FFU3D W
English
Operating Instructions
REFRIGERATOR/FREEZER COMBINATION
Contents
Operating Instructions, 1
Assistance, 2
Description of the appliance, 3
Installation, 4
Accessories, 5
Start-up and use, 6
Maintenance and care, 7
Precautions and tips, 8
Troubleshooting 9
Description of the appliance
Control panel
1 FREEZER OPERATION Button to regulate the temperature the
freezer compartment. Button is used with SUPER FREEZE
Button to switch on/switch off the product by pressing both 3
seconds
2 SUPER FREEZE Button (rapid freezing) to freeze fresh food.
Press button for 3 seconds to switch on the product while it is
switched off
3 SUPER FREEZE Blue light illuminates when SUPER FREEZE
button is pressed.
4 FREEZER TEMPERATURE Yellow light The temperature of the
Freezer is consisted with 4 levels as indicated on serigraphy
5 FRIDGE TEMPERATURE Yellow light The temperature of the
Fridge is consisted with 4 levels as indicated on serigraphy
6 SUPER COOL Blue light illuminates when SUPER COOL button
is pressed.
7 SUPER COOL Button (quick cool) to lower the temperature of
the refrigerator compartment rapidly.
8 REFRIGERATOR OPERATION button to regulate the
temperature of the refrigerator compartment.
!The indicator lights are also used to indicate an unusual temperature
increase in the freezer compartment (see Troubleshooting).
3
6
5
4
2
4
6
8
26 22 20 18
°C
°C
SUPER
FREEZE
SUPER
COOL
1
7
2
8
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
3
Description of the appliance
Overall view
The instructions contained in this manual are applicable to different
model refrigerators. The diagrams may not directly represent the
appliance purchased. For more complex features, consult the
following pages.
1 Levelling FEET
2 FREEZER and STORAGE compartment
3 BOTTLE shelf*
4 Food Care Zone / Food Care Zone 0°C / Safe Defrost*
5 FRUIT and VEGETABLE bin*
6 Removable multipurpose SHELVES*
7 Control panel.
8 WINE RACK*
*Varies by number and/or position, available only on certain
models.
7
6
5
6
8
3
3
4
2
1
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
4
If a replacement fuse cover is fitted, it must be of the correct colour
as indicated by the coloured marking or the colour that is
embossed in words on the base of the plug.
Installation
GB
Changing the plug:
Removing the plug
If your appliance has a non-rewireable moulded plug and you should
wish to remove it to add a longer cable or to re-route the mains cable
through partitions, units etc. please ensure that either:
! Before placing your new appliance into operation please read
these operating instructions carefully. They contain important
information for safe use, for installation and for care of the
appliance.
! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.
Positioning and connection
-
The plug is replaced by a fused 13amp re-wireable plug
bearing the BSI mark of approval.
or
-
Positioning
The mains cable is wired directly into a 13amp cable outlet,
controlled by a switch (in compliance with BS 5733) which is
accessible without moving the appliance.
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to operate
correctly and save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm between
the sides and any furniture/side walls.
Disposing of the plug
Cut off and dispose of the supplied plug if it does not fit your socket.
The cable should be cut as close as possible to the moulded plug.
4. Ensure the appliance is away from any sources of heat (direct
sunlight, electric stove, etc.).
Remove the fuse.
5. In order to maintain the correct distance between the appliance
and the wall behind it, fit the spacers supplied in the installation
kit, following the instructions provided.
WARNING:
To avoid a shock hazard do not insert the discarded plug
into a socket anywhere else.
Levelling
Fitting a new plug
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
IMPORTANT:
WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE
WITH THE FOLLOWING CODE...
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical socket
ensure the following:
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the appliance,
which is indicated on the data plate located on the bottom left
side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values indicated on
the data plate located on the bottom left side (e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If the
socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use extension
cords or multiple sockets.
Green and Yellow - Earth
Blue
Brown
- Neutral
- Live
! Once the appliance has been installed, the power supply cable
and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised
technicians only (see Assistance).
As the colours of the wires in the mains lead may not correspond
with the coloured markings identifying the terminals in your plug,
proceed as follows:
-
Connect Green and Yellow wire to terminal marked 'E' or
or
! The manufacturer declines any liability should these safety
measures not be observed.
coloured Green and Yellow.
-
-
Connect Brown wire to terminal marked 'L' or coloured red or
brown.
Connect Blue wire to terminal marked 'N' or coloured Black or
Blue.
Your appliance is supplied with a 13amp fused plug that can be
plugged into a 13amp socket for immediate use. Before using the
appliance please read the instructions below.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
If a 13amp plug (BS 1363) is used it must be fitted with a 13amp fuse.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
Replacing fuse covers:
When replacing a faulty fuse, a 13amp ASTA approved fuse to BS
1362 should always be used and the fuse cover re-fitted.
