Hauppauge Car Satellite TV System WinTV NOVA S USB2 User Manual

In the installation window click on  
Step 1: Install WinTV Drivers.  
Safety information  
2. Installing the WinTV-NOVA-S-USB2  
1.Locate a free USB 2.0 port (normally located at the side or back on  
the computer). Due to power and bandwidth requirements, we do  
not recommend connecting the unit into a USB Hub.  
2.Turn on your PC or Laptop and wait until Windows has completely  
started.  
A blue screen will open which will  
begin installing and updating the  
drivers for your product.  
Important Notice for placing the Device  
Every electrical device needs time to warm up. The heat generated by  
the device is low but can still cause sensitive furniture to alter over  
time. The bottom of the NOVA-S-USB2 can in some cases stain the  
surface of certain furniture. Please put a pad underneath when pla-  
cing the NOVA-S-USB2 on a sensitive surface.  
WinTV-NOVA-S-USB2  
Quick Installation Guide  
3a. Plug the AC adapter to a 220V power outlet.  
©Hauppauge Computer Works, Inc. 2007 · QI-NOVA-S-USB2-V1.0-ENG · 2007/11/08  
Ventilation  
3b.Plug the AC adapter cord to the DC IN 7.5V jack of  
WinTV-NOVA-S-USB2.  
4a. Plug the USB cable into the mini-USB connector of  
WinTV-NOVA-S-USB2.  
Once complete, a message  
appears in the bar. If this message  
is Drivers have been updated  
Successfully, click on the bar to  
exit. If the message reports an  
error, check the connection of  
your WinTV, or contact our tech-  
nical support.  
Next, click on Step 2: Install  
WinTV and select your language  
from the list. The setup window  
should appear and begin to auto-  
matically install the WinTV appli-  
cations.  
Never obstruct the NOVA-S-SUB2 air vents. Always make sure that  
air can ventilate from the device. Never place the device inside a clo-  
set or cabinet. Do not place anything on top of the device and leave  
at least 30 cm of space above it.  
Hauppauge Computer Works, Ltd.  
Tech Support: (+44) 0207 378 0202  
Telephone: (+44) 0207 378 1997  
Fax: (+44) 0207 357 9171  
10 Borough High Street  
Bank Chambers  
4b.Plug the USB cable into the USB 2.0 port of your PC.  
Moisture, direct sun light and heat  
Keep the NOVA-S-USB2 away from moisture and condensing water.  
Never place the device near to a heater or in direct sunlight.  
London, UK, SE1 9QQ  
ote: If you plug the device into a different USB socket, you  
Nmay need to reinstall the WinTV-NOVA-S-USB2 driver, but you  
will not need to reload any WinTV applications.  
Power supply  
Only operate the NOVA-S-USB2 using the supplied AC adapter 7,5 V /  
1,5 A. We recommend disconnecting the power supply from the  
NOVA-S-USB2 when not in use.  
3. Install the WinTV Drivers and Applications  
System requirements  
ote: If you have any anti-virus software enabled, please dis-  
Nable it during the installation of the software.  
Before installing please ensure that your computer meets the follow-  
ing requirements:  
Windows XP with Service Pack 2 or Windows Vista  
One free USB 2.0 port  
Before installing and using the NOVA-S-USB2 please read this guide  
including the Safety Information.  
1. Connecting the Satellite LNB cable  
When you attach the WinTV-  
NOVA-S-USB2, the Found New  
Hardware Wizard will appear.  
ote: During the installati-  
Non, other installation  
wizards may open, we recom-  
mend following the instructions  
in each of these and installing  
with the default options availa-  
ble.  
Please ensure that you have a suitable universal LNB, satellite dish and  
cable before connecting and configuring the WinTV-NOVA-S-USB2.  
Your satellite dish should be installed correctly and should be pointing in  
the right direction. (Please consult your local Satellite installer for further  
details or help).  
Most satellite installations in the UK are selected to either Astra 28.2 DE  
(SKY Digital), Astra 19.2 DE or Hotbird / Eutelsat 13. These are the most  
common satellites that have Free to air television digital channels.  
You can now connect the Sat IN Satellite-Antenna (F-type LNB connec-  
tion) to the WinTV-NOVA-S-USB2.  
Click on Cancel.  
