AIR HOSE REEL
WITH 30’ , 3/8" HOSE
Model 40131
INSTALLATION and OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright 2002 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
9. Maintain tools with care. Keep tools clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords and air hoses
periodically and, if damaged, have them repaired by an authorized technician. The
handles must be kept clean, dry, and free from oil and grease at all times.
10. Disconnect air supply. Disconnect air hose when not in use.
11. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
12. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified
technician.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.
14. Do not operate air tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.
15. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.
WARNING: The brass components of this product contain lead, a chemical known to
the State of California to cause birth defects (or other reproductive harm). (California
Health & Safety code § 25249.5, et seq.).
Warning:The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator. Read and understand all
of the instructions provided in the instruction manual of the air compressor being
used.
Page 3
SKU 40131
REV 03/07
Unpacking
When unpacking, check to make sure the parts listed on page 5 are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
FIGURE 1
Installation
1. You may mount your Hose Reel on a wall,
workbench, or a ceiling. The surface you mount
to must be capable of holding the weight of the
Hose Reel, the hose, and the additional stress
from tugging on the unit with the hose extended.
2. Mount the unit through the four
mounting holes on the Base (#1) with four
bolts (not included) fitted for 13/32” diameter holes.
See FIGURE 1.
3. Thread the Handle (#23) onto
the Flange A (#6) assembly.
Base (#1)
Operation
Warning!! Do not exceed 250 PSI with this Hose Reel.
1.You may need to prepare a 1/4” air connector (sold separately) to connect to the air source
hose.
2. Wrap the 1/4” air connector (not included) with pipe thread seal tape before connecting the
air source hose to the InputValve (#24) on the Hose Reel.The Hose on the Hose Reel comes
pre-attached to the Swivel (#13).
3. Check the air connection for leaks.
4. When using the Hose Reel, remove hose from reel slowly. If it binds up, do not force it.
5. When reeling on hose, make sure the hose covers the Hose Reel evenly, and does not
bunch up on either end.
Warning: Read and adhere to all safety warnings and instructions provided in the in-
struction manual of the Air Compressor being used with this product.
Maintenance
1. Periodically check connection for air leaks.
2. Keep the hose clean and free of dirt and debris by wiping it down before winding it on to the
Hose Reel.
Page 4
SKU 40131
Parts List
Part No.
1
Description
Base
Qty.
1
2
Stand
1
3
4
Fixed Washer
Washer
1
1
5
6
7
Position Sleeve
Flange A
Sleeve
1
1
1
8
9
Flange B
Position Sleeve
Washer
Spring
Washer
Swivel (2 valves & 0-rings) 1
Spring Washer
Nut
Washer
Rubber Protector
Clamp
Screw
Screw
Washer
Nut
Handle
Input Valve
Locking Pin
Hose
1
1
1
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
1
3
3
1
1
3
3
3
3
1
1
1
1
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KINDTOTHE BUYERTHAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Page 5
SKU 40131
Assembly Drawing
2
3
24
26
22
23
14
13
Page 6
SKU 40131
|