If the fuse cover is lost, the plug must not be used until a
replacement is obtained.
CE Marking certifies that this appliance conforms to the
following EEC directives:
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/
68/EEC
Replacement fuse covers:
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
5
1. Insert the plug into the socket and switch on the product using
the appropriate button, ensure that yellow refrigerator and
freezer temperature lights illuminates
Installation
GB
2. After a few hours you will be able to put food in the refrigerator.
3. Press the SUPER FREEZE button (rapid freezing): the SUPER
FREEZE indicator light will illuminate. Once the refrigerator has
reached the optimal temperature, the indicator light goes out
and you can begin food storage.
! Beforeplacingyournewapplianceintooperationpleasereadthese
operatinginstructionscarefully. Theycontainimportantinformationfor
safeuse, forinstallationandforcareoftheappliance.
! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.
Chiller system
NO FROST
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to operate
correctly and save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm between
the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat (direct
sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the appliance
and the wall behind it, fit the spacers supplied in the installation
kit, following the instructions provided.
The No Frost system circulates cold air continuously to collect
humidity and prevent ice and frost formation. The system maintains
an optimal humidity level in the compartment, preserving the
original quality of the food, preventing the food from sticking
together and making defrosting a thing of the past. Do not block
the aeration cells by placing food or containers near the
refrigerating back panel.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
Electrical connections
! Close bottles and wrap food tightly.
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical socket
ensure the following:
Using the refrigerator to its full potential
• Use the REFRIGERATOR OPERATION button to adjust the
temperature (see Description).
• Press the SUPER COOL button (rapid cooling) to lower the
temperature quickly. For example, when you place a large
number of new food items inside a fridge the internal
temperature will rise slightly. The function quickly cools the
groceries by temporarily reducing the temperature until it
reaches the ideal level.
• Place only cold or lukewarm foods in the compartment, not hot
foods (see Precautions and tips).
• Remember that cooked foods do not last longer than raw foods.
• Do not store liquids in open containers. They will increase
humidity in the refrigerator and cause condensation to form.
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the appliance,
which is indicated on the data plate located on the bottom left
side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values indicated
on the data plate located on the bottom left side (e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If the
socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power supply cable
and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! To close the refrigerator door to pay attention to the vertical
bracket position (see figure)
! The cable must be checked regularly and replaced by authorised
technicians only (see Assistance).
! The manufacturer declines any liability should these safety
measures not be observed.
Start-up and use
Starting the appliance
! Before starting the appliance, follow the installation
instructions (see Installation).
! Before connecting the appliance, clean the compartments and
accessories well with lukewarm water and bicarbonate.
! The appliance comes with a motor protection control system which
makes the compressor start approximately 8 minutes after being
switched on. The compressor also starts each time the power supply
is cut off whether voluntarily or involuntarily (blackout).
SHELVES: Due to the special guides the shelves are removable
and the height is adjustable, allowing easy storage of large
containers and food.
*Varies by number and/or position, available only on certain
models.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
6
FRUIT and VEGETABLE bin*
Hidden Shelf*
GB
The salad crispers fitted inside the fridge have been specially
designed for the purpose of keeping fruit and vegetables fresh
and crisp. Open the humidity regulator (position B) if you want to
store food in a less humid environment like fruit, or close it (position
A) to store food in a more humid environment like vegetable.
There is wireshelf inside the freezer compartment located between
the upper and lower freezer baskets. To Access wire shelf, remove
the basket of the upper freezer door. Wire shelf may be removed
out of the freezer by holding up from the front edge.
It is recommended to use the wire shelf only for long term storage.
A
A
B
B
TEMPERATURE Indicator light*: to identify the coldest area in the
refrigerator.
ICE DEVICE*
1. Check that OK appears clearly on the indicator light (see
diagram).
After pouring water in the special ice cups, place them in their
places in the ice device. After about 2 hours, the ice cubes will be
ready. In order to get the ice cubes, it will be sufficient to turn the
two buttons to the right. The ice cubes will fall in to the tray below,
ready to be used.
2. If the word “OK” does not appear it means that the temperature
is too high: set a lower temperature and wait approximately 10
hours until the temperature has been stabilised.
3. Check the indicator light again: if necessary, readjust it following
the initial process. If large quantities of food have been added or
if the refrigerator door has been opened frequently, it is normal
for the indicator not to show OK. Wait at least 10 hours before
adjusting the REFRIGERATOR OPERATION knob to a higher
setting.