Contents of this WinTV package  
ote: For advanced users  
Nyou can select the 'Custom  
Installation' which will allow  
you to modify the list of appli-  
cations that are installed by  
default.  
WinTV-NOVA-S-USB2  
AC adapter 7,5V DC / 1,5A  
USB Cable  
IR remote control transmitter  
and 2 batteries  
Insert your WinTV Installation  
CD-ROM, the installation window  
will automatically appear.  
DC connection in for the supplied  
LNB-OUT - Output for SAT signal (only  
power supply (7.5 V/1,5 A)  
with available with some models)  
WinTV Installation CD-ROM  
including the following soft-  
ware components:  
· New WinTV v6 application  
· WinTV-Scheduler  
· VTPlus  
ote: If the autorun does  
Nnot start, browse to the  
files on the disc and double  
click on the file called 'Setup'.  
LNB-IN - SAT-antenna input from the  
USB - Mini USB input connection  
for the supplied USB cable  
LNB of your satellite dish  
This installation guide  
Once the WinTV installation is complete, click OK then Exit in the win-  
dow "Hauppauge WinTV Installation CD". You should now be back at  
your Windows desktop.  
Page 1  
Page 2  
Page 3  
Page 4  
®
Pref button  
4. New WinTV v6 Application  
Watch TV  
Pause, Record and Playback TV  
Click the Pref button to open the preferences menu:  
View: These are the settings for the On Screen Display of the TV  
channel and Audio Volume, where you can enable Close Captions (if  
supported in your system configuration), plus controls for the Toolbar  
mode (Title mode), NoToolbar mode (No Title) and Full Screen (TV  
mode).  
To start the WinTV application, double click on the WinTV icon.  
There are four buttons to control the watching, recording, pausing and  
playback of TV. Clicking on the Pause button will cause the Pause  
menu to roll down from the WinTV application, while clicking on  
either the Record or Playback button will cause the Record menu to  
roll down. Click the TV button will close the roll down menus to close  
and for live TV to be displayed in the WinTV video window.  
TV Mode  
Minimise  
When you run WinTV for the first  
time, a message will appear asking  
you to scan for Satellite channels  
now. Please ensure that the LNB  
cable is connected is connected,  
click YES.  
Channel up  
Channel down  
Channel surf  
Last channel  
Freeze picture  
Volume  
Always on Top  
Setup Menu  
Mute  
Remove toolbars  
no title mode  
Close  
Movies: Here is where you configure some video and audio settings.  
You can set the movie record directory (DVCR Record File Path).  
Snapshot: Set the size of your captured images, plus single or two  
field captures for capturing motion or still image video.  
Click your right mouse button  
in the TV window to remove  
toolbars. Click again to  
restore toolbars.  
CFG  
Playback  
Configure Snapshot  
Snapshot viewer  
window:  
Live TV Pause Record  
Audio: Your audio settings are configured here.  
Current TV channel  
Click your right mouse  
button here to see the  
channel selector  
Double click on each  
thumbnail to see  
image full size.Click  
and hold your right  
mouse button to see  
image options.  
Menu button  
Pause mode  
Snapshot Still  
capture  
Click the Menu button to open the TV setup menu. Here is the main  
control bar for TV channels, and duplicate controls for other functions:  
The pause mode allow you to pause the Live TV picture and allows  
you to use the TimeShift function to rewind and fast forward the TV.  
Clicking the Pause button on the WinTV application starts the Pause  
mode. The Pause Menu will drop down.  
Suite-Manager: Configure the TV tuner (scanning, channel pre set,  
etc.) and setting up favourite channel lists.  
Configuration: Duplicate configuration menus for colour, audio, etc.  
View: For settings an exact TV window size: 320x240, 640x480 etc.  
TV-Mode Pause Record Playback  
TV-Mode Pause Record  
Changing channels  
You can change channels by using the Channel Up or Channel Down  
buttons on the WinTV. You can type a channel number (for example:  
27) and WinTV will tune to that channel. If the entered channel does  
not exist, you will see a black window.  
Time counter  
Skip forward 10 sec  
Fast forward  
You can also right click in the Current TV channel box, where you will  
see a list of channels. Or type letters (for example: BBC) to access to  
the list of the channels including these letters.  
