UNIVERSAL METAL TOOL STAND
46075
ASSEMBLY INFORMATION
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE ThIS MANUAL.
Copyright© 2001 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 09j
6.
DRESS SAFELY. Non-skid footwear or safety shoes should be used when
working with this product. Do not wear loose clothing or jewelry as they can
become caught in moving parts. Wear a protective hair covering to prevent long
hair from becoming caught in moving parts. If wearing a long-sleeve shirt, roll
sleeves up above elbows.
7.
8.
INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS.
DO NOT OVERREACH. Keep proper footing and balance at all times to prevent
tripping, falling, back injury, etcetera.
9.
STAY ALERT. Watch what you are doing at all times. Use common sense. Do
not use this product when you are tired or distracted from the job at hand.
10.
CHECK FOR DAMAGED PARTS. Before using this product, carefully check that
it will operate properly and perform its intended function. Check for damaged
parts and any other conditions that may affect the operation of this product.
Replace or repair damaged or worn parts immediately.
11.
REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only
identical replacement parts. Only use accessories intended for use with this
product. Approved accessories are available from Harbor Freight Tools.
12.
13.
14.
MAINTAIN THIS PRODUCT WITH CARE. Keep this equipment clean and dry for
better and safer performance.
MAINTENANCE: For your safety, service and maintenance should be performed
regularly by a qualified technician.
USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain
applications for which this product was designed. Do not use small equipment,
tools or attachments to do the work of larger industrial equipment, tools or
attachments. Do not use this product for a purpose for which it was not intended.
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS
1.
2.
DO NOT EXCEED THE 500 POUND WEIGHT BEARING CAPACITY FOR THIS
TOOL STAND.
READ AND UNDERSTAND ALL INSTRUCTIONS AND SAFETY
PRECAUTIONS AS OUTLINED IN THE MANUFACTURERS’ MANUALS OF
THE TOOL(S) TO BE USED WITH THE TOOL STAND PRIOR TO USING THIS
PRODUCT.
SKU 46075
PAGE 3
3.
4.
MAKE SURE THE TOOL STAND IS FIRMLY SECURED ON A FLAT, LEVEL,
STURDY SURFACE CAPABLE OF SUPPORTING THE WEIGHT OF THE TOOL
STAND,TOOL(S) BEING USED, WORKPIECE(S), ETCETERA.
MAKE SURE THE TOOL TO BE USED IS FIRMLY SECURED TO THE TOOL
STAND PRIOR TO USING.
UNPACKING
When unpacking, check to make sure the parts shown on page 8 of this manual are
included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
ASSEMBLY INSTRUCTIONS
NOTE: All parts listed below refer to the parts listed and shown on page 8 of this
manual.
To Assemble The Tool Stand:
1.
2.
The height of the Tool Stand may be adjusted to either 26, 29, or 32 inches.
Position the four Extension Feet (part #6) on the bottom, outside edges of the
four Legs (part #4). (See Assy. Diagram.)
3.
With the aid of a measuring rule, slide the Extension Feet (part #6) up or down
along the bottom, outside edges of the Legs (part #4) until the desired height
of the Tool Stand is reached (26, 29, or 32 inches). NOTE: Make sure the four
mounting holes in each Extension Foot align with four mounting holes in each
Leg.
4.
5.
Insert four Carriage Bolts (part #7) through the four mounting holes in each
Extension Foot (part #6) and Leg (part #4). Attach the Spring Washers (part #9),
and Nuts (part #8) to the Carriage Bolts and loosely tighten.
Align the mounting hole located at each end of a Bottom Long Brace (part #2)
with a mounting hole located on the lower, inside edges of two Legs (part #4).
SKU 46075
PAGE 4
6.
Insert two Carriage Bolts (part #7) through the aligned mounting holes of the
Bottom Long Brace (part #2) and two Legs (part #4). Attach the Spring Washers
(part #9), and Nuts (part #8) to the Carriage Bolts and loosely tighten.
7.
8.
Repeat Steps #5 and #6 above to attach the remaining Bottom Long Brace (part
#2) to the two remaining Legs (part #4).
Position a Bottom Short Brace (part #5) with each of its ends resting above each
end of the two Bottom Long Braces (part #2). NOTE: Make sure to align the
mounting hole located at the top of each end of the Bottom Short Brace with the
mounting hole located at the top of each end of the Bottom Long Brace. Also,
align the the mounting hole located at the side of each end of the Bottom Short
Brace with a mounting hole located on the lower, inside edges of the two Legs
(part #4).
9.
Insert two Carriage Bolts (part #7) through the aligned mounting holes of the
two Legs (part #4) and Bottom Short Brace (part #5). Then, insert two Carriage
Bolts through the aligned mounting holes of the Bottom Short Brace and the two
Bottom Long Braces (part #2). Attach the Spring Washers (part #9), and Nuts
(part #8) to the Carriage Bolts and loosely tighten.
