Honeywell Car Video System HMLCD15 User Manual

HMLCD15  
15-inch LCD Monitor  
User Manual  
Video Systems  
1-800-796-CCTV  
© 2004 Honeywell International Inc.  
All rights reserved. No part of this publication may be reproduced by  
any means without written permission from Honeywell Video Systems.  
The information in this publication is believed to be accurate in all  
respects. However, Honeywell Video Systems cannot assume  
responsibility for any consequences resulting from the use thereof.  
The information contained herein is subject to change without notice.  
Revisions or new editions to this publication may be issued to  
incorporate such changes.  
HMMU000880 – 04/04 – Rev. A  
 
4.4  
LIMITED WARRANTY  
FCC COMPLIANCE STATEMENT  
Honeywell International Inc. ("Seller"), 1305 Waters Ridge Drive, Lewisville, TX 75057,  
warrants this monitor to be in conformance with its own plans and specifications and to  
be free from defects in materials and workmanship under normal use and service for a  
period of up to one (1) year from the date of manufacture. Seller's obligation shall be  
limited to repairing or replacing, at its option, free of charge for materials or labor, any  
product which is proved not in compliance with Seller's specifications or proves  
defective in materials or workmanship under normal use and service. Seller shall have  
no obligation under this Limited Warranty or otherwise if the product is altered or  
improperly repaired or serviced by anyone other than Honeywell factory service. For  
warranty service, return product transportation prepaid, to Honeywell Video Systems  
Factory Service, 1305 Waters Ridge Drive, Lewisville, TX 75057.  
INFORMATION TO THE USER: This equipment has been  
tested and found to comply with the limits for a Class A digital  
device, pursuant to Part 15 of the FCC rules. These limits are  
designed to provide reasonable protection against harmful  
interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful  
interference in which case the user will be required to correct  
the interference at his own expense.  
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR  
FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND  
THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE  
TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH  
OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER  
BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY  
THE SELLER'S OWN NEGLIGENCE OR FAULT.  
CAUTION: Changes or modifications not expressly approved  
by the party responsible for compliance could void the user’s  
authority to operate the equipment.  
Seller does not represent that the products it sells may not be compromised or  
circumvented; that the products will prevent any personal injury or property loss by  
burglary, robbery, fire or otherwise; or that the products will in all cases provide  
adequate warning or protection. Customer understands that a properly installed and  
maintained alarm may only reduce the risk of a burglary, robbery, fire or other events  
occurring without providing an alarm, but it is not insurance or a guarantee that such will  
not occur or that there will be no personal injury or property loss as a result.  
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY,  
PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED  
TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR  
INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED  
WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S  
MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF  
THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY  
AGAINST SELLER. This warranty replaces any previous warranties and is the only  
warranty made by Seller on this product. No increase or alteration, written or verbal, of  
the obligations of this Limited Warranty is authorized.  
This Class A digital apparatus complies with Canadian ICES-  
003.  
Cet appareil numérique de la Classe A est conforme à la norme  
NMB-003 du Canada.  
Rev. A  
20  
HMMU000880  
04/08/04  
Rev. A  
iii  
HMMU000880  
04/08/04  
 
SECTION 4:  
TROUBLESHOOTING AND MAINTENANCE  
EXPLANATION OF GRAPHICAL SYMBOLS  
The lightning flash with arrowhead symbol within  
4.1  
TROUBLESHOOTING  
an equilateral triangle is intended to alert the user  
to the presence of uninsulated "dangerous  
voltage" within the product's enclosure that may  
be of sufficient magnitude to constitute a risk of  
electric shock to persons.  
No Power  
Make sure the Power cable is plugged to the wall and the  
back of the monitor.  
The exclamation point within an equilateral  
triangle is intended to alert the user to the  
presence of important operating and  
maintenance (servicing) instruction in the  
literature accompanying the product.  
Make sure that the Power button on the front of the monitor  
is turned ON. Press the Power button firmly to turn the  
power OFF, then again to turn it ON.  
Poor Picture Quality  
If the quality of the picture is poor and cannot be improved by  
making adjustments on the front control panel, inspect all  
system connections and cable runs.  
C A U T I O N  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
4.2  
4.3  
MAINTENANCE  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER (OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
To reduce the risk of electrical shock, do not remove the cover  
or back of monitor. No user-serviceable parts are inside.  
SERVICE AND SUPPORT  
Refer servicing to qualified personnel or contact the Technical  
Support at 1-800-796-CCTV for assistance.  
Rev. A  
iv  
HMMU000880  
04/08/04  
Rev. A  
19  
HMMU000880  
04/08/04  
 
