RIVER BOAT
WOODEN MODEL
ASSEMBLY INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
ASSEMBLY INSTRUCTIONS
1. Check the part numbers on the templates below to the drawing on Page 4. Mark each
with the corresponding number with a pencil to help organize. Lay out in numeric order
on a smooth surface after pressing out each piece with your thumb. (See Figure A-C)
#6
#12
#16
#13
#33
#40
#39
#17
#36
#32
#38
#34
#35
#22
#38
#37
#24
#1
#11
Figure B
Figure A
#21
#23
#18
#25
#26
#28
#27
#19
#7
#8
#10
#9
#30
#29
#2
#3
Figure C
PAGE 3
#4
#5
SKU 90139
2. Smooth the edges of the punched out pieces with sand paper. Begin putting together
by using the drawing below as a guide. Use glue on the portions shown in “black”.
See arrows in Figure D.
3. Use Scotch Tape® on the backside to hold round or non-flat pieces together.
4. A rubber band can be used to hold assembled pieces until glue has dried. Clean the
edges or surfaces of the Riverboat with a wet cloth to remove wet glue or
unsightly smudges.
5. Rod “A” passes through Paddle Wheels and frame, left to right of the Riverboat.
6. When assembly is completed, you can finish the Riverboat with paint, colored
markers or crayons using your creativity.
Assemble #’s 26, 30,
31- 35 into #12
#29
#30
#34 X 2
#26
#12
#27
#7
#32 X 2
#9
#34 X 2
#4
#6
#22 X 2
#10
#11 X 6
Put the rod through 19
and 20 assembly and
them put 23, 25 into 18.
#2
#38 X 2
#3
#1
#5
Tape the underside
of the round to hold
together.
#37 X 2
#36
#39 X 2
#36
#18 X 2
#24 X 2 X 2
#40 X 2
“A”
Brass Rod
#25 X 2
#23 X 8 X 2
#17 X 2
#19 X 2
#16 X 2
Assemble
#13
#21 X 2
Rod “A” through
#’s 21, 19, 23-25, 18,
17, 16, 13, left and
right.
Figure E
Figure D
SKU 90139
PAGE 4
PARTS LIST
PART #
DESCRIPTION
QTY
Templates-Scored Core-Wood
Glue (White) (not shown)
Sand Paper (2” X 2”)(not shown)
Axle Rod (not shown)
1
2
3
A
3
1
1
1
#1
#1
MAINTENANCE
1. For better and safer performance, keep all parts of this product clean and dry.
2. Periodically check to see that all hardware is in place.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
SKU 90139
PAGE 5
|