Harbor Freight Tools Work Light 47078 User Manual

QUICK ACTION  
8-POSITION WORKBENCH  
47078  
ASSEMBLY & OPERATING INSTRUCTIONS  
®
3
 
8. Use eye and ear protection. Always wear ANSI approved impact safety goggles.  
9. Do not exceed products maximum load capacity. Make certain that the Workbench can  
support all tools and accessories, as well as any workpiece.  
10. Avoid Sharp edges when assembling.  
11. Always check hardware and assembled parts after assembling. Place in an area that is  
flat and level. All connections should be tight and hardware tightened.  
12. Do not allow children to play on, stand upon or climb upon the Workbench.  
Warning:  
The warnings, cautions, and instructions discussed in this instruction manual cannot  
cover all possible conditions and situations that may occur. It must be understood by  
the operator that common sense and caution are factors which cannot be built into  
this product, but must be supplied by the operator.  
Assembly  
Your Quick Action 8-Position Workbench will require complete assembly prior to use. It is important  
that you read the entire manual to become familiar with the product BEFORE use. Before  
assembling the Workbench be sure that you have all parts described in the Parts List and Assemby  
Diagram located on the last pages of this manual.  
Step 1)  
Step 2)  
Step 3)  
Step 4)  
Locate the two (2) Left Leg Stand Frames (#26). Attach Tool Holder (front) (#24) to  
the Left Leg Stand Frames (#26) by inserting a Hex Bolt (#29) through each corner  
of the Tool Holder (front) and through the Left Leg Stand Frame(s). Slide on Flat  
Washer (#19) and fasten Hex Nut M6 (#18).  
Locate the two (2) Right Leg Stand Frames (#27) and attach Tool Holder (back) (#25)  
by inserting a Hex Bolt (#29) through each corner of the Tool Holder (back) (#25) and  
through the Right Leg Stand Frame (#27). Slide on Flat Washers (#19) and fasten in  
place with Hex Nut M6 (#18).  
Attach the Left Leg Stand Frames (#26) to Right Leg Stand Frames (#27). Insert  
Hex Bolt (#20) through Right Leg Stand Frames (#27) and slide on Spacer (#17)  
then slide on Left Leg Stand Frame and Washer (#19). Secure with Hex Nut (#18).  
Repeat for second side of Workbench-see Figure 1.  
Attach the Grip (#28) to the lowest hole in the top extension of the Left Leg Stand  
Frames (#26) with Hex Bolt (#29) Washer (#19) and Hex Nut (#18)-see Figure 2.  
Figure 1  
Right Leg Stand Frame (#27)  
Spacer (#17)  
Hex Nut (#18)  
Hex Bolt (#20)  
Left Leg Stand Frame  
(#26)  
Washer (#19)  
#47078  
Page 3  
 
Figure 2  
Washer (#15) with Hex Nut (#14)  
U-Frame Channel (#10)  
Cross Head Bolt (#16)  
Washer (#19)  
Hex Nut (#18)  
Grip (#28)  
Hex Bolt (#29)  
Washer (#19)  
Hex Nut (#18)  
Step 5)  
Step 6)  
Through the center hole in the extension, insert Hex Bolt (#29), slide on Washer  
(#19) and fasten with Nut (#18)-see Figure 2.  
Set the U-Frame Channel (#10) on top of the Right Leg Stand Frame (#27) as shown  
in Figure 2. Attach the U-Frame Channel (#10) to the Right Leg Stand Frame (#27)  
with Cross Head Bolt (#16); slide on Washer (#15) and tighten on Hex Nut (#14)-see  
Figure 2.  
Step 7)  
Attach the Left Leg Frame Stand (#26) extension to the U-Frame Channel (#10).  
First, hold the Spacer 22 mm (#9) between the Left Leg Frame Stand (#26) and the  
U-Frame Channel (#10), then insert the Cross Head Bolt (#8) through Left Leg  
Frame Stand (#26) through Spacer (#9) and through U-Frame Channel (#10). Slide  
on Washer (#15) and Nut (#14)-refer to Figure 3.  
Figure 3  
Spacer (#9)  
U-Frame Channel (#10)  
Cross Head Bolt (#8)  
Washer (#15) and Nut (#14)  
Left Leg Frame Stand (#26)  
Step 8)  
On the underside of the U-Frame Channel (#10), insert the Sliding Locking  
Block (#13) with Spring (#12) (see Figure 4) and Check Pawl (#11). On the top of  
the U-Frame Channel, set the Connecting Part (#7).  
Figure 4  
Spring (#12)  
Sliding Locking  
Block (#13)  
#47078  
Page 4  
 
