CORDLESS SCREWDRIVER SET
3.6 VOLT RECHARGABLE
91332
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
5. Use the right tool for the job. Do not attempt to force a small tool or
attachment to do the work of a larger industrial tool.There are certain
applications for which this tool was designed. It will do the job better and
more safely at the rate for which it was intended. Do not modify this tool and
do not use this tool for a purpose for which it was not intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be caught
in moving parts. Protective, electrically non-conductive clothes and non-skid
footwear are recommended when working. Wear restrictive hair covering to
contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety
goggles.
8. Do not overreach. Keep proper footing and balance at all times. Do not
reach over or across running machines.
9. Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and, if damaged, have them repaired by an
authorized technician.The handles must be kept clean, dry, and free from oil
and grease at all times.
10. Disconnect power. Unplug Charger Adapter when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting
wrenches are removed from the tool or machine work surface before
operating tool.
12. Avoid unintentional starting. Be sure the switch is in the Off position when
not in use and before plugging in. Do not carry any tool with your finger on
the trigger.
13. Stay alert. Watch what you are doing, use common sense. Do not operate
any tool when you are tired.
15. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for alignment and binding
of moving parts; any broken parts or mounting fixtures; and any other
condition that may affect proper operation. Any part that is damaged should
be properly repaired or replaced by a qualified technician. Do not use the tool
if any switch does not turn On and Off properly.
16. Guard against electric shock. Prevent body contact with electrical circuits
when using this tool.
SKU 91332 Download from Www.SomanuPalsa.cgoem3. All Manuals Search And Download.
17. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are
available from Harbor Freight Tools.
18. Do not operate tool if under the influence of alcohol or drugs. Read
warning labels if taking prescription medicine to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, do not operate
the tool.
19. Maintenance. For your safety, service and maintenance should be
performed regularly by a qualified technician.
20. People with pacemakers should consult their physician(s) before using
this product. Electromagnetic fields in close proximity to a heart pacemaker
could cause interference to or failure of the pacemaker.
In addition, people with pacemakers should adhere to the following:
♦ Avoid operating power tools alone.
♦ Don’t use a power tool with the power switch locked on.
♦ Properly maintain and inspect all tools before use to avoid electrical shock.
Note:Performance of this tool may vary depending on variations in battery power.
Warning:The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are fac-
tors which cannot be built into this product, but must be supplied by the opera-
tor.
Unpacking
When unpacking, check to make sure the that all following parts are included. If
any parts are missing or broken, please call Harbor Freight Tools at the number on
the cover of this manual.
Cordless
Screwdriver
Accessory Bits
and Adapters
Charger
Adapter
SKU 91332 Download from Www.SomanuPalsa.cgoem4. All Manuals Search And Download.
Operation
Battery Precautions
1. To avoid accidents, only charge the supplied batteries. Do not use a different
charger adapter with this tool.
2. Do not expose the battery to rain or wet conditions.
3. To avoid damage of cable and plug, never pull the cable to disconnect the
charger.
4. Do not charge the battery if either the cable or plug are damaged.
5. Repairs should be carried out by a qualified technician only.
6. Do not touch the battery poles with any conductive source.
7. Do not store the battery in a box with other metal objects.
8. Do not throw the battery in a fire.
Charging the Battery
The internal Battery does not come charged from the factory. Charge before
using.
1. Insert the Charger Adapter module plug into the unit connector as shown
below.
Note: Never over-discharge a battery by using the tool
even after tool performance is decreasing. Severe heat
is most destructive to a battery; the more heat
generated, the faster the battery loses power.
A battery that gets too hot can be permanently
damaged. Never attempt to discharge a tool’s
battery by continuing to pull the tool trigger.
When tool performance begins to diminish, stop
the tool and re-charge the battery for optimal performance.
2. Plug the Charger Adapter module into an electrical outlet.
The red LED on the cordless Screwdriver will light. Charge the new battery
from 5 to 7 hours. Battery usage time will ramp up as the new Battery is
used, and recharged. Do not overcharge the battery.
Caution: Never charge Battery for more than 7 hours continuously. Charger
Adapter should not be left plugged in or charging for more than 7 hours.
SKU 91332 Download from Www.SomanuPalsa.cgoem5. All Manuals Search And Download.
3. Remove the Power Adapter from the electrical outlet and store in the
Blowmold case.
Using the Cordless Screwdriver
1. Set the Screwdriver handle grip style by pressing on the Grip Button Lock
and turning the handle for pistol or straight grip.
Accessory Bit,
Rocker Switch
Driver, or Adapter
(Forward / Reverse)
Chuck (1)
Pistol Grip
Chuck (1)
Accessory Bit,
Driver, or Adapter
Straight Grip
Grip Button Lock
2. Insert the desired bit, driver, or adapter into the Chuck (1).
3. Engage the bit, driver, or adapter over the item being turned.
4. Press forward on the Rocker Switch for turning clockwise.
5. Press backward on the Rocker Switch for turning counterclockwise.
Maintenance
1. When finished using the Screwdriver, place it in the Blowmold case along
with all the accessories.
2. Store in a clean and dry location.
3. Recharge the batteries once a month whether used or not.
SKU 91332 Download from Www.SomanuPalsa.cgoem6. All Manuals Search And Download.
Parts List
Item #
1.
Description
Chuck
2.
3.
4.
5.
6.
7.
Screwnail
Screwnail
Enclosure (A)
Screwnail
Enclosure (right)
Switch
8.
9.
Limit Block
Bearing
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
Limit Box
Enclosure (B)
Heat-loss Block
Gear
Steering Stem
Gear
Gear
Motor
Enclosure (left)
Battery
Charger Adapter
NOTE: Some parts are listed and
shown for illustration purposes only
and are not available individually as
replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 91332 Download from Www.SomanuPalsa.cgoem7. All Manuals Search And Download.
Assembly Drawing
SKU 91332 Download from Www.SomanuPalsa.cgoem8. All Manuals Search And Download.
|