Motion Sensing Light Fixture with Accent Lighting
Models 3038361/3038379
2. Aiming
Note: Installation of this light control should be done only by
those with experience in 120 Volt household wiring. Some lo-
cal codes may require that a licensed electrician install the light
control.
The coverage area for the sensor is shown in Figure 2. The sensor
should be aimed so that the motion to be detected is in front of and
across the coverage area. The sensor should be aimed looking out
at a horizontal angle. To reduce false triggering, point the sensor
away from traffic areas, air conditioners, dryer vents, water pools,
or anything which may move or change temperature rapidly.
This light control automatically turns on lights when motion is
detected.
Two lamp holders are provided. The lamp holders are rated at 150
watts max. each.
240°
1. Installation
Caution: Always turn the circuit breaker off when wiring the
fixture.
8 Ft.
1. Remove the existing fixture.
2. The plastic hanger can be used to hold the fixture while wiring.
The small end of the plastic hanger can be threaded through the
hole in the center of the cover plate. The small end then goes into
one of the slots on the mounting strap.
3. Connect the light control as shown in Figure 1:
• Black sensor wire to the black (HOT) house wire.
• White sensor wire to the white (NEUTRAL) house wire.
100 Ft.
Figure 2 Coverage Angles
3. Testing
Turn the power back on at the circuit breaker. Turn the light switch
on.
Note: When first turned on wait about 1 1/2 minutes for the circuitry
White to white
Black to black
to calibrate.
From
Put the TIME switch on the bottom of the sensor in the TEST posi-
tion.Youcannowwalkinfrontoftheunitandthelightswillcomeon
for about 5 seconds. The TEST mode works both day and night.
House
Push the rubber
plug firmly into
place
Walk through the coverage area and point the sensor to obtain the
desired coverage area. Adjust sensitivity as needed. Use Range
Boost only if required.
House ground wire to green
ground screw on fixture.
4. Operation
For motion sensing, put the ON-TIME switch on the bottom of the
sensor in the 1, 5 or 20 minute position. When motion is detected,
the lights will come on the selected time. Note: The photocell keeps
the lights from turning on in daylight.
Figure 1 Wiring at Junction Box Plate
4. Attach the fixture to the mounting strap with the center mount-
ing bolt. Use a weatherproof sealant to seal the fixture to the
junction box.
5. Install the protective lamp shields on the lamp holders by lining
up the groves on the narrow end of the shields with the dimples
in the lamp holders, push the shields into the lamp holders and
turn clockwise slightly.
6. Install the lamps in the lamp holders. Do not over tighten.
7. Adjustment lamp holders. The lamps should be at least 1 inch
away from the sensor.
To keep lights on all night, flip the light switch off for 1 second
then back on. Turning the light switch off for 1 second then back
on will return the control to the motion sensing mode. At dawn, the
control will return to the motion sensing mode and shut off.
®
ForAccent Lighting, set the DualBrite switch to the 3, 6, or Dusk
to Dawn setting. The lights will then turn on dim at sundown for the
set time. When motion is sensed the lights will turn on full bright.
Specifications:
CAUTION: Do not mount the sensor above or touching the lamps
(keep 1 inch or more from the lamps). The sensor bottom must
be facing down for best coverage and to avoid water damage
and electrical shock.
Total Lighting Wattage.....................................................300 watts
Lamp Holder Wattage .....................................150 watts max. each
Range ......................... up to 70 ft.; up to 100 ft. with Range Boost
Time Delay......................................................... 1, 5 or 20 minutes
Accent Lighting Timer...........................3, 6 hours, Dusk-to-Dawn
Note: For under-eave installation, rotate the sensor head 180° by
bending the sensor towards the clamp bracket. Rotate the sensor
bottom clockwise away from the bracket.
Caution: This product is to be used with a U.L. listed rain tight
or wet location suitable outlet box. Depending on the installation,
additional hardware may be required.
595-5754-03
© 2008
|