NOTES:  
WARNINGS  
Installation and servicing should be performed only by qualified  
and experienced personnel.  
TO PREVENT FIRE OR SHOCK HAZARD,  
DO NOT EXPOSE THIS PRODUCT TO RAIN OR  
MOISTURE.  
SAFEGUARDS  
This product is made with consideration of the maximum safety of  
users. However, in order to prevent all possible accidents and financial  
lost, the monitor must be installed in the appropriate environment.  
Read instructions and follow all safeguards.  
POWER WARNINGS  
1. Insert the power plug completely into the socket and verify that it is  
inserted well. An unstable connection can cause fire.  
2. Do not use a damaged power cable or plug or a loose socket.  
Doing so may cause electric shock or fire.  
3. Do not touch the plug with wet hands. Doing so may cause  
electric shock or fire.  
4. Do not overload the socket by using it for several devices at the  
same time. Doing so may cause a fire.  
ENVIRONMENT/INSTALLATION WARNINGS  
1. Do not install the unit in an extremely hot or humid location, or in a  
place subject to dust or mechanical vibration. Do not install in  
locations with oil or smoke or inside vehicles. The unit is not  
designed to be waterproof. Exposure to rain or water may damage  
the unit. Do not use this unit near water or in an unprotected  
outdoor installation, or any area which is classified as a wet  
location.  
Rev. A  
18  
HMMU000880  
04/08/04  
Rev. A  
v
HMMU000880  
04/08/04  
 
SAFEGUARDS, CONTINUED  
3.4  
GETTING OPTIMAL PICTURE  
Step 1: Window’s background or “H” character should be displayed  
2. Do not place candlelight, mosquito coils, or cigarettes on top of the  
on your screen.  
monitor or install it close to heating appliances. Doing so may  
damage the product or create a fire danger. The product should  
be situated away from heat sources such as radiators, heat  
registers, stoves, or other products (including amplifiers) that  
produce heat.  
Step 2: Adjust the screen to the center of the Display (LCD) by using  
the top and bottom display controls and the V-Position Adjust  
menu.  
3. Do not place this product on an unstable cart, stand, tripod,  
bracket, or table. Do not install in an unstable location or place the  
monitor on top of a smaller stand. The product may fall, causing  
serious injury to a child or adult and serious damage to the  
monitor."  
4. Do not leave the power cable close to any heating appliance or  
product that may generate heat. Heat-producing items can melt  
the skin of the power cable and cause electric shock or fire.  
Step 3: Adjust the screen to the center of the Display (LCD) by using  
the right and left display controls and the Horizontal size and  
H=Position Adjust menu.  
5. Power supply cords should be routed so that they are not likely to  
be walked on or pinched by items placed upon or against them,  
paying particular attention to cords and plugs, convenience  
receptacles, and the point where they exit from the unit. Do not  
bend the power cable by force or place a heavy object on it as this  
may cause electric shock or fire.  
6. When removing the power plug, hold the plug head properly.  
Pulling on the power cord itself may damage the core of the cable  
and cause heating or danger of fire.  
Step 4: Adjust the phase until the “H” character displays clearly.  
7. Remove power from the monitor when cleaning the monitor or  
around the plug. Do not use flammable spray or material when  
cleaning the monitor or place any such materials near the monitor.  
8. Slots and openings in the cabinet and the back or bottom are  
provided for ventilation and to ensure reliable operation of the  
equipment and to protect it from overheating. These openings  
must not be blocked or covered. Equipment should never be  
placed near or over a radiator or heat register. This product should  
not be placed in a built-in installation, such as a bookcase or rack  
unless proper ventilation is provided or the manufacturer’s  
instructions have been adhered to.  
H
Step 5: Using the Contrast, Brightness, and Color options,  
set the color.  
Step 6: When finished adjusting, save the settings by pressing  
the Exit key.  
Rev. A  
vi  
HMMU000880  
04/08/04  
Rev. A  
17  
HMMU000880  
04/08/04  
 