Using the freezer to its full potential
• Use the FREEZER OPERATION button to adjust the temperature
(see Description).
• Do not re-freeze food that is defrosting or that has already been
defrosted. These foods must be cooked and eaten (within 24
hours).
• Fresh food that needs to be frozen must not come into contact
with food that has already been defrosted.
• Do not place glass bottles which contain liquids, and which are
corked or hermetically sealed in the freezer because they could
break.
• The maximum quantity of food that may be frozen daily is
indicated on the plate containing the technical properties located
on the bottom left side of the refrigerator compartment (for
example: Kg/24h: 4).
• To freeze (if the freezer is already operating): press the rapid
freezing SUPER FREEZE button (corresponding blue indicator
light illuminates), insert the food and close the door. The function
is disabled automatically after 24 hours or when optimal
temperatures have been reached (indicator light goes out)
If you need more storage space, the ICE DEVICE may be taken out
by pushing the nail on the top of the ice device.
Food Care Zone *
Area dedicated to the storage of fresh food, such as meat and
fish. Thanks to the low temperature inside the compartment, the
Food Care Zone extends the period of time for which the food
can be stored, keeping it fresh for up to a week.
Food Care Zone 0°C / Safe Defrost* :
A compartment designed to keep delicate food such as meat
and fish fresh. The low temperature in the compartment (-2 / +3°
C) makes it possible to store the food for up to one week - tests
performed on meat products - without changing its nutrients,
appearance and flavour.
The compartment is also very suitable for healthy food
defrosting, as low-temperature defrosting prevents any
proliferation of microorganisms, while protecting its taste and
organoleptic properties.
! Do not store food too large in the upper freezer drawer if is
present the ‘Ice Device”.
! Do not open the door during freezing.
! If there is a power cut or malfunction, do not open the freezer
door. This will help maintain the temperature inside the freezer,
ensuring that foods are conserved for at least 9 -14 hours.
*Varies by number and/or position, available only on certain
models.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
7
It is not suitable for fruit, vegetables and green salad. But it can
be used for fresh or very fresh dairy products and milk, stuffed
fresh pasta and even cooked food or leftovers.
GB
Maintenance and care
Switching the appliance off
During cleaning and maintenance it is necessary to disconnect the
appliance from the electricity supply:
1. press the FREEZER OPERATION Button and SUPER FREEZE
Button for 3 seconds to switch off the product
2. pull the plug out of the socket
Precautions and tips
! If this procedure is not followed, the alarm may sound. This alarm
does not indicate a malfunction. To restore normal operation insert
the plug into the socket, press the FREEZER OPERATION and
SUPER FREEZE button and set the FREEZER OPERATION button
on the desired value.To disconnect the appliance, follow point 1
and 2.
! The appliance was designed and manufactured in compliance
with international safety standards. The following warnings are
provided for safety reasons and must be read carefully.
This appliance complies with the following Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
amendments;
-89/336/EEC of 03.05.89 (Electromagnetic Compatibility) and
subsequent amendments;
Cleaning the appliance
• The external and internal parts, as well as the rubber seals may
be cleaned using a sponge that has been soaked in lukewarm
water and bicarbonate of soda or neutral soap. Do not use
solvents, abrasive products, bleach or ammonia.
- 2002/96/CE..
• The removable accessories may be soaked in warm water and
soap or dishwashing liquid. Rinse and dry them carefully.
• The back of the appliance may collect dust which can be
removed by delicately using the hose of a vacuum cleaner set
on medium power. The appliance must be switched off and the
plug must be pulled out before cleaning the appliance.
• During the cleaning of the slide rails for the drawers in the
freezer compartment, it may happen that the automatic drawer
closure mechanism is deactivated. To reactivate it, simply close
the drawer a little more forcefully than is usually necessary.
Avoiding mould and unpleasant odours
• The appliance is manufactured with hygienic materials which are
odour free. In order to maintain an odour free refrigerator and to
prevent the formation of stains, food must always be covered or
sealed properly.
General safety
• The appliance was designed for domestic use inside the home
and is not intended for commercial or industrial use.
• The appliance must be used to store and freeze food products
by adults only and according to the instructions in this manual.
• The appliance must not be installed outdoors, even in covered
areas. It is extremely dangerous to leave the appliance exposed
to rain and storms.
• Do not touch the appliance with bare feet or with wet or moist
hands and feet.
• Do not touch the internal cooling elements: this could cause skin
abrasions or frost/freezer burns.
• When unplugging the appliance always pull the plug from the
mains socket, do not pull on the cable.
• Is not sufficient to switch-off of the product to eliminate all the
electrical connections.
• If you want to switch the appliance off for an extended period of
time, clean the inside and leave the doors open.
