StainleSS Steel Solar
lightS
Model 92122
Set up and operating inStructionS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS Manual.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
best results, the Lights should be
placed in an area that receives at
least eight hours of direct sunlight per
day.
SpeciFicationS
Battery
Ni-cd, AA 1.2V, 600mAh (included)
2 Stainless Steel Solar Lights
Included
4. Place a Spike onto a Connector and
then into the Shaft.
unpacKing
5. Push the unit firmly into the ground.
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please call
Harbor Freight Tools at the number shown
on the cover of this manual as soon as
possible.
6. The Solar Light can be placed on the
Shaft now.
7. Repeat these steps to assemble the
other light.
operating inStructionS
initial Set up
inStructionS
1. Allow the Light to charge for a full
day in direct sunlight, before first use.
note: The on/off switch must be in
the ON position when charging.
read all warning sections at the
beginning of this manual
including all text under
subheadings therein before set 2. The Solar Light will turn on
up or use of this product.
automatically when it gets dark, and
provide illumination for up to eight
hours.
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
3. Do not install the Solar Light near a
nighttime light source. A bright light
source will prevent the Light from
turning on at night.
1. Unscrew the lens of the Head
Fixture. Remove the four screws on
the bottom of the Fixture. Open the
battery compartment to verify that
battery polarity is correct. Be careful
not to pull on the wires connected to
the casing, damaging the wires will
render the unit dysfunctional. Close
the unit and replace the screws.
4. To store the unit, turn off the Light
and disconnect its power supply after
use. Clean, then store the Light
indoors out of children’s reach.
2. Push the power switch to the ON
position. Replace the lens.
3. Examine the area where the Solar
Light is to be placed. Make sure
there are no utility lines beneath the
surface that might be damaged. For
SKU 92122
For technical questions, please call 1-800-444-3353.
Page 3
shadow from trees, buildings, etc.
Make sure the lights are located in
an unobstructed location where they
can receive 8 hours of sunlight a day.
Allow the battery to recharge for 2 full,
sunny days. Overcast days will limit
performance.
Maintenance and SerVicing
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
cleaning, Maintenance, and lubrication
3. Dirty solar panel (on top of the Cap). A
dirty solar panel will not allow the unit
to charge and will shorten the life of the
battery. Use a soft, moist cloth to clean
the solar panel. Do not use bleaches or
detergents.
1. BeFore each uSe, inspect the
general condition of the tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical
wiring, and any other condition that
may affect its safe operation.
no light:
1. The On/Off switch may be in the OFF
position. Turn it to the ON position.
2. periodically, clean external surfaces
of the Light with clean, moist cloth.
For best operation, clean the Solar
Panel on the top of the Cap, so that
the battery will charge efficiently.
2. An external light source (i.e. streetlight,
porch light, flood light) may prevent
the light from automatically turning on
at night. Reposition the Solar Light.
Ensure the photocell of the solar light is
not affected by any other light sources.
3. Change the battery every year.
4. Dispose of the battery in a manner
consistent with State, Local and
Federal laws and regulations. Check
with your local hazardous waste
disposal facility for instructions.
3. Battery may need recharging. Check
the battery to ensure it is connecting
with the terminals.
trouBleShooting
pleaSe read the FolloWing
careFullY
The performance of solar light depends
on the amount of direct sunlight available
during daylight hours. If your solar light
The manufacturer and/or distributor has provided
the parts list and assembly diagram in this manual
does not operate properly, refer to possible as a reference tool only. Neither the manufacturer
or distributor makes any representation or warranty
of any kind to the buyer that he or she is qualified
reasons listed below:
to make any repairs to the product, or that he
or she is qualified to replace any parts of the
diM light:
product. In fact, the manufacturer and/or distributor
expressly states that all repairs and parts
1. The On/Off switch contacts may
be poor. Turn the switch on and off
several times to alleviate the problem.
replacements should be undertaken by certified
and licensed technicians, and not by the buyer.
The buyer assumes all risk and liability arising
out of his or her repairs to the original product or
replacement parts thereto, or arising out of his or
her installation of replacement parts thereto.
2. The battery may be low or under-
charged. Shadows will prevent the
solar panel from fully absorbing
sunlight, such as tree branches, any
SKU 92122
For technical questions, please call 1-800-444-3353.
Page 4
aSSeMBlY diagraM
partS liSt
part
description
Qty
1
2
3
4
Fixture
2
2
2
2
Shaft
Connector
Spike
record product’s Serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 92122
For technical questions, please call 1-800-444-3353.
Page 5
|