3.3  
ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE,  
CONTINUED  
SAFEGUARDS, CONTINUED  
CLEANING AND GENERAL USAGE  
Using HOTKEY  
Frequent adjustments such as auto-geometry, Brightness,  
1. For added protection of this unit during a lightning storm, or when  
it is left unattended and unused for long periods of time, unplug it  
from the wall outlet and disconnect the cable system. This will  
prevent damage to the unit due to lightning and power-line surges  
Contrast, Audio-volume, Audio-Mute, and Source (selected in  
RGB/VIDEO) can be quickly done without calling the MENU.  
The following table describes the HOTKEY.  
2. Never push objects of any kind into this unit through openings as  
they may touch dangerous voltage points or short-out parts that  
could result in a fire or electric shock. Never spill liquid of any kind  
on the unit.  
3. Do not attempt to service this unit yourself as opening or removing  
covers may expose you to dangerous voltage or other hazards.  
Refer all servicing to qualified service personnel.  
4. When moving the monitor, turn the monitor OFF, unplug the power  
cord, and make sure that all other connecting cables are  
disconnected. This will prevent electric shock or fire caused by  
cable damage.  
5. If the monitor makes an unusual noise or produces a burning odor  
or smoke, disconnect it from power immediately and contact the  
service center.  
1
2
3
4
5
6
7
6. If the monitor is not used for a long period of time, disconnect it  
from the power outlet.  
7. Consult with the service center once each year to clean the inside  
of the monitor. Accumulation of dust inside the monitor may cause  
fire or malfunction.  
OSD KEY  
BRT  
DESCRIPTION  
BRIGHTNESS  
CONTRAST  
1
2
3
4
5
CONT  
VOL  
8. Unplug the unit from the outlet before cleaning. Do not use liquid  
or aerosol cleaners. Use a clean soft cloth for cleaning. Do no use  
wax, benzene, alcohol, thinner, mosquito spray, aromatic or  
lubricating oil, or any other detergent or chemical.  
AUDIO-VOLUME  
AUDIO- MUTE  
MUTE  
SOURCE  
SELECTED IN RGB/S-VHS  
COMPOSITE  
9. Do not place the monitor face down on the floor or press on it,  
otherwise the LCD screen may be damaged.  
6
7
CH  
REFERENCE TO TV BOX MANUAL  
AUTO GEOMETRY  
10. Careless use and improper repair may cause electric shock and/or  
damage to the product. Do not open the monitor.  
AUTO  
Rev. A  
16  
HMMU000880  
04/08/04  
Rev. A  
vii  
HMMU000880  
04/08/04  
 
