Harbor Freight Tools Picnic Table 97736 User Manual

COMBINATION  
PICNIC TABLE - BENCH  
Model 97736  
AssEMBLy & sET-UP INsTrUCTIONs  
Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
Distributed exclusively by Harbor Freight Tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
read this material before using this product.  
Failure to do so can result in serious injury.  
sAVE THIs MANUAL.  
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions or replacement parts, please call 1-800-444-3353.  
 
7.  
8.  
Never allow people or animals to stand  
or climb on this product.  
AssEMBLy  
Pinch point warning: Use caution to  
avoid pinching fingers when assembling  
and setting up this unit.  
Note: For additional information regarding the  
parts listed in the following pages, refer to the  
accompanying illustrations.  
9.  
Adults only should perform the assembly  
and set-up of this product.  
1.  
Attach the two Folding Beams (2) flush to  
the inner side of the Table Top (5), using  
six Bolts each with two Washers and one  
Nut (9). (see Figure A.)  
10. When in use, make sure all Legs of the  
product are flat on the ground.  
2.  
NOTE: The Bolts and Washers (9)  
should be inserted from the outside of  
the Table Top (5) into the Folding Beams  
(2). (see Figure A.)  
11. The warnings, precautions, and  
instructions discussed in this instruction  
manual cannot cover all possible  
conditions and situations that may occur.  
It must be understood by the operator  
that common sense and caution are  
factors which cannot be built into this  
product, but must be supplied by the  
operator.  
FIGUrE A  
TABLE TOP (5)  
sAVE THEsE  
FOLDING BEAM (2)  
INsTrUCTIONs.  
BOLTs, WAsHErs, NUTs (9)  
sPECIFICATIONs  
3.  
4.  
Place and align the Short Bench Top (8)  
flush on the two Bench Supports (4).  
(see Figure B.)  
Unfinished Fir  
Construction  
Yellow/Green Zinc Plated Steel Bolts,  
Material  
Washers, Nuts, and Screws  
400 Pounds Total  
Weight Capacity  
(Distributed Evenly)  
Fasten the eight Screws (11) into the  
pre-drilled holes on the Short Bench  
Top (8) to the Bench Supports (4). (see  
Figure B.)  
Umbrella Hole  
1-5/8”  
Diameter  
Waterproof  
No  
Water Resistant  
sCrEWs (11)  
FIGUrE B  
UNPACkING  
sHOrT  
BENCH  
TOP  
When unpacking, check to make sure that  
the item is intact and undamaged. If any parts  
are missing or broken, please call Harbor Freight  
Tools at the number shown on the cover of this  
manual as soon as possible.  
BENCH sUPPOrT (4)  
(8)  
SKU 97736  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
5.  
6.  
Turn the assembled Bench upside down. 10. Hold the Table securely in its standing  
position.  
Position the Diagonal Supports (7) so  
one end is against the longer cross  
beam of Bench Support (4) legs. Then  
align the other end so it is flush to the  
wood edge next to the center gap of the  
Short Bench Top (8). The two Diagonal  
Supports (7) need to be attached at  
opposite sides of the bench gap, using  
three Screws (11) per Support. (i.e., one  
support will be attached to one bench  
slat, and the other bench slat will be  
attached to the other bench support.  
(see Figure C.)  
11. Attach the two Table Legs (1) to the  
Table Top (5) by inserting two Bolts  
each, with four Washers and one Nut  
(10) into the pre-drilled hole at the  
rounded end of the Table Legs. NOTE:  
One pre-drilled hole still remains below  
the Table Legs. (see Figure E.)  
TABLE TOP (5)  
7.  
NOTE: There are no pre-drilled holes  
for the Screws (11) in the bench slat  
or Bench Supports (4). Instead, there  
are guide marks in the wood to indicate  
where the Screws must be inserted.  
TABLE LEG  
(1)  
BOLTs, WAsHErs, NUTs (10)  
(see Figure C.)  
BENCH  
FIGUrE E  
sUPPOrT  
DIAGONAL  
sUPPOrT  
(4)  
12. Attach the two Arm Rests (3) to the Table  
Legs (1), using two Bolts, each with four  
Washers and one Nut (10). (see Figure  
F.)  
(7)  
sHOrT  
BENCH  
TOP (8)  
FIGUrE C  
FIGUrE F  
TABLE LEG (1)  
8.  
9.  
Set the Table on its side.  
Attach the Folding Beams (2) to the  
outside edge of the Bench Supports (4),  
using two Bolts, each with four Washers,  
and one Nut (10).  
BOLTs  
WAsHErs  
NUTs  
ArM  
rEsT  
(3)  
(see Figure D.)  
(10)  
13. Place the Long Bench Top (6) on the  
Table Legs (1). Make sure the longer  
bar underneath the Long Bench top is  
toward the outside.  
(see Figure G.)  
14. Fasten the eight Screws (11) into the  
pre-drilled holes in the Long Bench Top  
(6) to the Table Legs (1).  
FOLDING BEAM (2)  
BOLTs, WAsHErs, NUTs (10)  
FIGUrE D  
(see Figure G.)  
SKU 97736  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
LONG  
BENCH  
TOP  
FIGUrE G  
sCrEWs (11)  
INsPECTION AND  
MAINTENANCE  
(6)  
1.  
2.  
PErIODICALLy, inspect the general  
condition of the Picnic Table/Bench.  
Check for loose connections, improper  
weight distribution, and any other  
condition that may affect the product’s  
operation.  
TABLE LEG  
(1)  
15. To transform the Picnic Table into a  
Bench, simply lift up the Table Top (5)  
and Arm Rests (3).  
TO CLEAN, use a damp cloth with a  
mild detergent. Then dry. Do not use  
solvents.  
(see Figures H, I, and J.)  
PLEAsE rEAD THE  
FOLLOWING CArEFULLy  
THE MANUFACTURER AND/OR DISTRIBUTOR  
HASPROvIDEDTHEPARTSLISTANDASSEMBLY  
DIAGRAM IN THIS MANUAL AS A REFERENCE  
TOOLONLY. NEITHERTHEMANUFACTUREROR  
DISTRIBUTOR MAKES ANY REPRESENTATION  
OR WARRANTY OF ANY KIND TO THE BUYER  
THAT HE OR SHE IS qUALIFIED TO MAKE ANY  
REPAIRS TO THE PRODUCT, OR THAT HE OR  
SHE IS qUALIFIED TO REPLACE ANY PARTS OF  
THE PRODUCT. IN FACT, THE MANUFACTURER  
AND/OR DISTRIBUTOR ExPRESSLY STATES  
THATALLREPAIRSANDPARTSREPLACEMENTS  
SHOULD BE UNDERTAKEN BY CERTIFIED AND  
LICENSED TECHNICIANS, AND NOT BY THE  
BUYER. THE BUYER ASSUMES ALL RISK AND  
LIABILITYARISINGOUTOFHISORHERREPAIRS  
TOTHEORIGINALPRODUCTORREPLACEMENT  
PARTS THERETO, OR ARISING OUT OF HIS OR  
HER INSTALLATION OF REPLACEMENT PARTS  
THERETO.  
FIGUrE H  
LIFT UPWArDs  
FIGUrE I  
FIGUrE J  
16. IMPOrTANT: To extend the life of this  
Picnic Table/Bench, it is recommended  
that you thoroughly coat it with an  
appropriate protectant (i.e., paint,  
varnish, etc.).  
SKU 97736  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
PArTs LIsT & AssEMBLy DIAGrAM  
Part #  
Description  
Table Leg  
Qty.  
2
Part #  
Description  
Diagonal Support  
Qty.  
2
1
2
3
4
5
6
7
8
Folding Beam  
Arm Rest  
2
Short Bench Top  
1
2
9
Bolt w/Two Washers & One Nut  
Bolt w/Four Washers & One Nut  
Screw  
6
Bench Support  
Table Top  
2
10  
11  
6
1
22  
Long Bench Top  
1
2
1
3
4
9
5
10  
11  
7
6
8
SKU 97736  
For technical questions, please call 1-800-444-3353.  
Page 6  
 
