Instructions for use
WASHER-DRYER
!
This symbol reminds you to read this booklet.
GB
Contents
GB
Installation, 2-3-4-5
Unpacking and levelling
English,1
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 6
Cutting off the water or electricity supply
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 7
General safety
WDAL 9640
Disposal
Opening the porthole door manually
Description of the washer-dryer and
starting a wash cycle, 8-9
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 10
Table of wash cycles
Personalisation, 11
Setting the temperature
Setting the drying cycle
Functions
Detergents and laundry, 12
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system
Troubleshooting, 13-14
Assistance, 15-16
1
Connecting the drain hose
Connect the drain
• the supply voltage is included within the
values indicated on the Technical Data Plate
fixed on the machine.
GB
hose, without ben-
ding it, to a draining
duct or a wall drain
situated between 65
and 100 cm from the
floor;
• the socket is compatible with the washer-
dryer’s plug. If this is not the case, replace
the socket or the plug.
65 - 100 cm
Your appliance is now supplied with a 13 amp
fused plug it can be plugged into a 13 amp
socket for immediate use. Before using the
appliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE
EARTHED.
The drain hose may
be connected to
an under-sink trap.
Before connecting
the drain hose from
the machine ensure
that any blanks or
removable ends have
been taken off the
spigot.
THE FOLLOWING OPERATIONS SHOULD
BE CARRIED OUT BY A QUALIFIED ELECTRI-
CIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be
used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a
replacement is obtained.
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be
of the correct colour as indicated by the colou-
red marking or the colour that is embossed in
words on the base of the plug. Replacements
can be obtained directly from your nearest
Service Depot.
If it is placed over
the edge of a basin
or sink be sure the
free end of the hose
should not be under-
water.
Removing the plug:
If your appliance has a non-rewireable moul-
ded plug and you should wish to re-route the
mains cable through partitions, units etc.,
please ensure that either:
the plug is replaced by a fused 13 ampere
rewireable plug bearing the BSI mark of ap-
proval.
! We advise against the use of hose extensions;
in case of absolute need, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Ensure that if the drain hose is pushed into
a standpipe, that the end does not go down
more than 15cms (6 inches). If the hose is pu-
shed down too far, this may cause the machine
to self -syphon ie. continuously empty as it is
filling.
or:
the mains cable is wired directly into a 13
amp cable outlet, controlled by a switch, (in
compliance with BS 5733) which is accessible
without moving the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot
be accidentally inserted into a socket.
Electric connection
Instructions for connecting cable to an alternati-
Before plugging the appliance into the mains
socket, make sure that:
ve plug:
Important: the wires in the mains lead are co-
loured in accordance with the following code:
Green & Yellow Earth
• the socket is earthed and in compliance with
the applicable law;
Blue
Brown
Neutral
Live
• the socket is able to sustain the appliance’s
maximum power load indicated on the Tech-
nical Data Plate fixed on the machine;
3
As the colours of the wires in the lead may not
correspond with the coloured markings iden-
tifying the terminals in your plug, proceed as
follows:
! The power supply cable must only be repla-
GB
ced by an authorised serviceman.
Warning! The company denies all liability if and
when these norms are not respected.
Connect Green & Yellow wire to terminal
marked E or or coloured Green or Green &
Yellow.
The first wash cycle
Connect Brown wire to terminal marked L or
coloured Red.
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
programme “Auto Clean” (see “Cleaning the
washer-dryer”).
Connect Blue wire to terminal marked N or
coloured Black.
If a 13 amp plug (BS 1363) is used it must be
fitted with a
13 amp fuse, either in the plug or adaptor or
at the distribution board.
If you are in any doubt regarding the electrical
supply to your machine, consult a qualified
electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
NEUTRAL (N)
LIVE (L)
EARTH (E)
BROWN
GREEN & YELLOW
GREEN &
YELLOW
13 ampere fuse
BROWN
CROSS-BAR
CORD GRIP
BLUE
Disposing of the appliance:
When disposing of the appliance please re-
move the plug by cutting the mains cable as
close as possible to the plug body and dispo-
se of it as described on the previous page.
! The washer-dryer should not be installed in
an outdoor environment, not even where the
area is sheltered, because it may be very dan-
gerous to leave it exposed to damp, rain and
thunderstorms.
! When the washer-dryer is installed, the mains
socket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent
or dangerously compressed.
