Harbor Freight Tools Tool Storage 47418 User Manual

SERVICE CART  
WITH TOOL CHEST  
47418  
ASSEMBLY INSTRUCTIONS  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
®.  
Copyright © 2004 by Harbor Freight Tools  
All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions and replacement parts, please call 1-800-444-3353  
 
9. Check for damaged parts. Before using any tool, any part that appears  
damaged should be carefully checked to determine that it will operate properly  
and perform its intended function. Check for loose parts and any other condition  
that may affect the operation of this product. Replace loose or worn parts  
immediately. Any part that is damaged should be properly repaired or replaced  
by a qualified technician.  
10. Replacement parts. When servicing, use only identical replacement parts. Use  
of any other parts will void the warranty.  
Warning: The warnings, cautions, and instructions discussed in this instruc-  
tion manual cannot cover all possible conditions and situations that may  
occur. It must be understood by the operator that common sense and caution  
are factors which cannot be built into this product, but must be supplied by the  
operator.  
Unpacking  
When unpacking, check to make sure the following parts are included. If any parts  
are missing or broken, please call Harbor Freight Tools at the number on the cover of  
this manual.  
Assembly Instructions  
1. Assemble all parts on a smooth surface to avoid scratching.  
2. Select the shorter Side Brace (3) for the left side and the longer Side Brace (3)  
for the right side. Attach the lower Tray (2) to the Side Braces (3) by matching  
up the holes and securing with Bolts (1), through Side Brace (3). Secure with  
Washers (11), Spring Washers (12), and Nuts (13). Finger tighten.  
See Figure A.  
3. In the center of the Side Brace (3), attach Support Brace (7) by threading Bolt  
(1) through Side Brace (3). Secure in place with Washer (11), Spring Washer  
(12), and Nut (13). Repeat for other side. See Assembly Drawing. Tighten all  
hardware.  
Shorter Side  
Brace (3)  
Bolt (1)  
Washer (11)  
Spring Washer (12)  
Nut (13)  
Tray (2)  
Longer Side  
Brace (3)  
Figure A  
SKU 47418  
Page 3  
 
4. Position the Tool Chest (8) between the two Side Braces (3), resting the Tool  
Chest on the Support Braces (7). From the underside of the Tool Chest (8)  
match up the holes on the Tool Chest and those in the Support Braces (7).  
Put Washer (14) on Bolt (15) and thread bolt into the bottom of the Tool Chest  
and Support Braces. See Figures A & B.  
Washer (14)  
Bolt (15)  
Support  
Brace (7)  
Tool  
Chest (8)  
Tool  
Chest (8)  
Side Brace  
(3)  
(View from Underneath)  
Figure C  
Figure B  
5. Attach the Upper Tray (2) by matching up the holes and securing with Bolts (1)  
threaded through the Side Braces (3). Secure with Washers (11), Spring  
Washers (12), and Nuts (13) on the inside of the Tray. Tighten hardware.  
See Figures C & D .  
Upper  
Tray (2)  
Bolt (1)  
Washer (11)  
Spring Washer (12)  
Nut (13)  
Caster  
with Lock (4)  
Sheath (6)  
Figure E  
Figure D  
6. Place Caster with Locks (4) and Sheath (6) into the longer side Brace (3). The  
longer Side Brace acts as a handle for the Service Cart with Tool Chest. Place  
Casters without Locks (5) and Sheath (6) into the shorter Side Brace (3).  
See Figure F. (When not repositioning Service Cart, use the locks on the  
Casters (4). Unlock to move Cart). Caution: Casters without Locks (5) can  
still move to the right or left. See Figure D.  
Caster (5)  
Sheath (6)  
Caster with  
Lock (4)  
Sheath (6)  
Figure F  
7. Objects need to be distributed evenly in the Tool Chest drawers to avoid  
tipping. Do not overload Trays (2) when moving Service Cart.  
SKU 47418  
Page 4  
 
Parts List  
Part #  
Description  
Qty.  
Part #  
Description  
Qty.  
Handle  
Bolt M8 x 15  
Washer 6  
Spring Washer 6  
Nut M6  
Washer 5  
Bolt M6 x 32  
2
4
12  
12  
12  
4
12  
2
2
2
2
4
2
1
1
2
3
4
5
6
7
8
9
Tray (One Shorter than Other)  
Chrome Side Brace  
Caster With Locks  
Caster Without Locks  
Sheath  
10  
11  
12  
13  
14  
15  
Bolt M5 x 8  
Support Brace  
Tool Chest  
4
Assembly Drawing  
Part 11  
Part 13  
Part 12  
Part 2  
Part 3  
Part 3  
Part 1  
Part 8  
Part 8  
Drawer  
Drawer  
Part10  
Part 7  
Part 7  
Part 14  
Part 15  
Part 6  
Part 6  
Part 2  
Part 6  
Part 5  
Part 5  
Part 4  
Part 4  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS  
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR  
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS  
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO  
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR  
EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN  
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES  
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR  
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-  
MENT PARTS THERETO.  
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.  
SKU 47418  
Page 5  
 

Haier Air Conditioner HSU18VH7 User Manual
Hamilton Beach Waffle Iron 26020 User Manual
HANNspree Computer Monitor SN22A1 User Manual
HANNspree Flat Panel Television DT06 10C1 User Manual
Harbor Freight Tools Electric Steamer 94924 User Manual
Harbor Freight Tools Grinder 52847 User Manual
Heatcraft Refrigeration Products Humidifier H IM CU User Manual
Husqvarna Lawn Mower 15T User Manual
iLive Speaker System iHMD8816DT E1 User Manual
Impex Home Gym MD 859 User Manual