PURCHASE INFORMATION  
Date Purchased:  
3.3  
ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE,  
CONTINUED  
OSD Menu  
OSD  
Description  
Horizontal Position  
Vertical position  
Timeout  
Select OSD Menu horizontal position.  
Select OSD MENU vertical position.  
Time after which OSD MENU leaves screen.  
Adjust the transparency of the OSD Menu.  
Serial Number:  
Location Installed:  
Transparency  
English  
Language  
French  
German  
Italian  
Select one of the five languages.  
Spanish  
Advanced Horizontal Position  
Factory Preset  
Select OSD Menu horizontal position.  
Initialize the current mode.  
Normal state of the monitor.  
Adjust the volume level.  
Information  
Audio  
Volume  
Balance  
Treble  
Adjust the audio balance.  
Adjust the volume of the high sounds.  
Adjust the volume of the low sounds.  
Turn the sound ON or OFF.  
Selects analog signal.  
Bass  
Mute  
Input  
Select  
Analog  
S-VHS  
Video  
Selects S-VHS mode.  
Selects Video mode.  
Video  
Sharpness  
Brightness  
Contrast  
Color  
Control the outline.  
Adjust the brightness of the screen.  
Adjust the contrast of the screen.  
Adjust the saturation of Red, Green, and  
Blue in the display area.  
Hue  
Adjust the tone of color.  
Rev. A  
viii  
HMMU000880  
04/08/04  
Rev. A  
15  
HMMU000880  
04/08/04  
 
3.3  
ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE,  
CONTINUED  
TABLE OF CONTENTS  
SECTION 1: INTRODUCTION ............................................................... 1  
OSD Menu Description  
1.1 INTRODUCTION ..........................................................................1  
The following table describes the OSD menu and a description  
of each option.  
1.2 FEATURES...................................................................................1  
1.3 TFT LCD PANEL...........................................................................2  
1.4 CONTENTS OF PACKAGE ..........................................................3  
OSD Menu  
Description  
Picture  
Auto adjustment  
Automatically adjusts the Horizontal  
position, Vertical position, horizontal  
size and Phase. Windows  
SECTION 2: CONTROLS AND CONNECTIONS .................................. 5  
background or characters should be  
displayed on the full screen prior to  
processing this function.  
2.1 CONTROLS – FRONT PANEL......................................................5  
2.2 CONTROLS – REAR PANEL ........................................................6  
2.3 INSTALLING THE MONITOR DRIVER..........................................7  
2.4 VGA CABLE..................................................................................7  
Horizontal position  
Vertical position  
Horizontal size  
Phase  
Adjust the horizontal position of the  
screen’s image.  
Adjust the vertical position of the  
screen’s image.  
Adjust the horizontal size of the  
screen’s image.  
SECTION 3: OPERATION..................................................................... 9  
3.1 POWER MANAGEMENT..............................................................9  
Adjust the focus of the screen’s  
image.  
3.2 PRESET MODE CHART.............................................................10  
DOS/Graphics  
Select priority of DOS mode/ Graphic  
mode.  
Timing Charts ...........................................................................10  
Input Timing Limits...................................................................10  
Input Level Limits......................................................................10  
Preset Mode Table ...................................................................11  
Color  
Auto adjustment  
Brightness  
Adjust the color balance of the screen.  
Adjust the brightness of the screen.  
Adjust the contrast of the screen.  
3.3 ON-SCREEN DISPLAY (OSD) CONTROL  
Contrast  
PROCEDURE .............................................................................12  
Temperature 6500k  
9300k  
Control the temperature of the color  
On-Screen Display (OSD) Control Adjustment........................13  
OSD Menu Description.............................................................14  
Using HOTKEY.........................................................................16  
User Red  
Green  
Blue  
Control the intensity of the color of the  
screen’s image.  
3.4 GETTING OPTIMAL PICTURE ...................................................17  
Rev. A  
14  
HMMU000880  
04/08/04  
Rev. A  
ix  
HMMU000880  
04/08/04  
 
TABLE OF CONTENTS, CONTINUED  
3.3  
ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE,  
CONTINUED  
SECTION 4: TROUBLESHOOTING AND MAINTENANCE................. 19  
4.1 TROUBLESHOOTING................................................................19  
On-Screen Display (OSD) Control Adjustment  
No Power..................................................................................19  
Poor Picture Quality..................................................................19  
Æ
Æ
Æ
Æ
Æ
Å
o
Start  
OSD  
pq  
Move  
Menu  
Item  
o
Select  
Menu  
Item  
pq  
Select  
SubMenu  
Item  
o
pq  
Select  
Menu  
Item  
Adjust  
the  
4.2 MAINTENANCE..........................................................................19  
4.3 SERVICE AND SUPPORT..........................................................19  
4.4 LIMITED WARRANTY.................................................................20  
Value  
È
Å
n
Exit the  
OSD  
n
Return  
to  
n
Return  
to  
SECTION 5: SPECIFICATIONS........................................................... 21  
Menu  
Menu  
Rev. A  
x
HMMU000880  
04/08/04  
Rev. A  
13  
HMMU000880  
04/08/04  
 
