50336/50337.instructions 3/26/01 11:29 AM Page 1
• Remove remaining 3-way switch from the junction box.
INSTALLING THE SWITCH
3-Way With One Motion Sensing Switch
• Add the jumper wire to the common lug and to either one of the two switched lugs. If you're not sure which
lug is common, install the jumper on any two of the three wires, and test the jumper as explained on the next
page.
Test for correct common wire connection:
Re-install the switch.
WARNING: Turn power off at the circuit breaker before wiring.
3-Way Motion
Turn the circuit
breaker back on.
Note: a "3-way" circuit controls lights from two sepa-
Sensing Switch
rate switches. If you want to use this product in a sin-
gle switch circuit or if you want to install more than one
motion sensing wall switch, see page 6
• Remove the decorative coverplate (secured by two
screws).
The 3-Way Motion Sensing Switch (MSS) detects motion to turn on
lights for an adjustable amount of time. A built-in photo cell can be set
to keep lights off when the lights aren't needed. The unit has excellent
sensitivity and a wide 1500 detection range. It can be used with incan-
descent lighting as well as rapid start fluorescent lighting.
Common
Switch Lug
The switch may
indicate the
Leaving the jumpered switch in one position,
flip the other 3-way switch on and off.
• Remove Control Cover. (Press in with screwdriver.
Swing out cover to remove.)
COMMON
common
Hot Wire
• Choose which switch will be replaced and remove it.
• For easier re-wiring later, mark the house wiring with
tape indicating where the wire had been connected.
The MSS can be used to replace either a 3-way wall switch or a
single pole switch. Some codes require installation by a qualified elec-
trician.
OR
OFF AUTO
ON
Features include:
Color of screw
may be different
for the common
Lights
turn on
and off.
Jumper is
correct. Go
to next page.
• 1500 motion detection angle
Jumper
Yes
• Adjustable on-time from 5 sec. to 20 min.
• Adjustable photocell
• Works with incandescent and rapid start fluorescent lighting
• Works with motors up to 1/8 hp.
• Slide switch selectable OFF, ON AND AUTO modes.
No
Common Switch Lug
Hot Wire
Included are: • The sensor switch • Cover plate • 4 wire connectors • 2 large screws • 2 small screws.
To Brown wire
of MSS
(note Color)
Hot Wire
Move one end of the jumper
wire to the previously
Flip the switch with the
jumper wire to the
other position.
To Red wire
of MSS
(note color)
INSTALLATION
30'
unconnected terminal.
WARNING: For indoor use only.
SELECT A LOCATION
Flip the unjumpered switch
on and off.
Remove the jumpered
switch from the
junction box.
3-Way Switch Wiring Diagram
NEW APPLICATION
Choose a location where the motion sensor has a clear view of
the entire area where occupant motion may occur.
15'
RETROFIT APPLICATION
Motion sensing switch will replace existing wall switch. Use only
where the existing switch location provides a clear view of the
occupied area.
0'
Typical Plan View of Coverage
Turn the power
off at the
circuit breaker.
Lights
turn on
and off.
Jumper is
Yes
No
correct. Go
GENERAL APPLICATION INFORMATION
The detector is more sensitive to motion across the front of the sensor than to motion towards the sensor.
to next page.
Questions? Call 1-800-435-4448 8:00 AM to 6:30 PM Eastern Time, weekdays
The detector senses heat in motion and possible heat sources that change temperature quickly. Therefore, to
avoid false triggering, avoid placing the sensor where it will be aimed at air conditioners, heaters, and other
sources of heat or cold.
598-1107-01
- 4 -
- 2 -
- 3 -
• Connect the 3-Way Motion Sensing Switch as shown in the diagram below:
Single Switch Installation
TROUBLESHOOTING
ADJUSTMENTS
HOT
≠ Replace
switch with MSS
If you have a problem with your Wall Switch, first follow this guide. If the problem persists, call the
customer service hotline at 1-800-435-4448 between 8:00 AM and 6:30 PM ET weekdays.
• For single switch installations,
TIME
LIGHT LEVEL
connect the wall switch as shown
here.
LOAD
SYMPTOM
POSSIBLE CAUSE
SYMPTOM
POSSIBLE CAUSE
Hot Wire
There are
6
preset selections for the
The sensor can be prevented from turning on lights
when there is already enough light in the room. Use a
small phillips screw driver to set the light level using this
diagram as a guide. In the fully clock-
Black
amount of time the lights stay on: Test (5
seconds), 1, 5, 10, 15, and 20 minutes. Use
a small, phillips screw driver to adjust the
TIME control (see Figure 4). Turn the TIME
control until it “snaps” into the desired time
position.
Brown
Light does not come 1. Circuit breaker or fuse is
Light does not turn
off.
1. Incorrect wiring.
2. MODE switch is set to
ON instead of AUTO.
3. Motion is still present.
4. Delay set by TIME
control has not
¨
on in the AUTO
mode.
turned off.
