PNEUMATIC PLANISHING HAMMER
94847
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may
differ slightly from the product described herein.
Distributed Exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
8.
9.
Do not overreach. Keep proper footing and balance at all times. Do not reach over
or across running machines.
Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect
tool cords periodically and, if damaged, have them repaired by an authorized
technician. The handles must be kept clean, dry, and free from oil and grease at all
times.
10.
11.
Disconnect air supply. Unplug tool from air supply when not in use.
Remove adjusting keys and wrenches. Check that keys and adjusting wrenches
are removed from the tool or machine work surface before operation.
12.
13.
Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment and binding of moving parts; any broken
parts or mounting fixtures; and any other condition that may affect proper operation.
Any part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the tool if any switch does not turn On and Off properly.
14.
Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are available from
Harbor Freight Tools.
15.
16.
Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
Maintenance. For your safety, service and maintenance should be performed
regularly by a qualified technician.
17.
18.
Compressed air only. Never use combustible gas as a power source.
Protect hands and body from injuries. Always wear leather gloves and body
protection when handling metal for use on the Planishing Hammer. Keep hands,
fingers, and arms away from the hammer head and anvil during operation.
19.
Install this product on a proper surface. Locate on a flat, level, and solid surface
that is capable of supporting the weight of the Planishing Hammer and the material
being hammered.
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which cannot
be built into this product, but must be supplied by the operator.
Page 3
SKU 94847
For technical questions, please call 1-800-444-3353
Unpacking
When unpacking, check to make sure the following parts are included. Refer to the Parts
List and Assembly Drawing located at the end of this manual. If any parts are missing or
broken, please call Harbor Freight Tools at the number on the cover of this manual as soon
as possible.
Regulator (11)
Air Hammer (10)
Screw (2)
Hammer Head (3)
Anvil (5)
Adjustable Pole (7)
Air Hose (12)
Stopper Pin (9)
Range Adjust Block (6)
Switch Assembly (13)
Mounting Holes (Qty. 4)
Installation
Mounting “C” Frame
1.
Select a workbench in the shop area able to support the weight of the Planishing
Hammer, the metal being worked on, and the vibration of the planishing process.
2.
Mount the “C” Frame (1) to the workbench using hardware (not supplied).
The “C” Frame should be positioned so that the mounted Air Hammer (10) is
extended slightly over the edge of the workbench. This will accommodate various
shapes of metals being planished. Hardware should consist of nuts, bolts, flat
washers, and lock washers.
Note: There is an entry hole on the side of “C” Frame (1) where sand can be inserted to
reduce noise and vibration.
Air Connection
1.
Attach a Union fitting (not supplied) into the Switch Assembly Inlet (13) fitting.
A Union fitting is necessary before a connection can be made to an Air Compressor.
2.
For easy connection or removal, attach an Air Coupler (not supplied) to the Union
fitting, if quick-coupling is desired.
3.
Retighten all couplings and fittings.
4.
Attach the Air Hose (not supplied) from the Air Compressor (not supplied) to the
Switch Assembly (13). Place Switch Assy on the floor next to the Planishing Hammer.
Page 4
SKU 94847
For technical questions, please call 1-800-444-3353
Caution: Do not turn on the Air Compressor at this time.
Oiler and Filter Connection
Dirt, water, and the lack of pneumatic tool oil are major causes for tool wear. Install an
optional oiler-filter (not supplied), as illustrated below for better performance.
Connect the air tool, air hoses, filter, and oiler to the Compressor Air Outlet as
illustrated below. Use pipe thread seal or Teflon tape on all threaded connections.
The filter and oiler (not supplied) are recommended but not mandatory for operation.
If the filter and oiler are not used, connect the air hose directly to the 1/4 inch, 18 NPT
connector located at the Air Switch Assembly Inlet (13) fitting. Also, a few drops of
pneumatic tool oil must be added through the air line before each use.
Mounting Air Hammer to “C” Frame
1.
Unscrew Screw (2) so it is out of the way of the Air Hammer (10) when inserting it
into the “C” Frame. Do not remove Screw (2). See photo below, right.
Air Hammer (10)
Hammer Head (3)
“C” Frame
Coil Spring
Hammer Sleeve (4)
Screw (2)
Anvil (5)
2.