In the scan tab click on the Config button and then select your Area  
that you want to use for finding your local satellite (e.g. UK should  
select Europe).  
Select from the drop Satellite-A box the actual satellite that you have  
your dish pointed to (e.g. UK users that have their satellite dish point-  
ed at BSKYB Sky Digital direction should select the 0282-ASTRA  
2A,2B,2D).  
If you have more then 1 LNB you will need to set the DiSEqC” level,  
please refer to the manual for more information.  
In Europe the main satellite’s that are used are: Astra 19.2, Astra 28.2  
or Hotbird 13. In most satellite installation only LNB_1 / Satellite-A will  
be used.  
Video-position  
Fast rewind Pause  
Play Fast forward  
Slow motion  
Pause Buffer  
TV Mode  
The Pause buffer is space on your hard disk where video is stored  
during the Pause mode. The maximum amount of time which your TV  
program can be delayed is dependent upon how much storage space  
you have set for the Pause buffer.  
When you click the Full screen TV button, TV will appear full  
screen on your PC monitor. When finished watching TV full screen,  
click your right mouse button in the TV window. If you see video with  
a black box around it, click the Pref button then click TV mode tab.  
Check the box which says Allow resolution change”.  
Clicking the Pause button will start recording into WinTV's Replay  
Buffer. It takes about 10 seconds for the Replay Buffer to be initialized  
and for Pause to become effective.  
Unclicking the Pause button will cause the audio/video program to  
start playing from the point where the button was originally pushed.  
Most WinTV functions are active while in the Pause or Pause Live  
mode. For example, you can change volume, resize the TV window,  
go into "no-title mode", etc.  
While in Pause mode, the Video Position bar shows the amount of the  
Replay Buffer which is filled with video. For example, if the Video  
Position indicator shows halfway, it means that half of the Replay  
Buffer is filled. If you find you cannot Pause as many minutes as you  
would like, increase the size of the Replay Buffer.  
"Always on top" Mode  
The WinTV application will remain in view over any other applica-  
tions even if it is not selected. To turn on, click the Always on top  
button. It will turn green. To turn off, click this button again.  
A convenient way to use Always-on-top is to make the TV window in  
the no-title mode small, and to make the TV window in the title mode  
larger. Then you can switch from a small window to a larger one by  
clicking the right mouse button.  
ote: For more information LNB and DiSEqC settings please  
Nrefer to the manual.  
Click on the “Scan“ to start the scanning process which may take  
some time.  
When channels are found they will appear in the space on the bottom  
right hand side window. Once you have completed configuring your  
sources click on “Close”.  
Page 5  
Page 6  
Page 7  
Page 8  
While in Pause mode, the A/V stream is always saved in the Replay  
Buffer. To stop saving the A/V stream in the Replay Buffer, you must  
exit the Pause mode by clicking TV mode.  
Slow Motion  
Record and Playback modes  
5. WinTV-Scheduler  
Clicking the Slow Motion button during playback will cause the  
video to play in slow motion (at 1/2 speed). Clicking the Slow Motion  
button again will return the video to normal playback speed.  
Record  
WinTV-Scheduler allows you to schedule the recording of TV shows.  
WinTV-Scheduler, once it is set, can be closed, and the WinTV applica-  
tion will “wake up” at the desired time and tuned to the desired channel.  
After installation, WinTV-Scheduler can be found by going to  
Start / Program files / Hauppauge WinTV.  
Replay  
While in the Pause mode, hitting the Replay button acts like the  
Instant Replay you see on TV broadcast sporting events: the  
audio/video goes back in time and you repeat what you have previ-  
ously seen. Each click of the Replay button causes audio/video to go  
back 10 seconds. For example, if you want to repeat the audio/video  
you saw 10 seconds ago, you would click the Replay button once. If  
you want to see the video you saw one minute ago, you would need  
to click the Replay button six times.  
File button  
Display Counter  
Clicking the File button opens the File menu. The last file record-  
ed is listed in the File name box. In the File menu you can:  
File  
To set up an event for timed watching or recording, click on the Add  
Program.  
Stop  
Rewind Pause  
Play Forward  
Rename your recorded video file: To rename a video file, find the  
file you would like to rename, highlight it with your mouse, and click  
and hold the right mouse button. Go down to Rename and then you  
can type in a new name. Remember: you must keep the MPG  
extension on the file.  