SECTION 1:  
INTRODUCTION  
3.2  
PRESET MODE CHART, CONTINUED  
The monitor is compatible with additional modes within one of  
the following specified frequency ranges, provided they are  
different at least for one of the following:  
1.1  
INTRODUCTION  
Honeywell's HMLCD15 TFT Color LCD Display features a 15.0"  
viewable active matrix LCD screen, with outstanding 1024 x 768  
pixel resolution. When used in PC based applications the  
HMLCD15 provides connection points for VGA, PC Sound, and  
headphones. CCTV applications are supported by input  
connections for audio, Y/C (S-Video) and composite video  
sources while providing a flicker free viewing experience not  
normally experienced with traditional CRT-type monitors. Easy  
to access front panel OSD display controls including direct  
contrast, brightness, volume and mute control buttons along  
with single button source selection for quick and easy  
adjustments.  
Horizontal Frequency: ±1 KHz  
Vertical Frequency: ±1 Hz  
3.3  
ON-SCREEN DISPLAY (OSD) CONTROL PROCEDURE  
Image and sound can easily be adjusted through an OSD menu.  
4
3
2
1
1.2  
FEATURES  
XGA (1024x768) resolution LCD module  
16,777,216 Color Display  
DPMS (Display Power Management Signaling)  
OSD (On-Screen Display) controls  
Multi-language OSD Menu  
1
2
3
AUTO / EXIT  
MENU / SEL  
CH Z  
Used to exit OSD  
Used to start the OSD and select options  
Utilizes DDC1/2B controls. The system will perform Plug &  
Play feature if both monitor and host system support  
DDC1/2B protocol.  
Menu move/adjust buttons.  
Used to move the menu bar or adjust  
values.  
4
SOURCE Y  
Internal speakers  
Rev. A  
12  
HMMU000880  
04/08/04  
Rev. A  
1
HMMU000880  
04/08/04  
 