4
Technical data
GB
Model
WDAL 9640
width 59.5 cm
Dimensions height 85 cm
depth 54 cm
from 1 to 9 kg for the wash
programme
Capacity
Electrical
from 1 to 6 kg for the drying
programme
please refer to the technical
connections data plate fixed to the machine
maximum pressure
1 MPa (10 bar)
Water con-
minimum pressure
nections
0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed up to 1400 rotations per minute
Wash: programme 4; tempe-
rature 60°C; using a load of
9 kg.
Energy ra-
ted
Drying: the smaller load
must be dried by selecting
programmes the dryness level. The load
according to must consist of 3 sheets,
regulation
EN 50229
2 pillowcases and 1 hand
towel;
the remainder of the load
must be dried by selecting
the dryness level.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU
5
Care and maintenance
Cutting off the water and electri-
city supplies
Cleaning the pump
GB
The washer-dryer is fitted with a self-cleaning
pump which does not require any maintenan-
ce. Sometimes, small items (such as coins or
buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
• Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system
inside the washer-dryer and help to prevent
leaks.
• Unplug the washer-dryer when cleaning it
and during all maintenance work.
! Make sure the wash cycle has finished and
unplug the appliance.
Cleaning the washer-dryer
To access the pre-chamber:
• The outer parts and rubber components
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
• The washer-dryer has a “Auto Clean” pro-
gramme for its internal parts that must be run
with no load in the drum.
1. using a screwdri-
ver, remove the cover
panel on the lower
front part of the
washer-dryer (see
figure);
To help the wash cycle you may want to use
either the detergent (i.e. a quantity 10% the
quantity specified for lightly-soiled garments)
or special additives to clean the washer-dryer.
We recommend running a cleaning program-
me every 40 wash cycles.
2. unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;
To start the program-
A
B
me press buttons A
and B simultaneously
for 5 seconds (see
figure).
The programme will
start automatically
and will run for about
70 minutes. To stop
the cycle press the
START/PAUSE button.
3. clean the inside thoroughly;
4. screw the lid back on;
Cleaning the detergent dispenser
drawer
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Remove the dispen-
1
ser by raising it and
pulling it out (see
figure).
Checking the water inlet hose
Wash it under running
water; this operation
should be repeated
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
frequently.
2
! Never use second-hand hoses.
Caring for the door and drum of
your appliance
• Always leave the porthole door ajar in order
to prevent unpleasant odours from forming.
6
Precautions and tips
! This washer-dryer was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
Disposal
GB
•Disposing of the packaging materials: observe local regu-
lations so that the packaging may be re-used.
•The European Directive 2012/19/EU on Waste Electrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the im-
pact on human health and the environment. The crossed
out “wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the appliance it
must be separately collected. Consumers should contact
their local authority or retailer for information concerning the
correct disposal of their old appliance.
General safety
• This appliance is not intended for use by persons (inclu-
ding children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsi-
ble for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
– Do not dry unwashed items in the tumble dryer.
– Items that have been soiled with substances such as
cooking oil, acetone, alcohol, petrol, kerosene, spot re-
movers, turpentine, waxes and wax removers should be
washed in hot water with an extra amount of detergent
before being dried in the tumble dryer.
– Items such as foam rubber (latex foam), shower caps,
waterproof textiles, rubber backed articles and clothes
or pillows fitted with foam rubber pads should not be
dried in the tumble dryer.
– Fabric softeners, or similar products, should be used
as specified by the fabric softener instructions.
– The final part of a tumble dryer cycle occurs without
heat (cool down cycle) to ensure that the items are left
at a temperature that ensures that the items will not be
damaged.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if it
is not, remove excess water
using the drain hose, collec-
ting it in a bucket as indicated
in the figure.
WARNING: Never stop a tumble dryer before the end
of the drying cycle unless all items are quickly removed
and spread out so that the heat is dissipated.
• This appliance was designed for domestic use only.
• Do not touch the machine when barefoot or with wet or
damp hands or feet.
• Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
3. using a screwdriver,
remove the cover panel on
the lower front part of the
washer-dryer (see figure).
• Do not touch the drained water as it may reach extre-
mely high temperatures.
• Never force the porthole door. This could damage the safety
lock mechanism designed to prevent accidental opening.
• If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt
to repair it yourself.
• Always keep children well away from the appliance while
it is operating.
• If it must be moved, proceed with the help of two or th-
ree people and handle it with the utmost care. Never try
to do this alone, because the appliance is very heavy.