LIMITED 90 DAy WArrANTy  
Harbor Freight Tools Co. makes every effort to assure that its products meet high  
quality and durability standards, and warrants to the original purchaser that this product  
is free from defects in materials and workmanship for the period of 90 days from the date  
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,  
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,  
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event  
be liable for death, injuries to persons or property, or for incidental, contingent, special  
or consequential damages arising from the use of our product. Some states do not allow  
the exclusion or limitation of incidental or consequential damages, so the above limitation  
of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL  
OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF  
MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us with  
transportation charges prepaid. Proof of purchase date and an explanation of the complaint  
must accompany the merchandise. If our inspection verifies the defect, we will either  
repair or replace the product at our election or we may elect to refund the purchase price  
if we cannot readily and quickly provide you with a replacement. We will return repaired  
products at our expense, but if we determine there is no defect, or that the defect resulted  
from causes not within the scope of our warranty, then you must bear the cost of returning  
the product.  
This warranty gives you specific legal rights and you may also have other rights which  
vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
record Product’s serial Number Here:  
Note: If product has no serial number, record month and year of purchase instead.  
Note: Some parts are listed and shown for illustration purposes only, and are not  
available individually as replacement parts.  
SKU 97736  
For technical questions, please call 1-800-444-3353.  
Page 7  
 

Graco Music Mixer 224854 Series D User Manual
Gravely Lawn Mower 89201800 User Manual
Greenheck Fan Ventilation Hood GGH20 User Manual
Haier Air Conditioner HW 18L2H User Manual
Hamilton Beach Toaster All Metal Toasters User Manual
Harbor Freight Tools Washer 35740 User Manual
Harman Kardon Stereo Receiver AVP1A User Manual
Hearth and Home Technologies Stove 3500L User Manual
Hotpoint Oven MG23N H User Manual
Hotpoint Washer Wml 721 User Manual