Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: [email protected]
REV 14h
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
12. Do not operate the Worklight in
explosive atmospheres, such as in the
presence of flammable liquids, gases,
or dust. Electrical products create sparks
which may ignite the dust or fumes.
15. Warning: The warnings, cautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
13. Do not submerge in water
or any other liquid.
14. WARNING: The cord of this product
contains lead and/or di (2-ethylhexyl)
phthalate (DEHP), chemicals known
to the State of California to cause
cancer, and birth defects or other
reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
Assembly
1. Charge the Worklight before
using it for the first time.
5. To turn the Worklight on, press down
on the On/Off Switch. To turn the
Flashlight “OFF”, press down on the
opposite end of the On/Off Switch.
2. Plug the AC/DC Adapter into the
Worklight at its base. Plug the AC/DC
Adapter to a 120V electrical outlet.
On/Off
Switch
Adapter
Connection
6. The Cigarette Adapter contains one
250V, fast acting 3 Amp Fuse. To replace
the Fuse, make certain the Adapter
is unplugged. Open up the Cigarette
Adapter, remove Fuse and insert
3. Allow the Worklight to charge. Charging
Indicator Light is the bottom LED bulb
in center row. When Unit is charging,
Charging Indicator Light will glow
red. When Charging Indicator Light
glows green, unit is fully charged.
Disconnect the AC/DC Adapter.
new one. Close Cigarette Adapter.
7. The Worklight can be attached to metal
work surfaces by placing its magnetic
base against the metal portion of the
work surface. The Worklight can also be
hung by the Hanging Hook at its top. The
Hanging Hook swivels 360 degrees.
4. The Worklight also has a cigarette lighter
adapter which can be plugged into a
vehicle’s cigarette lighter. Allow Batteries
to charge. Disconnect the Adapter.
Item 94668
For technical questions, please call 1-888-866-5797.
Page 3
Parts List
Part
Description
Qty.
Record Serial Number Here:
1
2
3
4
5
AC/DC Adapter
Cigarette Adapter
1
1
1
1
2
Note: If product has no serial number,
record month and year of purchase instead.
Led Light
Fuse 250 V, Fast Acting 3 Amp
“S” Hanging Hook
Note: Some parts are listed for illustration
purposes only, and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS DOCUMENT
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
|