• Before loading laundry into the washer dryer, make sure
the drum is empty.
• During the drying phase, the door tends to get quite hot.
• Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
• Do not use the appliance to dry foam rubber or
similar elastomers.
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
• Make sure that the water tap is turned on during
the drying cycles.
7
Description of the washer-dryer
and starting a wash cycle
Control panel
WASH CYCLE
PROGRESS indicator lights
GB
DRYING knob
DOOR
ON/OFF button
TEMPERATURE
knob
LOCKED
indicator light
START/PAUSE
button with indicator
light
FUNCTION
buttons with
indicator lights
Detergent dispenser drawer
WASH CYCLE
knob
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened.
To start the wash cycle from the point at which it was
interrupted, press this button again.
ON/OFF button: switches the washer-dryer on and off.
WASH CYCLE knob: programmes the wash cycles. Du-
ring the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
Standby mode
This washer-dryer, in compliance with new energy saving
regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).
Consumption in off-mode: 0.5 W
Consumption in Left-on: 8 W
DRYING knob: used to set the desired drying programme
(see “Personalisation”).
WASH CYCLE PROGRESS indicator lights: used to
monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
8
Door locked indicator light
Indicator lights
GB
If this indicator light is on, the appliance door is locked to
prevent it from being opened accidentally; to avoid any
damage, wait for the indicator light to switch off before you
open the appliance door.
The indicator lights provide important information.
This is what they can tell you:
Wash cycle phase indicator lights
! If the START/PAUSE indicator light (orange) flashes
rapidly at the same time as the function indicator light, this
indicates a problem has occurred (see “Troubleshooting”).
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to indicate
which phase of the cycle is currently in progress.
Wash
Rinse
Note: as soon as a drying
Spin
level or time period has
been set, this indicator light
illuminates to indicate that the
selected wash cycle will be
followed by a drying phase.
Drying
End of wash cycle
END
Note: during the “Drain” phase, the indicator light corre-
sponding to the “Spin” cycle phase will illuminate.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the pro-
grammed wash cycle, the corresponding indicator light will
flash and a sound alert (3 beeps); the function will not be
activated.
If a function which is incompatible with another function
selected previously, only the most recent selection will
remain active.
Starting a wash cycle
1. Turn the washer-dryer on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds, then only
the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indicator light will flash.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the drying cycle if necessary (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed
manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the
indicator light will switch on. The DOOR LOCKED indicator light will switch off, indi-
cating that the door may be opened. Take out your laundry and leave the appliance door ajar to make sure the drum dries
completely. Switch the washer-dryer off by pressing the ON/OFF button.
9
Wash cycles
Table of wash cycles
GB
Detergents
Fabric
Max.
Max.
Max.
load
(kg)
Cycle
duration
Description of the wash cycle
temp. speed Drying
(°C)
(rpm)
Wash
softener
CLEAN Plus
1
2
3
4
5
6
6
Anti Stain
40°
60°
90°
60°
40°
60°
40°
1400
1400
1400
1400
1400
800
5
5
9
9
9
4
4
180’
180’
180’
185’
180’
115’
110’
Whites
Cottons: extremely soiled whites.
Cottons (1): heavily soiled whites and resistant colours.
Cottons (2): lightly soiled resistant colours.
Synthetics: heavily soiled resistant colours.
Synthetics (3): heavily soiled resistant colours.
SPECIALS
800
7
8
9
Anti Allergy
60°
40°
30°
1400
800
0
5
2
1
195’
90’
Wool: for wool, cashmere, etc.
Delicates
80’
Fastwash 30’: to refresh lightly soiled garments quickly
(not suitable for wool, silk and clothes which require washing by hand).
10
30°
30°
800
3,5
1
30’
45’
11 Ready to Wear 45’
DRYING
1400
12 Drying Cottons
-
-
-
-
-
-
-
-
-
-
-
-
6
4
2
-
-
-
13 Drying Synthetics
14 Drying Wool
Partials cycles
Rinse
-
-
1400
1400
-
-
36’
16’
9
9
Spin+Pump out
-
The length of cycle shown in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors
such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 4 with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle 5 with a temperature of 40°C.
3) Long wash cycle for synthetics: set wash cycle 6 with a temperature of 40°C.
Anti Stain: the programme 1 is suitable to heavily-soiled garments with resistant colours. It ensures a washing class that is
higher than the standard class (A class). When running the programme, do not mix garments of different colours. We recom-
mend the use of powder detergent. Pre-treatment with special additives is recommended if there are obstinate stains.