10.
Repeat Steps #8 and #9 above to attach the remaining Bottom Short Brace (part
#5) to the remaining Bottom Long Brace (part #2) and remaining two Legs (part
#4).
11.
12.
Align the mounting hole located at each end of a Top Long Brace (part #1) with a
mounting hole located on the upper, inside edges of two Legs (part #4).
Insert two Carriage Bolts (part #7) through the aligned mounting holes of the Top
Long Brace (part #1) and two Legs (part #4). Attach the Spring Washers (part
#9), and Nuts (part #8) to the Carriage Bolts and loosely tighten.
13.
14.
Repeat Steps #11 and #12 above to attach the remaining Top Long Brace (part
#1) to the two remaining Legs (part #4).
Position a Top Short Brace (part #3) with each of its ends resting above each end
of the two Top Long Braces (part #1). NOTE: Make sure to align the mounting
hole located at the top of each end of the Top Short Brace with the mounting hole
located at the top of each end of the Top Long Brace. Also, align the mounting
hole located at the side of each end of the Top Short Brace with a mounting hole
located on the upper, inside edges of the two Legs (part #4).
15.
Insert two Carriage Bolts (part #7) through the aligned mounting holes of the two
Legs (part #4) and Top Short Brace (part #3). Then, insert two Carriage Bolts
SKU 46075
PAGE 5
through the aligned mounting holes of the Top Short Brace and the two Top Long
Braces (part #1). Attach the Spring Washers (part #9), and Nuts (part #8) to the
Carriage Bolts and loosely tighten.
16.
17.
Repeat Steps #14 and #15 above to attach the remaining Top Short Brace (part
#3) to the remaining Top Long Brace (part #1) and remaining two Legs (part #4).
Place the Tool Stand at the location where it will used. With the aid of a corner
square and/leveler, make sure the top of the Tool Stand is level. Then, WRENCH
TIGHTEN all of the Carriage Bolts (part #7).
To Attach A Plywood Top To The Tool Stand:
1.
2.
3.
4.
Cut a piece of 5/8” or 3/4” plywood (not provided) to the measurements of 18-3/8”
x 20-1/2”. (See Figure A.)
Using a wood drill bit (not provided), drill four 3/8” holes through the plywood.
(See Figure A.)
Using a metal drill bit (not provided), drill two 3/8” holes through each of the two
Top Long Braces (part #1). (See Figure A.)
Place the plywood on the top of the Tool Stand, and insert four 3/8” Bolts (not
provided) downward through the holes in the plywood and through the aligned
holes in the Top Long Braces (part #1).
5.
Attach four Lockwashers (not provided) and four Nuts (not provided) to the four
Bolts, and wrench tighten to secure the plywood to the top of the Tool Stand.
5/8 OR 3/4 THICK PLYWOOD
TOP LONG BRACE (#1)
1-1/2”
1-1/2”
4”
4”
3/8” DIA.
HOLE
18-3/8”
3/8” DIA.
HOLE
18-3/8”
20-1/2”
20-1/2”
FIGURE A
SKU 46075
PAGE 6
Caution:
When using the Tool Stand to support a power tool, the power tool
must be properly secured to theTool Stand using appropriate hardware
(not included). Always read and understand all safety warnings
and instructions provided in the instruction manual provided by the
manufacturer of the power tool being mounted to the Tool Stand.
Before mounting the power tool on the Tool Stand, make sure that
the power tool’s manufacturer endorses the use of the power tool
mounted on a Tool Stand.
INSPECTION, MAINTENANCE, AND CLEANING
1.
Caution: Always disconnect the power tool(s) mounted on the Tool Stand from
their electrical/compressed air power sources before performing any inspection,
maintenance, or cleaning on the Tool Stand.
2.
3.
Before each use, inspect the general condition of the Tool Stand. Check for
cracks and bends in the product, loose or missing Carriage Bolts (part #7), loose
or improper mounting of a tool, and any other condition that may affect the safe
operation of the Tool Stand. If abnormal noise or vibration occurs, turn off the tool
that is mounted on the Tool Stand immediately and have the problem corrected
before further use. Do not use damaged equipment.
Do not use solvents to wipe off the Tool Stand, as damage may result. If
necessary, wipe with a damp cloth. You may use a mild detergent.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THIS MANUAL AS
A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN
FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED
AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 46075
PAGE 7
PARTS LIST / ASSEMBLY DIAGRAM
PART #
DESCRIPTION
Top Long Brace 19.69” (500mm)
Bottom Long Brace 23.74” (603mm)
Top Short Brace 17.71” (450mm)
Leg 26.38” (670mm)
QTY
1
2
3
4
5
6
7
8
9
2
2
2
4
Bottom Short Brace 21.77” (553mm)
Extension Foot 9.76” (248mm)
Carriage Bolt M6
2
4
40
40
40
Nut M6
Spring Washer 06
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 46075
PAGE 8
|