaimer may not apply to you. If you
have a claim under this warranty, DO NOT RETURN THE APPLIANCE TO THE STORE!
Please call our CUSTOMER SERVICE NUMBER. (For faster service please have model,
series, and type numbers ready for operator to assist you.)
CUSTOMER SERVICE NUMBERS
In the U.S. 1-800-851-8900
In Canada 1-800-267-2826
KEEP THESE NUMBERS FOR FUTURE REFERENCE!
This warranty gives you specific legal rights, and you may also have other legal rights
which vary from state to state, or province to province.
Replacement Filters:
Humidifier
Capacity:
USA
Models:
Canada
Models:
Filter
Part Number:
2.5 gallons/day
3.5 gallons/day
05518 & 05519
05520 & 05521
05518C & 05519C
05520C & 05521C
05910
05920
HAMILTON BEACH PROCTOR-SILEX,INC.
PROCTOR-SILEX CANADA,INC.
Picton, Ontario K0K 2T0
263 Yadkin Road
Southern Pines, NC 28387
840074800
8/00
16
|