Whites: use this cycle 2 to wash white clothes. The programme is designed to maintain the brightness of white clothes over
time. Use powder detergent for best results.
If the drying function is selected, a drying cycle automatically activates at the end of the wash cycle that resembles open-air
drying, with the added advantages of preserving garments from yellowing due to sunlight exposure and preventing loss of
whiteness caused by the possible presence of dust in the air. Drying cycles can only be selected on a level basis.
Anti Allergy: use programme 7 to remove major allergens such as pollen, mites, cat’s and dog’s hair.
Ready to Wear: select programme 11 for washing and drying lightly soiled garments (Cotton and Synthetic) in a short time.
This cycle may be used to wash and dry a laundry load of up to 1 kg in just 45 minutes.
To achieve optimum results, use liquid detergent and pre-treat cuffs, collars and stains.
10
Personalisation
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash ( ). The washer-dryer will automatically prevent you from
selecting a temperature which is higher than the maximum value set for each wash cycle.
GB
Setting the drying cycle
Table of Drying times (guideline values)
Turn the DRYING knob to set the desired drying type.
Fabric
type
Max.
load (kg) dry
Cupboard Henger Iron
Two options are available:
Load type
dry
dry
A - Based on time: from 40 to 180 minutes.
B - Based on the how damp the clothes are once they
have been dried:
Clothing of diffe-
rent sizes, Terry
towels
Cotton
6
200
180
145
Iron : slightly damp clothes, easy to iron.
Hanger
: dry clothes to put away.
Synthe-
tics
Sheets, Shirts, Py-
jamas, socks, etc.
4
2
205
155
190
150
170
135
Cupboard : very dry clothes, recommended for towel-
ling and bathrobes.
If your laundry load to be washed and dried is much gre-
ater than the maximum stated load (see adjacent table),
perform the wash cycle, and when the cycle is complete,
Knitwear, Pullo-
vers. etc.
Wool
divide the garments into groups and put some of them back in the drum. At this point, follow the instructions provided for a
“Drying only” cycle. Repeat this procedure for the remainder of the load.
N.B: when the drying is complete there is a cooling period, even though the DRYING knob is in the
position.
Drying only
Turn the WASH CYCLE knob to one of the drying settings (12-13-14) according to the type of fabric, then select the desired
drying duration using the DRYING knob.
Selecting the cotton drying cycle (
position) through the programme selector knob and pressing the “Eco” button activates an
automatic drying cycle that allows for saving energy, thanks to an optimal combination of air temperature and cycle duration.
Functions
The various wash functions available with this washer-dryer will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the
selected wash cycle.
Super Wash
This option offers a high-performance wash due to the greater quantity of water used in the initial phase of the cycle, and due
to the increased wash cycle duration, is particularly useful for the removal of stubborn stains.
! This function may not be used in conjunction with wash cycles 2, 7, 8, 9, 10, 11, 12, 13, 14,
.
Slow Spin
By selecting this function, reduces the spin speed.
! This function may not be used in conjunction with wash cycles 7, 9, 11, 12, 13, 14.
Timer Saver
If you select this option, the wash cycle duration will be reduced by up to 50%, depending on the selected cycle, thereby gua-
ranteeing simultaneous water and energy saving. Use this cycle for lightly soiled garments.
! This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 11, 12, 13, 14,
,
.
Eco
The Eco option saves energy by not heating the water used to wash your laundry – an advantage both to the environment
and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash results in the same avera-
ge time of a standard cycle. For the best washing results we recommend the usage of a liquid detergent
! This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 11, 13, 14,
,
.
By also turning the DRYING knob to the position, a drying cycle automatically activates at the end of the wash cycle that
also helps to reduce energy consumption, thanks to an optimal combination of air temperature and cycle duration.
! It can be activated with programmes 4 and 5.
11
Detergents and laundry
Detergent dispenser drawer
Garments requiring special care
GB
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in fact
cause build up on the inside of your appliance and contri-
bute to environmental pollution.
Wool: the wool wash cycle on this Hotpoint machine has
been tested and approved by The Woolmark Company
for washing wool garments labelled as hand washable
provided that the garments are washed according to the
instructions on the garment label and those issued by the
manufacturer of this washer-dryer. Hotpoint is the first
washer-dryer brand to be approved by The Woolmark
Company for Apparel Care- Platinum for its washing per-
formance and consumption of energy and water. (M1127)
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent dispenser
drawer and pour in the deter-
gent or washing additive, as
follows.