Play a video file previously recorded: Find the file you would like to  
play, highlight it with your mouse (one click of the mouse button)  
and click Open. Then click the Play button.  
Video-Position  
Play forward slow  
Click the Playback button on the WinTV application to open the  
Record and Playback control bar. Clicking the Record will automatical-  
ly generate a file name and start recording your audio/video program.  
If you click Record button more than once, a record timer will be set  
and the recording will be done for 15 minutes for each time the  
Record button is clicked. For example, if you click the button 3 times,  
the WinTV will record for 30 minutes.  
For extended replay times, you might find it more convenient to grab  
the Video Position indicator control bar and move it to the left. Once  
you let the control bar go, audio/video starts to play (it might take a  
few seconds for the WinTV application to start playing).  
You might have to move the Video Position indicator to the left and  
right to find the desired spot to start replaying audio/video.  
While Replaying, your audio/video program continues to be recorded  
in the Replay Buffer. Therefore, if you have clicked the Replay button 3  
times (so that you are replaying the audio/video seen 30 seconds  
ago), the video you see in the WinTV window will be 30 seconds  
behind the live program.  
Delete recorded video files which you no longer want: Click your  
right mouse button on the video file once, go down the menu and  
click Delete.  
Functions:  
When recording TV, the record button will depressed  
WinTV-Scheduler works by using the Windows Task Scheduler to  
launch WinTV at the chosen time. WinTV-Scheduler sets up a com-  
mand line in Task Scheduler to run WinTV, specifying a TV channel  
and a length of time to record.  
A time counter will be shown indicating the lenght of time of the  
recording  
If you click Stop the time counter will revert back to 00:00:00  
The time is specified in a Hour:Minute:Second format.  
Keyboard shortcuts  
Sound up - Page Up  
Sound down- Page Down  
Ctrl+M  
ALT+M  
0-9  
- Mute on/off  
- Re-size TV menu  
- Channel number  
Plus (+)  
Minus (-)  
Ctrl T  
- Chanel Up  
- Channel Down  
- Frame TV  
Skip Ahead  
Stop  
Space bar - Take a snapshot  
Ctrl F - Still image  
Clicking the Skip button will skip the video ahead 10 seconds.  
Clicking the Stop button will stop the video you are recording or  
playing back.  
Rewind  
Ctrl P  
- Frame print  
Clicking the Rewind button while playing video will rewind the  
recorded video. Clicking the Rewind button again will continue the  
playing.  
Play  
Clicking the Play button will playback from disk the last video file  
created. When playing a video, you can rewind, fast forward, replay  
10 sec or skip forward 10 sec using the buttons on the control bar.  
Slow Motion  
Clicking the Slow Motion button while playing video will play in  
Slow Motion. Clicking the Slow Motion button again, will continue  
playing normally.  
Pause  
Clicking the Pause button while Playing will pause your  
audio/video.  
Fast Forward  
Rewind  
Clicking the Fast Forward button once will fast forward your video  
at 2X speed. Clicking the Fast Forward button twice will fast forward  
your video at 8X speed.  
Clicking the Rewind button will play the video file in reverse.  
Clicking the Rewind button again will continue the playing of the video.  
Fast Forward  
Clicking the Fast Foward button once will fast foward your video  
at 2X speed. Clicking the Fast Foward button twice will fast forward  
your video at 8X speed. Clicking the button again will continue play-  
ing back at normal speed.  
The items that need to be set for each event are:  
Source selection: leave set at WinTV to bring up the WinTV at the  
requested time and on the requested channel. Select Reminder to  
just pop-up a text file as reminder.  
 
Page 9  
Page 10  
Page 11  
Page 12  

Graham Field Mobility Aid 716070A User Manual
Gravely Lawn Mower 988100 User Manual
Haier Clothes Dryer CHDE5000AW User Manual
Harbor Freight Tools Saw 93012 User Manual
Hasbro Games Treehouse Playset User Manual
HP Hewlett Packard Computer Hardware AP836B User Manual
HP Hewlett Packard Copier C8431 90109 User Manual
Hubbell Work Light UE24 User Manual
Huffy Fitness Equipment 104 03P N211956B User Manual
Hypertec Carrying Case N14618PHY User Manual