2. If the lamp being controlled
has another switch, it may
be turned off.
3. Bulb is defective.
4. LIGHT control is set too far
Add
Jumper
Wire
Jumpered Wire
wise position, the sensor turns on
lights even in full daylight. In the fully
counter-clockwise position, the sen-
sor only turns on lights when the sur-
OFF AUTO
ON
Hot Wire
Green ground wire to
junction box screw or
grounding wire
expired.
BLACK
rounding light level is very low.
OFF AUTO
ON
Dark (low light level)
toward the DARK position.
MODE switch is set to OFF
instead of AUTO.
Any Light Level
1. Heating or cooling ob-
jects (such as air
Light comes on for
no reason in the Auto
mode.
Green ground wire to
junction box screw or
grounding wire
5.
To adjust the photocell:
+
Red
• When the light in the room is at the
level you want the lights to turn on,
set the switch to the AUTO position.
• Put the TIME control to the 5 sec-
ond position.
• Put the LIGHT control to the mini-
mum dark (fully counter-clockwise)
position.
• Wait for the lights to turn off.
Turn the LIGHT adjustment clock-
wise in very small steps and wait 2
seconds before moving your hand
in front of the sensor. Repeat until
the lights controlled by the sensor
come on. The light will now come
on when the light level is at or below
the present level and motion is
detected.
vents, appliances, or
drafts through the wall
box) are causing false
triggering.
2. Switch on the sensor
has been turned off
and back on.
5
10
Red & Brown
6. Poor connection.
1
15
1. Motion has stopped in the
room.
TIME control is set for too
short a delay.
3-Way with Two Motion Sensors
If you want to have motion sensors at both 3-way switches, connect them as shown below. The minimum
Lights do not stay
on in the Auto mode.
Test
20
3-Way Motion Sensor Wiring Diagram
T I M E
L I G H T
2.
wattage may increase to 100 W for fluorescent and 50 W for incandescent lighting.
• Mount the MSS into the junction box with the two junction box screws.
• Turn the circuit breaker back on.
• Preset the controls: Time to min. (fully CCW), Photo Adjustment fully clockwise. Cover the lens with masking
tape.
• With the motion sensor in the "ON" position, turn the remote switch on and off several times. Go to step 1, 2,
or 3, depending on results.
5 Seconds
20 Minutes
3. There was a momen-
tary power interrup-
tion. The light will turn
off automatically when
the "on" time expires.
Common Switch Lug
HOT
HOT
SPECIFICATIONS
Electrical input................................................................................................................................120V, 60 Hz
Fluorescent Load...........................................................(2) 30 Watt minimum 400 Watt maximum Rapid Start
Motor Load.............................................................................................................................1/8 HP maximum
Incandescent.........................................................................................................................500W at 120V AC
On-Time..........................................................................................Adjustable approximately 5 sec. to 20 min.
Photocell Sensor.......................................................................................From dull daylight to less than 1 FC.
Coverage...............................................................................up to 15 ft. at 1500, up to 30 ft. in front of the sensor
WARNING: Shut off all power at fuse box or circuit breaker before beginning installation.
Exchange
3-Way
Switch
3-Way
Switch
Test again.
Go to 2 or 3.
If light does
not turn on:
Red & Black
wires on
1.
2.
3.
Complete Installation
• Replace control panel cover and install the decorative wall plate. In installations where the GE motion sensor
switch is combined with other switches or outlets on an expanded box, a combination wall plate will need to
be purchased. Various combination wall plates are available at Home Centers and Electrical Supply Stores.
MSS Control
Existing Wiring Diagram
Exchange
Red & Brown
wires on
If light turns
on in only one
position of
HOT
Test again.
Go to 1 or 3.
Red & Brown
WARNING
Red &
Brown
• Slide the switch a couple of times to make sure it operates freely.
remote switch:
MSS Control
Risk of electric shock
• Shut off power at fuse box or
circuit breaker before installation
• Use indoors only
If light turns
on with
remote switch
in either
position:
Set sensor to "AUTO". Wait for the
unit to warm up (up to 1 min.). If the
remote switch can turn the lights on,
it's OK. Otherwise:
USE
HOT
OFF AUTO
ON
OFF AUTO
ON
Black
Black
MODE Selection Switch
Moving the switch selects one of three modes of operation: OFF, AUTO, ON
Risk of fire
• Do not exceed electrical ratings
Green ground wire to
junction box screw or
grounding wire
OFF: Lights stay off.
Exchange Red & Brown wires
on MSS Control. Remove the
tape. Go to the next page.
AUTO: Lights come on for time set when motion is detected and the light level is below the set level or when
3-way switch is manually switched.
Dual 3-Way Motion Sensor Wiring Diagram
Res. #8143555
ON: Lights stay on continuously. Flipping 3-way switch has no effect.
- 7 -
- 6 -
- 8 -
- 5 -
|