Harbor Freight Tools Motorcycle 94830 User Manual

LIFT EXTENSION WINGS  
(For Use With Model 94813 Motorcycle Lift)  
Model 94830  
ASSEMBLY INSTRUCTIONS  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
TO PREVENT SERIOUS INJURY,  
READ AND UNDERSTAND ALL WARNINGS  
AND INSTRUCTIONS BEFORE USE.  
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape of form  
without the express written consent of Harbor Freight Tools.  
For technical questions, please call 1-800-444-3353.  
 
2.  
Keep bystanders, children, and visitors away while assembling and using  
the Extension Wings. Distractions can cause you to lose control.  
PERSONAL SAFETY  
3.  
4.  
Stay alert. Watch what you are doing, and use common sense during use. Do  
not use the Motorcycle Lift while tired or under the influence of drugs, alcohol, or  
medication. A moment of inattention while operating power tools may result in  
serious personal injury.  
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or  
long hair can be caught in moving parts.  
5.  
6.  
Do not overreach. Keep proper footing and balance at all times. Proper footing  
and balance enables better control in unexpected situations.  
Always wear eye protection. Wear ANSI approved safety impact eye glasses,  
when using this product.  
TOOL USE AND CARE  
7.  
8.  
Store idle tools and equipment out of reach of children and other untrained  
people. Tools and equipment are dangerous in the hands of untrained users.  
Maintain this product with care. Keep this product clean. Properly maintained  
equipment is easier to control. Do not use damaged equipment. Tag damaged  
equipment “Do not use” until repaired.  
9.  
Check for misalignment or binding of moving parts, loose or broken parts,  
and any other condition that may affect this product’s operation. If dam-  
aged, have this product serviced before using. Many accidents are caused by  
poorly maintained tools and equipment.  
10.  
Use only accessories that are recommended by the manufacturer for your  
model. Accessories that may be suitable for one product may become hazard-  
ous when used on another product.  
SERVICE  
11.  
Product service must be performed only by qualified service technician.  
Service or maintenance performed by unqualified personnel could result in a risk  
of injury.  
SKU 94830  
For technical questions, please call 1-800-444-3353  
PAGE 3  
 
13.  
When servicing the Extension Wings, use only identical replacement parts.  
Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this  
manual. Use of unauthorized parts or failure to follow maintenance instructions  
may create a risk of injury.  
SPECIFIC SAFETY RULES  
1.  
2.  
The Lift Extension Wings are designed only for use with the model 94813  
Motorcycle Lift (available from Harbor Freight Tools).  
WARNING! Do not exceed the 1,200 pound maximum lifting capacity  
of this product. Exceeding the maximum lifting capacity could cause personal  
injury and/or property damage. Beware of dynamic loading! Suddenly drop-  
ping a load onto this product may create, for a brief instant, an excess load which  
may result in damage to the product and/or personal injury.  
3.  
4.  
Industrial applications must follow OSHA requirements.  
Store idle tools. When not in use, store the Extension Wings in a clean, dry,  
safe location out of reach of children.  
5.  
6.  
7.  
Prior to using this product, make sure to read and understand all instruc-  
tions and safety precautions as outlined in the model 94813 Motorcycle Lift  
manual.  
Make sure any load being supported by the Extension Wings is well bal-  
anced. Unbalanced loads may cause the lift to tip over, potentially causing  
serious personal injury and/or property damage.  
Always make sure the object being lifted is properly and safely secured  
prior to raising the object.  
8.  
9.  
Always monitor the object being lifted so it does not rock back and forth.  
WARNING! The warnings and cautions discussed in this manual cannot  
cover all possible conditions and situations that may occur. It must be under-  
stood by the operator that common sense and caution are factors which cannot  
be built into this product, but must be supplied by the operator.  
SAVE THESE INSTRUCTIONS  
SKU 94830  
For technical questions, please call 1-800-444-3353  
PAGE 4  
 
ASSEMBLY INSTRUCTIONS  
NOTE:  
For further references to the parts mentioned in the following pages,  
see the Assembly Diagram on page 9 of this manual.  
Attach The Side Extensions To The Motorcycle Platform:  
5
1
5
3
8
12  
8
12  
13  
14  
5
13  
14  
6
7
12  
5
2
12  
13  
6
14  
13  
7
14  
4
FIGURE A  
1.  
2.  
3.  
4.  
With assistance, align the mounting hole in each end of the Left Side Extension  
(2) with the mounting hole in each end on the left side of the Platform.  
Insert two Extension Panel Pipes (8) through the Left Side Extension (2) and the  
Motorcycle Platform.  
With assistance, slide the Right Side Extension (1) onto the Extension Panel  
Pipes (8) and up against the Motorcycle platform.  
Insert a Bolt (5) through each end of the two Extension Panel Pipes (8). Then  
secure the Extension Panel Pipes in place, using the Washers (6) and Nuts (7)  
provided.  
SKU 94830  
For technical questions, please call 1-800-444-3353  
PAGE 5  
 