3.2  
PRESET MODE CHART, CONTINUED  
1.3  
TFT LCD PANEL  
Preset Mode Table  
Black spots (pixels that do not light) or luminescent spots (pixels  
that are always lit) may appear on the screen because of the  
intrinsic characteristics of TFT LCD technology. This is neither a  
malfunction nor a defect in the monitor. The warranty period for  
the occurrence of black spots and luminescent spots is 1 month  
from the date of purchase. Monitors with less than 3 such pixels  
will not be exchanged.  
Horizontal  
Pixel  
640  
640  
640  
640  
720  
800  
800  
Frequency  
KHz 31.444 31.469 37.862 37.500 31.440 35.156 37.879  
Period (T1)  
ms  
ms  
ms  
ms  
ms  
31.778 31.778 26.413 26.667 31.778 28.444 26.400  
2.542 3.813 1.270 2.032 3.813 2.000 3.200  
3.178 1.907 4.064 3.810 1.907 3.556 2.200  
25.422 25.422 20.317 20.317 25.422 22.222 20.000  
0.635 0.636 0.762 0.508 0.636 0.667 1.000  
Sync Width (T2)  
Back Poach (T3)  
Active (T4)  
Front Poach (T5)  
Vertical  
Frequency  
Period (T1)  
Sync Width (T2)  
Back Poach (T3)  
Active (T4)  
Front Poach (T5)  
Interlaced  
Line  
Hz  
ms  
ms  
ms  
ms  
ms  
Y/N  
H
350  
480  
480  
480  
400  
600  
600  
70.087 59.940 72.539 75.000 70.087 56.250 60.317  
14.268 16.683 13.735 13.333 14.268 17.778 16.579  
0.095 0.064 0.079 0.080 0.064 0.057 0.106  
1.905 1.048 0.739 0.427 1.080 0.626 0.607  
11.136 15.253 12.678 12.800 12.711 17.067 15.840  
1.145 0.318 0.237 0.027 0.413 0.028 0.026  
N
P
N
The HMLCD15 uses high-voltage fluorescent tubes. If a portion  
or whole of the screen becomes dark or flickers intermittently,  
the monitor can be exchanged for free. Contact Customer  
Service within one year of purchase date.  
N
N
N
N
N
N
N
N
N
N
N
P
N
P
P
N
P
P
Sync Polarity  
V
When the HMLCD15 is not in use, the screen must be turned off  
or the pattern must be frequently changed by using a screen  
saver. If the same pattern is displayed on the screen for a long  
period of time, image sticking may occur or the life of the  
monitor may be shortened.  
Horizontal  
Frequency  
Period (T1)  
Sync Width (T2)  
Back Poach (T3)  
Active (T4)  
Pixel  
800  
800  
832  
1024  
1024  
1024  
KHz 48.077 46.875 49.726 48.363 56.476 60.023  
ms  
ms  
ms  
ms  
ms  
20.800 21.333 20.110 20.677 17.707 16.660  
2.400 1.616 3.910 2.092 1.813 1.219  
1.280 3.232 1.117 2.462 1.920 2.235  
16.000 16.162 14.524 15.754 13.653 13.653  
1.120 0.323 0.559 0.369 0.320 0.203  
Front Poach (T5)  
Vertical  
Frequency  
Period (T1)  
Sync Width (T2)  
Back Poach (T3)  
Active (T4)  
Front Poach (T5)  
Interlaced  
Line  
Hz  
ms  
ms  
ms  
ms  
ms  
Y/N  
H
600  
600  
624  
768  
768  
768  
72.188 75.000 74.552 60.004 70.069 75.029  
13.853 13.333 13.414 16.666 14.272 13.328  
0.125 0.064 0.060 0.124 0.106 0.050  
0.478 0.448 0.784 0.600 0.513 0.466  
12.480 12.800 12.549 15.880 13.599 12.795  
0.770 0.021 0.020 0.062 0.053 0.017  
N
P
P
Some computer systems are not compatible  
with the DDC standard. If your monitor is  
displaying the wrong resolution, check your  
computer system for a DDC compatible video  
card and contact the Service Center.  
N
P
P
N
-
-
N
N
N
N
N
N
N
P
P
Sync Polarity  
V
Rev. A  
2
HMMU000880  
04/08/04  
Rev. A  
11  
HMMU000880  
04/08/04  
 
3.2  
PRESET MODE CHART  
1.4  
CONTENTS OF PACKAGE  
1. LCD Monitor 2. User Manual  
3. VGA Cable  
Timing Charts  
The monitor shall be capable of supporting the following video  
timings:  
VIDEO  
SYNC  
(T4) Active  
(T3) Back Poach  
(T5) Front Poach  
Synch Width (T2)  
4. Sound Cable  
5. AC/DC  
Adapter  
6. Installation  
Disk  
(T1) Period  
Input Timing Limits  
H-Sync Pulse Width 1.0 µs Sync Pulse Width 6.0 µs.  
V-Sync Pulse Width 0.04ms Sync Pulse Width 0.5ms  
7. Power Cord  
8. Video Sound Cable  
NOTE: If the width of Sync Pulse is out of input timing range,  
the monitor may operate abnormally. Check Sync  
Pulse Width of Input Timing.  
Input Level Limits  
9. Composite Cable  
10. BNC to RCA Adapters (2)  
Low level:  
High level:  
0.4V (Max)  
2.4V (Min)  
NOTE: For better quality display image, use the timing and  
polarity shown in the preset mode table. Refer to your  
video card’s user guide to ensure compatibility.  
OPTIONAL ACCESSORIES: S-video cable, Wall Mount  
adapter (VESA standard)  
Rev. A  
10  
HMMU000880  
04/08/04  
Rev. A  
3
HMMU000880  
04/08/04  
 
