Harbor Freight Tools Security Camera 95154 User Manual

IMITATION DOME CAMERA With LED  
95154  
ASSEMBLY AND OPERATING INSTRUCTIONS  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SaVe thiS manual.  
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight  
Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual  
product may differ slightly from the product described herein. Tools required for assembly and service may not  
be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Revised Manual 09k  
 
8.  
9.  
Stay alert. Watch what you are doing, use common sense. Do not install the Imitation  
Dome Camera when you are tired.  
check for damaged parts. Before using the Imitation Dome Camera, any part that  
appears damaged should be carefully checked to determine that it will operate properly  
and perform its intended function. Check for alignment and binding of moving parts;  
any broken parts or mounting fixtures; and any other condition that may affect proper  
operation.Any part that is damaged should be properly repaired or replaced by a qualified  
technician. Do not use the Imitation Camera Dome if the power switch does not turn the  
Camera Dome on and off properly.  
10. Replacement parts and accessories. When servicing, use only identical replacement  
parts. Use of any other parts will void the warranty. Only use accessories intended for  
use with this product. Approved accessories are available from Harbor Freight Tools.  
11. do not install the imitation dome camera if under the influence of alcohol or drugs.  
Read warning labels if taking prescription medicine to determine if your judgment or  
reflexes are impaired while taking drugs. If there is any doubt, do not install the unit.  
12. only use 1.5V dc aa-Batteries. Always properly dispose of used batteries in accordance  
to the guidelines for waste disposal in your community.  
the warnings, precautions, and instructions discussed in this instruction manu-  
al cannot cover all possible conditions and situations that may occur. it must be  
understood by the operator that common sense and caution are factors which  
cannot be built into this product, but must be supplied by the operator.  
13.  
14.  
WaRning: All batteries must be disposed of properly. Do not incinerate. Batteries  
may burst, causing personal injury and/or property damage. Dispose of the used bat-  
teries properly, as cadmium in the batteries is toxic. For disposable guidelines, check  
with your local waste management guidelines in your community.  
unpacKing  
When unpacking, check to make sure that the product is intact and undamaged. If any  
part are missing or broken, please call Harbor Freight Tools at: 1-800-444-3353  
BatteRy inStallation  
1.  
2.  
First, remove the battery cover by pressing in on the upper lip of the cover then pull it  
out.  
Next place two AA 1.5 VDC Batteries in the Battery Housing. Be sure that the polari-  
ties (+ or -) of the batteries line up with the polarity signs in the battery housing. Finally  
replace the battery cover. See Figure 1 on page 4.  
SKU 95154  
For technical questions, please call 1-800-444-3353  
Page 3  
 
cameRa inStallation  
1.  
2.  
Chose a wall or ceiling location that allows you to mount the unit onto a solid surface  
capable of sustaining the weight of the unit. It is recommended that you choose a location  
that is out of the reach of pedestrians. If you cannot mount the camera to a wall stud, you  
will need to use the Dry Wall Mounting Anchors and Wood Screws (both not included).  
It is essential to proper mounting that you use the correct size screws and that you also  
space the two screw correctly. The exact distance between the two screws is 2.659”  
(67.59 mm) center to center. You can make a pattern of the mounting holes by placing  
a piece of tracing paper over the back of the Imitation Dome Camera and trace the  
mounting holes location using a pen or pencil. Next tape the pattern over the area that  
you want to install the camera. Mark the center of each mounting hole by hammering  
a nail through the pattern into the mounting surface. Attach the screws to the mounting  
surface leaving about a 1/4” of the screws’ shanks exposed.  
Warning: When mounting, be sure to avoid hammering into any electrical wiring.  
3.  
After the two mounting screw have been attached to the wall or ceiling, place the two  
mounting holes on the camera over the screw heads. Press the Dome Camera over the  
screw heads and twist the camera. This should secure it into place. Always be careful,  
when drilling into a wall or ceiling, to avoid wires, pipe or cables that may be in the path  
of the drill. Be aware that the Camera needs to be mounted securely so it will not fall off  
the mounting and cause bodily injury.  
note: The mounting holes on the Imitation Dome Camera are approximately 1/4” with 5/32”  
slots. See Figure 4 below.  
opeRation  
Once the two AA batteries are installed in the Dome Camera, the LED light will  
automatically blink in 5 second intervals until the batteries go dead. When the light stops  
blinking, replace the batteries.  
Mounting Holes  
Battery Housing  
FiguRe 1  
note: There are no replacement parts available for this product.  
SKU 95154  
For technical questions, please call 1-800-444-3353  
Page 4  
 

Graco Air Compressor 3A1902C User Manual
Graco Stroller 61236113 amp;6114 User Manual
Greenheck Fan Ventilation Hood SSFSDR 512 User Manual
Grindmaster Beverage Dispenser C 2S User Manual
Haier DVD Player DTA21F98 User Manual
HeadsetUSA Portable Speaker PAS 400 User Manual
Hotpoint Dishwasher lft 3214 User Manual
HP Hewlett Packard Switch 2000fc User Manual
HP Hewlett Packard TV Cables 55330M User Manual
Hunter Fan Air Cleaner 30300 User Manual