Harbor Freight Tools Dust Collector 47911 User Manual

DUST COLLECTOR ACCESSORY KIT  
Model 47911  
ASSEMBLY AND OPERATING INSTRUCTIONS  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright 2002 by Harbor Freight Tools®. All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions, please call 1-800-444-3353.  
 
7.  
DO NOT OVERREACH. Keep proper footing and balance at all times to prevent  
tripping, falling, back injury, etcetera.  
8.  
9.  
INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENT.  
STAY ALERT. Watch what you are doing at all times. Use common sense. Do  
not use this product when you are tired or distracted from the job at hand.  
10.  
11.  
CHECK FOR DAMAGED PARTS. Before using this product, carefully check that  
it will operate properly and perform its intended function. Check for damaged  
parts and any other conditions that may affect the operation of this product.  
Replace or repair damaged or worn parts immediately.  
REPLACEMENT PARTS AND ACCESSORIES: When servicing, use only  
identical replacement parts. Only use accessories intended for use with this  
product. Approved accessories are available from Harbor Freight Tools.  
12.  
13.  
14.  
MAINTAIN THIS PRODUCT WITH CARE. Keep this product clean and dry for  
better and safer performance.  
MAINTENANCE: For your safety, service and maintenance should be performed  
regularly by a qualified technician.  
USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool,  
attachment, or accessory to do the work of a larger industrial tool, attachment, or  
accessory. There are certain applications for which this product was designed. It  
will do the job better and more safely at the rate for which it was intended. Do  
not modify this attachment, and do not use this product for a purpose for which it  
was not intended.  
15.  
WARNING: The warnings, precautions, and instructions discussed in this manual  
cannot cover all possible conditions and situations that may occur. The operator  
must understand that common sense and caution are factors, which cannot be  
built into this product, but must be supplied by the operator.  
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS  
1.  
2.  
MAINTAIN A SAFE WORKING ENVIRONMENT. Keep the work area well lit.  
Make sure there is adequate surrounding workspace. Always keep the work  
area free of obstructions, grease, oil, trash, and other debris.  
MAKE SURE TO READ AND UNDERSTAND ALL INSTRUCTIONS, AND  
SAFETY PRECAUTIONS, AS OUTLINED IN THE MANUFACTURER’S  
MANUAL OF THE POWER EQUIPMENT TO WHICH THE DUST COLLECTOR  
ACCESSORY KIT WILL BE ATTACHED.  
SKU 47911  
PAGE 3  
 
3.  
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and  
other construction activities, contain chemicals known (to the State of California)  
to cause cancer, birth defects or other reproductive harm. Some examples of  
these chemicals are: lead from lead-based paints, crystalline silica from bricks  
and cement or other masonry products, arsenic and chromium from chemically  
treated lumber. Your risk from these exposures varies, depending on how often  
you do this type of work. To reduce your exposure to these chemicals: work in a  
well ventilated area, and work with approved safety equipment, such as those  
dust masks that are specially designed to filter out microscopic particles. (Cali-  
fornia Health & Safety Code 25249.5, et seq.)  
UNPACKING  
When unpacking, check to make sure all the parts shown on the Parts List on page 6 are  
included. If any parts are missing or broken, please call Harbor Freight Tools at the num-  
ber shown on the cover of this manual as soon as possible.  
PRODUCT OVERVIEW  
1.  
The Dust Collector Accessory Kit is designed for one and two power equipment  
tool hook-ups, and is typically used for the collection of wood dust, wood chips,  
sand, and other light debris. The Dust Collector Accessory Kit may be attached  
to table saws, band saws, sanders, router tables, shapers, jointers, and variety of  
dust collecting machines all having a 4” dust port. Due to the wide diversity of  
power machinery to which the Dust Collector Kit may be attached, it is recom-  
mended that only a qualified technician perform the assembly procedure.  
ASSEMBLY INSTRUCTIONS  
NOTE: For additional references to the parts listed below, refer to the  
AssemblyDiagram on page 6.  
1.  
Though the Dust Collector Accessory Kit is designed to offer a wide variety of appli-  
cations, the following illustration depicts a typical assembly method to hook-up one power  
equipment tool and two power equipment tools. (See Figure A, next page.)  
2.  
NOTE: The Dust Collector Accessory Kit is designed to be attached to stationary  
power equipment tools and dust collectors having 4” diameter dust ports. De-  
pending on the diameter of the dust port of your power equipment tools and dust  
collector, it may be necessary to attach size adapters (not provided) to ensure a  
proper fit.  
SKU 47911  
PAGE 4  
 