SECTION 3:  
OPERATION  
NOTES:  
3.1  
POWER MANAGEMENT  
This monitor is equipped with DPMS (Display Power  
Management Signaling) function which automatically switches  
to power saving mode (less than 5 watts consumed) when the  
computer is left unattended. Although the monitor can be left in  
power saving mode for longer periods, it is recommended that  
you turn it off after your daily work.  
The DPMS function requires support from the computer system  
of any software DPMS function currently being used. If the  
keyboard (or mouse) is left unattended for a certain period, the  
program or system will set the sync signals to SPMS modes.  
The DPMS function has three states. Recommended signals,  
power consumption, and recovery time are shown in the table  
below:  
Signal  
Power  
Recovery  
LED  
Status  
On  
Consumption Time  
Indicator  
HSync VSync Video  
Pulse Pulse Active  
30Watt  
--  
Green  
Alternating  
Green/Orange  
(1sec)  
No  
Standby  
Pulse Blank  
Pulse  
Less than  
5Watt  
Within  
2sec  
Alternating  
Green/Orange  
(0.5sec)  
No  
Pulse  
Suspend Pulse  
Blank  
Blank  
No  
No  
Off  
Orange  
Pulse Pulse  
Rev. A  
4
HMMU000880  
04/08/04  
Rev. A  
9
HMMU000880  
04/08/04  
 
NOTES:  
SECTION 2:  
CONTROLS AND CONNECTIONS  
2.1  
CONTROLS – FRONT PANEL  
A
B
C
D
E
F
G
H
J
I
K
A
B
C
D
E
AV1  
PC  
F
G
H
I
AUTO/EXIT  
BRT Y  
LAMP  
SOURCE Y  
CH Z  
CONT Z  
VOL Y  
MENU/SEL  
J
MUTE Z  
K
POWER BUTTON  
Rev. A  
8
HMMU000880  
04/08/04  
Rev. A  
5
HMMU000880  
04/08/04  
 
2.2  
CONTROLS – REAR PANEL  
2.3  
INSTALLING THE MONITOR DRIVER  
D
C
B
E
A
You can achieve an optimal resolution and scanning rate by  
installing the monitor driver as follows:  
F
G
1. Insert the monitor driver diskette into the floppy diskette  
drive and run INSTALL.EXE.  
2. Select the monitor model then press OK.  
The installation will begin immediately.  
2.4  
VGA CABLE  
DVR or VCR  
PC  
A 15-pin D-Sub connector is used as the input signal connector.  
Pin and input signal are shown in the table below.  
Pin Name  
Pin Name  
Pin Name  
A
DC12V  
B
C
D
E
F
Ear  
1
4
7
Red  
2
5
8
Green  
3
6
9
Blue  
PC Sound  
VGA  
N.C  
GND  
RED-GND  
+5V  
GREEN-GND  
BLUE-GND  
Video Sound  
S-VHS  
10 Logic-GND  
13 H-sync  
11 N.C  
12 SDA (DDC)  
15 SCL (DDC)  
AV1  
14 V-sync  
G
Composite  
Rev. A  
6
HMMU000880  
04/08/04  
Rev. A  
7
HMMU000880  
04/08/04  
 

Graco Baby Jumper 1762254 User Manual
Grizzly Welder H3266 User Manual
Hamilton Beach Coffeemaker 47334C User Manual
Harbor Freight Tools Home Safety Product 03358 User Manual
Heath Zenith Work Light SL 5503 User Manual
HP Hewlett Packard Cell Phone Accessories 8935 User Manual
HP Hewlett Packard Laptop xe310 User Manual
Husqvarna Chainsaw 575XP User Manual
IBM Laptop 46P4547 User Manual
IKEA Indoor Furnishings AA 171181 1 User Manual