Attach The Ramp Extensions To The Motorcycle Ramp:  
1.  
With assistance, insert the hook on the Left Ramp Extension (4) into the mount-  
ing hole in the end of the Left Side Extension (2). (See Figure A.)  
2.  
Align the two mounting holes under the Left Ramp Extension (4) with the two  
mounting holes in left side of the Ramp. Then secure the Left Ramp Extension to  
the Ramp, using two Bolts (12), two Washers (13), and two Nuts (14).  
(See Figure A.)  
3.  
Align the two mounting holes in the Right Ramp Extension (3) with the two  
mounting holes in the right side of the Ramp. Then secure the Right Ramp Ex-  
tension to the Ramp, using two Bolts (12), two Washers (13), and two Nuts (14).  
(See Figure A.)  
Attach The Stabilizer Bar To The Motorcycle Lift Frame:  
1.  
Insert the Stabilizer Bar (11) through the bottom/front frame of the Motorcycle  
Lift. (See Figure B.)  
2.  
Align the two innermost mounting holes under the Stabilizer Bar (11) with the two  
mounting holes in the bottom/front frame of the Motorcycle Lift. Then secure the  
Stabilizer Bar to the frame, using two Pins (10). (See Figure B.)  
3.  
Slide a Pipe Cap (9) onto each end of the Stabilizer Bar (11). Then secure the  
Pipe Caps to the Stabilizer Bar, using one Pin (10) for each Pipe Cap.  
(See Figure B.)  
10  
9
10  
11  
10  
10  
FIGURE B  
9
SKU 94830  
For technical questions, please call 1-800-444-3353  
 
PAGE 6  
OPERATING INSTRUCTIONS  
1.  
WARNING! Do not exceed the maximum lifting capacity of the Exten-  
sion Wings (1,200 pounds). Exceeding the maximum lifting capacities could  
cause personal injury and/or property damage.  
2.  
3.  
WARNING! Follow all instructions and safety precautions as outlined in the  
model 94813 Motorcycle Lift manual.  
Make sure the Platform of the Motorcycle Lift is fully collapsed to the floor. Also,  
make sure the Removable Plate of the Motorcycle Lift is properly positioned over  
the inspection hole of its Platform.  
4.  
5.  
With assistance, roll the object to be raised up the Right and Left Ramp Exten-  
sions (3, 4) and onto the Right and Left Side Extensions (1, 2).  
You should stabilize the object using tie-down straps (not included) on each side  
of the motorcycle with one end of the straps tied to the object and the other end  
of the straps tied to the Right and Left Side Extensions (1, 2).  
6.  
7.  
8.  
9.  
Connect an air hose to the Motorcycle Lift’s Foot Air Valve. Then set the air  
compressor’s regulator between 100 and 120 PSI. Do not exceed 120 PSI.  
Step on and hold down the right side of the Motorcycle Lift’s Foot Air Valve to  
raise the Lift.  
When the Motorcycle Lift has been raised to the working height, lower its Safety  
Bar completely to prevent the Lift from accidentally lowering.  
When work on the motorcycle is completed, check under the Motorcycle Lift to  
make sure there are no tools, parts, etc. and that it is safe to lower  
the Lift.  
10.  
11.  
12.  
Remove the Safety Bar. Then step on and hold down the left side of the Motor-  
cycle Lift’s Foot Air Valve to slowly lower the Lift to the floor.  
With assistance, remove the tie-down straps from the object. Then, slowly back  
the object completely off the Motorcycle Lift.  
Turn off the air compressor. Step on and hold down the left side of the Motor  
cycle Lift’s Foot Air Valve to release any remaining compressed air in the system.  
Then, disconnect the compressor’s air hose from the Foot Air Valve.  
13.  
Make sure to store the Motorcycle Lift and its Extension Wings in a clean, dry,  
safe location out of reach of children and other unauthorized people.  
SKU 94830  
For technical questions, please call 1-800-444-3353  
PAGE 7  
 
INSPECTION, MAINTENANCE, AND CLEANING  
1.  
Before each use: Inspect the general condition of the Extension Wings. Check  
for cracked, worn or damaged parts, loose or missing parts, and any other  
condition that may affect the product’s safe operation. If a problem occurs, have  
the problem corrected before further use.  
Do not use damaged equipment.  
2.  
3.  
4.  
To clean: Use a damp cloth and a mild detergent. Do not use solvents or other  
flammable agents.  
When storing: Keep the Extension Wings in a clean, dry, safe location out of  
reach of children and other unauthorized people.  
CAUTION! All maintenance, service, and repairs not discussed in this  
manual should only be performed by a qualified service technician.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS LIST AND  
ASSEMBLY DIAGRAM INTHIS MANUAL AS A REFERENCETOOL ONLY. NEITHERTHE  
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY  
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY  
PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR  
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD  
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY  
THE BUYER. THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF  
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS  
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT  
PARTS THERETO.  
SKU 94830  
For technical questions, please call 1-800-444-3353  
PAGE 8  
 
PARTS LIST AND ASSEMBLY DIAGRAM  
Part  
1
2
3
4
5
6
7
Description  
Side Extension (Right)  
Side Extension (Left)  
Ramp Extension (Right)  
Ramp Extension (Left)  
Bolt  
Qty.  
1
1
1
1
4
4
4
Part  
8
9
10  
11  
12  
13  
14  
Description  
Extension Panel Pipe  
Pipe Cap  
Pin  
Stabilizer Bar  
Bolt  
Qty.  
2
2
4
1
4
4
4
Washer  
Nut  
Washer  
Nut  
1
2
5
5
6
6
7
5
8
6
7
7
5
8
6
3
7
10  
10  
10  
9
10  
11  
4
9
12: Bolt not shown.  
13: Washer not shown.  
14: Nut not shown.  
NOTE:  
Some parts are listed and shown for illustration purposes only,  
and are not available individually as replacement parts.  
SKU 94830  
For technical questions, please call 1-800-444-3353  
PAGE 9  
 

Grizzly Automobile Parts G2909 User Manual
Grizzly Saw Model G0536 User Manual
Hand Held Products Laptop Dolphin 7400 User Manual
Harbor Freight Tools Automobile Accessories 96658 User Manual
Harbor Freight Tools Paint Sprayer 91009 User Manual
Honeywell Satellite Radio 5800MICRA User Manual
Honeywell Thermostat AQ1000TP2 User Manual
Hotpoint Washer WM33 User Manual
Huawei Cell Phone 616960034704 User Manual
Igloo Refrigerator FR280 User Manual