• In the case of a malfunction, under no circumstances should you
attempt to repair the appliance yourself. Repairs carried out by
inexperienced persons may cause injury or further
malfunctioning of the appliance.
• Do not use any sharp or pointed utensils or electrical equipment
- other than the type recommended by the manufacturer - inside
the frozen food storage compartments.
I Care function
The I Care function can be enabled to optimise energy
consumption. Press and hold down the SUPERCOOL and
REFRIGERATOR OPERATION buttons simultaneously for at least 6
seconds to enable this function.
On enabling the function, 4 indicator lights will go on for 2 seconds:
SUPER COOL light, SUPER FREEZE light and two temperature
lights - one for the refrigerator and one for the freezer.
After 5 seconds the interface will enter the energy saving mode and
the indicator lights will go off. The interface stays off even when the
door is opened. Just press any button to switch it on again. Press
the adjustment buttons to change the temperature.
Consumption will be optimised 48h after the function was enabled.
To disable the I Care function, switch off the product (see
description). The product can be switched on again for normal
operation.
• Do not put ice cubes taken directly from the freezer into your
mouth.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or lack of experience
and knowledge unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to
ensure that they do not play with the appliance.
• Keep packaging material out of the reach of children! It can
become a choking or suffocation hazard.
In humid environments, when the I Care function is enabled, slight
condensation may form on the doors; normal operating conditions
are restored when the function is disabled.
Disposal
• Observe local environmental standards when disposing
packaging material for recycling purposes.
Replacing the light bulb
• The European Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE), requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream.Old appliances must be collected
Thanks to the powerful light it emits, the new LED lighting system
offers a clear view of all foods, with no shadowy areas. If the LED
needs to be replaced, please contact the Technical Assistance
Service.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
8
separately in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human health
and the environment.
The refrigerator and the freezer do not cool well.
• The doors do not close properly or the seals are damaged.
• The doors are opened too frequently.
GB
The crossed out “wheeled bin” symbol on the product reminds
you of your obligation, that when you dispose of the appliance it
must be separately collected. Consumers should contact their
local authority or retailer for information concerning the correct
disposal of their old appliance.
• The refrigerator or the freezer have been over-filled.
The food inside the refrigerator is beginning to freeze.
• The temperature is not adjusted properly (see description)
• The food is near the back inside wall of the refrigerator.
The motor runs continuously.
Respecting and conserving the environment
• Install the appliance in a fresh and well-ventilated room. Ensure
that it is protected from direct sunlight and do not place it near
heat sources.
• Try to avoid keeping the door open for long periods or opening
the door too frequently in order to conserve energy.
• Do not fill the appliance with too much food: cold air must
circulate freely for food to be preserved properly. If circulation is
impeded, the compressor will work continuously.
• The SUPER FREEZE button has been pressed (rapid freezing):
the blue SUPER FREEZE light is on (see Description).
• The door is not closed properly or is continuously opened.
• The outside ambient temperature is very high.
The appliance makes a lot of noise.
• The appliance has not been installed on a level surface (see
Installation).
• The appliance has been installed between cabinets that vibrate
and make noise.
• Do not place hot food directly into the refrigerator. The internal
temperature will increase and force the compressor to work
harder and will consume more energy.
• The internal refrigerant makes a slight noise even when the
compressor is off. This is not a defect, it is normal.
Troubleshooting
If the appliance does not work, before calling for Assistance (see
Assistance), check for a solution from the following list.
.
Any indicator lights do not illuminate.
• If the function I Care is not active (see section), the plug has not
been inserted into the electrical socket, or not far enough to
make contact, or there is no power in the house.
The motor does not start.
• The appliance comes with a motor protection control (see Start-
up and use).
The indicator lights are on but the light is dim.
• Pull out and reverse the plug before putting it back in the socket.
a) The alarm sounds.
• The refrigerator door has remained open for more than two
minutes (the buzzer will stop sounding when you shut the door) or
the correct switching-off procedure was not followed (see
Maintenance).
b) The alarm sounds and the two blue indicator lights flash.
The temperature in the freezer is too high. Check the quality of
the food products and dispose if necessary.
•
+ buzzer = Heating is excessive
c) The alarm sounds and the two blue indicator and green
one lights flash.
• The temperature in the freezer has reached a dangerous level.
The food must be disposed immediately.
+ buzzer = Heating danger
b/c) In both these cases the freezer will maintain a temperature of
about 0°C so that the food does not re-freeze.
To turn off the acoustic signal open and close the refrigerator door.
restore normal operation product should be switched off and
switched on by buttons from control panel (See the description)
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
9
GB
10
GB
11
195105680.02
02/2013
GB
12
|