DUST HOOD (#3)  
OR  
TABLE SAW DUST HOOD (#5)  
BLAST GATE (#2)  
STEEL CLAMP (#6)  
POWER  
DUST  
TOOL  
PORT  
DUST  
PORT  
FLEXIBLE HOSE (#1)  
DUST  
COLLECTOR  
“Y” FITTING  
TO ATTACH TO  
ONE OR TWO  
POWER TOOLS  
FIGURE A  
INSPECTION, MAINTENANCE, AND CLEANING  
1.  
2.  
CAUTION: Prior to performing any inspection, maintenance, or cleaning on the  
Dust Collector Accessory Kit, make sure to disconnect the machine(s) to which  
the Accessory Kit is attached from its electrical power outlet.  
BEFORE EACH USE, inspect the general condition of the Dust Collector Acces-  
sory Kit. Check for loose connections, misalignment or binding of moving parts,  
cracked, torn, or broken parts, and any other condition that may affect its safe  
operation. If abnormal noise or vibration occurs, have the problem corrected  
before further use. Do not use damaged equipment.  
3.  
DAILY: With a soft brush, cloth, or vacuum, remove all debris from the Dust  
Collector Accessory Kit. If necessary, you may use a mild detergent.  
SKU 47911  
PAGE 5  
 
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY  
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR  
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT  
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS  
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTUER AND/OR  
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD  
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE  
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE  
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER  
INSTALLATION OF REPLACEMENT PARTS THERETO.  
PARTS LIST  
ꢋꢌꢆꢁꢍꢎ  
ꢃꢂꢄꢅꢆꢇꢈꢁꢇꢉꢊ  
0ꢌꢚꢈꢏ ꢔꢄꢔꢅꢌꢕꢌꢜ!.ꢌ'ꢁꢂꢑꢌꢐꢎꢔꢕꢈꢖꢎꢔꢌꢗꢁꢃꢔ  
0ꢌꢚꢈꢏ ꢔꢄꢔꢅꢌꢊꢎꢏꢃꢄꢌ+ꢏꢄꢔ  
/0ꢌꢚꢆꢃꢄꢌꢗꢁꢁ&  
/<0ꢌꢐꢈꢄꢄꢈꢂꢑ  
ꢜ*0ꢌ>ꢏꢖꢎꢔꢌꢋꢏꢞꢌꢚꢆꢃꢄꢌꢗꢁꢁ&  
0ꢌꢚꢁꢆꢖꢎꢔꢌꢘꢈꢅꢔꢌꢋꢄꢔꢔꢎꢌꢀꢎꢏ ꢙꢃ  
ꢏꢁꢐꢑ  
*
*
ꢜ!  
*
$
=
/
ASSEMBLY DIAGRAM  
1
6
2
5
3
4
SKU 47911  
PAGE 6  
 

Grizzly Paint Sprayer H7673 User Manual
Grizzly Sander G1183 User Manual
Grundig Stereo System CDC 477 User Manual
Haier Air Conditioner AP075M User Manual
Hamilton Beach Blender Classic Chrome Blender User Manual
Hans Grohe Plumbing Product 06128XX0 User Manual
Hasselblad Camera Lens H 17X User Manual
Havis Shields Camcorder Accessories KR 800 User Manual
Honeywell Welding System NXL User Manual
Hunter Fan Humidifier 31206 User Manual