Screw off the Coil Spring from the Air Hammer (10) and slip it off, along with the
Hammer Head (3) and Hammer Sleeve (4). See photo below, left.
3.
4.
5.
Slide the Air Hammer body into the “C” Frame mounting hole as shown below, right.
Insert the desired size Anvil (5) onto the Adjustable Pole (7).
Place the Hammer Head (3) through the Coil Spring, then into the Air Hammer.
Screw on the Coil Spring until it stops.
6.
Retighten Screw (2) completely.
Page 5
SKU 94847
For technical questions, please call 1-800-444-3353
Operation
1.
2.
To change the height of the Anvil (5) to within 1-1/2 inches of the desired height,
pull out Stopper Pin (9), and move the Adjustable Pole (7) up or down to one of two
Stopper Pin holes. Replace Stopper Pin.
To adjust closer to the desired height, move the Range Adjust Block (6) to the right or
left to reach the desired height.
3.
4.
Turn on the Air Compressor and set its regulator to 90 PSI.
Before planishing, test the operation by pressing down on the foot Switch Assy (13)
with your foot.
5.
6.
Adjust the cycle speed of the Air Hammer by turning the Regulator (11) valve
clockwise or counterclockwise.
Use both gloved hands to hold the material to be planished and place it between the
Anvil (5) and the Hammer Head (3).
7.
8.
Press down on the Switch Assy (13) on the floor with your foot to operate.
When finished planishing, remove your foot from the Switch Assy, and wait for the Air
Hammer to stop completely.
9.
Turn the Air Compressor off.
10. Press down on the Switch Assy (13) again to release any remain air pressure in the
Air Hammer.
Changing Anvils
1.
Unscrew Screw (2) so it is out of the way of the Air Hammer (10) when removing it
from the “C” Frame. Do not remove Screw (2). See photo on page 5, bottom-right.
2.
Screw off the Coil Spring from the Air Hammer (10) and slip it off, along with the
Hammer Head (3) and Hammer Sleeve (4). See photo on page 5, bottom-left.
3.
4.
5.
Slide the Air Hammer body out of the “C” Frame mounting hole.
Replace Anvil (5) with desired size onto the Adjustable Pole (7).
Replace the Air Hammer into the “C” Frame. Then, attach the Hammer Head (3)
through the Coil Spring, then into the Air Hammer. Screw on the Coil Spring until it
stops.
6.
Retighten Screw (2) completely.
Troubleshooting
Problem
Probable Cause
Solution
Planishing Hammer does not
operate when Switch pressed
Planishing Hammer operates
at diminished pressure
No air pressure in air line
Check air line and compressor
Air pressure below normal
operating pressure
Check regulator on
compressor and Air Hammer
Page 6
SKU 94847
For technical questions, please call 1-800-444-3353
Maintenance
1.
2.
After each use, wipe all components of the Planishing Hammer with a clean cloth to
remove any dirt and grease buildup.
To maintain tool life, always lubricate the air line by adding a few drops of pneumatic
tool oil to the air line (or Air Inlet) before each use. Or, install the automatic oiler-filter
system as illustrated on page 5.
3.
4.
Before each use, drain water out of the air compressor tank and condensation from
the air lines. Refer to the Air Compressor Operation Manual.
Cover the Planishing Hammer and keep in a clean and dry location.
Parts List
Part
1
Description
“C” Frame
Qty.
1
1
2
Screw
1
1
3
1
1
1
3
4
5
6
7
8
Hammer Head
Hammer Sleeve
Anvil (small, medium, large)
Range Adjust Block
Adjustable Pole
Screw
1
9
Stopper Pin
1
1
1
1
1
1
1
1
10
11
12
13
14
15
16
17
18
19
Air Hammer
Regulator
Air Hose
Switch Assembly
Cover
Quick Connector (male)
PVC Air Hose
Male Thread Fitting
Hose Clamp
2
4
Screw
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANSAND NOT BYTHE BUYER. THE BUYERASSUMESALLRISKAND LIABILITYARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 7
SKU 94847
For technical questions, please call 1-800-444-3353
Assembly Drawing
Page 8
SKU 94847
For technical questions, please call 1-800-444-3353
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase. This
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or
accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to
you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either repair or
replace the product at our election or we may elect to refund the purchase price if we cannot
readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not
within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Page 9
SKU 94847
For technical questions, please call 1-800-444-3353
|