Step 9)  
Lay the Table Top Back (#6) on top of the Connecting Parts (#7). Through the inside  
hole, insert Cross Head Bolt (#3) with Washer (#4) so that it threads down through  
the Connecting Part (#7) and into the Check Pawl (#11) and Sliding Locking  
Block (#13).  
Step 10)  
Step 11)  
Step 12)  
Through the outside holes in the Table Top Back (#6), thread the Push Button (#2)  
into the Connecting Part (#7) and into the Check Pawl (#11) and Sliding Locking  
Block (#12).  
Lay the TableTop (front) (#23) onto the Threaded Sliding Blocks (#21) which are set  
in place on the U-Frame Channel (#10). Screw in Cross Head Bolt (#22) with  
Washer (#4) through the Table Top (front) and into the Threaded Sliding Blocks (#21).  
As necessary, attach Rubber Feet (#30) to each Leg Stand Frame.  
Operation  
The Quick Action 8-Position Workbench folds for easy travel and storage.  
Step 1)  
The Table Top (front) (#23) can be moved by turning the Handles on the U-Frame  
Channel (#10). Turning the Handle clockwise will move the Table Top in towards the  
other Table Top. Turning the Handle counterclockwise will move the Table  
Top (front) (#23) out.  
Step 2)  
Pressing on the red Push Buttons (#2) with your thumb allows you to grasp the Table  
Top (back) (#6) with your hands and fingers and slide it forward or backward while  
the Push Buttons (#2) are pressed down. Releasing the Push Buttons (#2) will lock  
the Table into place-see Figure 5.  
Figure 5  
Step 3)  
The Swivel Pegs (#1) and Peg Supports (#5) can be placed into any hole in the Work  
Table top provide a block to secure and block your workpiece.  
PLEASE READTHE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL AS A REFERENCE  
TOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY  
KINDTOTHE BUYERTHAT HE OR SHE IS QUALIFIEDTO MAKE ANY REPAIRSTOTHE PRODUCT ORTHAT HE OR SHE IS  
QUALIFIEDTO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY  
STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED  
TECHNICIANS AND NOT BYTHE BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER  
REPAIRSTOTHE ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER  
INSTALLATION OF REPLACEMENT PARTSTHERETO.  
#47078  
Page 5  
 
Unpacking  
When unpacking your Quick Action 8-Position Workbench, check to make sure the following parts  
are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at  
1-800-444-3353.  
Parts List- Quick Action 8-Position W\orbench  
Part # Description  
Quantity Part # Description  
Quantity  
1
2
3
4
5
6
7
7A  
8
Swivel Peg  
Push Button  
4
2
2
4
2
1
2
2
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
Cross Head Bolt m 8 x 45  
Spacer 9.5 mm  
Hex Nut  
2
2
10  
10  
2
2
2
1
1
1
1
1
1
8
4
Cross head Bolt M8 x 65  
Washer 8 x 21 mm  
Peg Support  
Table Top (back)  
Connecting Part  
Connecting Part  
Flat Washer 6 x 12 mm  
Hex Bolt M6 x 58  
Threaded Sliding Block  
Cross Head Bolt M8 x 50  
Table Top (front)  
Tool Holder (front)  
Tool Holder (back)  
Left Leg Stand Frame  
Right Leg Stand Frame  
Grip  
Cross Head Bolt M8 x 55 2  
9
Spacer 22 mm  
U-Frame Channel  
Check Pawl  
Spring  
Sliding Locking Block  
Hex Nut M 8  
2
2
2
2
2
4
4
10  
11  
12  
13  
14  
15  
Hex Bolt M 6 x 35  
Rubber Feet  
Flat Washer 8 x 16 mm  
Note: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
#47078  
Page 6  
REV 01/05  
 
Parts/Assembly Diagram  
21  
7A  
21  
7A  
#47078  
Page 7  
REV 01/05  
 

Graco Baby Accessories PD161932A User Manual
Grizzly Lawn Sweeper T10042 User Manual
Grundig CRT Television AMIRA26HDBLK User Manual
Hamilton Beach Air Cleaner 840117900 User Manual
Hoshizaki Ice Maker FS 1001MLH C User Manual
Humax DVR IRCI PVR User Manual
iHome Car Speaker DFM13 User Manual
Iiyama Computer Monitor E1908WSV User Manual
Image Treadmill IMTL119050 User Manual
i Tech Dynamic Headphones Clip III User Manual