A
B
In UK, Eire, Hong Kong and India the Woolmark trade mark
is a Certification trade mark.
Delicates: use programme 10 to wash very delicate
garments with decorative features, such as diamantes and
sequins.
*
1
2
We recommend turning the garments inside out before
washing and placing small items into the special bag for
washing delicates.
When selecting an exclusively time-based drying function,
a drying cycle is performed at the end of the wash cycle
that is particularly delicate, thanks to light handling and
appropriate temperature control of the water jet.
The recommended durations are:
1 kg of synthetic garments --> 150 min
1 kg of synthetic and cotton garments --> 180 min
1 kg of cotton garments --> 180 min
! Do not pour detergent into the middle compartment (*).
Detergent should only be poured into the compartment 1.
compartment 1: Detergent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage.
If powder detergent is used, place the partition into slot B.
compartment 2: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
The degree of dryness depends on the load and fabric
composition.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washer-dryer performs the distribution process instead of
spinning. To encourage improved load distribution and bal-
ance, we recommend small and large garments are mixed
in the load.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
• Do not exceed the values listed in the “Table of wash cycles”,
which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
12
Troubleshooting
Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that
the problem cannot be solved easily using the following list.
GB
Problem:
Possible causes / Solutions:
The machine does not switch on.
• The appliance is not plugged into the socket fully, or not enough to make contact.
• There is no power to the socket, or the fuse has blown in the mains plug.
The wash cycle does not start.
• The door is not closed properly.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap has not been turned on to allow water to flow into the machine.
The machine does not fill with wa-
• The water inlet hose is kinked.
ter or the indicator light for the first • The water inlet hose is not connected to the water supply.
wash cycle stage flashes rapidly.
• The water pressure is too low.
• The water tap has not been turned on to allow water to flow into the machine.
• There is no water supply to the house.
• The inlet valve filter is blocked.
• The START/PAUSE button has not been pressed.
The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65
water and continually drains away
or Water left in the drum
or Stuck on wash.
and 100 cm from the floor (see “Installation”).
• The drain hose is connected incorrectly to the sink trap allowing water to run
into the machine, the drain hose must be positioned higher than the bottom of
the sink to prevent water flowing down the drain hose.
• The end of the drain hose has been pushed too far down the standpipe, the
‘U’ bracket should be fitted 100 mm from the end of the drain hose.
The machine does not drain or
spin.
• The Pump filter is blocked.
• The drain hose is kinked (see “Installation”).
• New Installation - The blanking cap or spigot has not been removed if con-
nected under a sink.
• The drain hose or sink trap is blocked.
• The wash cycle does not include draining, some wash cycles require the drain
phase to be started manually.
The machine does not heat or poor • The ‘Temperature’ selector knob is in the “ ” position.
wash results.
The programme takes too long.
• Programme times will vary due to water pressure, the incoming water tempe-
rature and if the wash load goes out of balance. This will increase the pro-
gramme times accordingly (see ‘ The machine wont spin properly’ below).
The machine vibrates a lot during
the spin cycle.
• The feet have not been adjusted, enabling the machine to rock.
• New Installation - Either the Transit Bolts including the plastic spacers, or the
Polystyrene Packaging have not been removed when installing the machine.
• The machine is trapped between cabinets and/or walls.
• The load is in a slight out of balance condition and machine is spinning, but at
a lower speed.
• The appliance is not plugged into the socket, or not enough to make contact.
• There has been a power failure.
The washer-dryer does not dry.
• The appliance door is not shut properly.
• A DELAY TIMER has been set.
• DRYING is in the
position.
13
The machine is noisy.
• There will always be some motor, pump and drum noise during spin.
GB
The machine wont spin properly.
• Out of Balance detected when attempting to go into a spin cycle - If this
happens the machine will continue to try to repeat the distribution of the load
required before the machine will go into higher spin speeds - This will increase
the programme time accordingly. This is a safety feature to prevent damage.
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,
etc). - Try the programme again using a different load.
The machine leaks from the
dispenser.
• The dispenser drawer is blocked with detergent and requires cleaning.
• The water pressure is too high and requires turning down - turn down the tap
on the water supply pipe slightly and try again.
• The machine is tilting forwards - It must be level when in its final position.
The machine leaks (other than
dispenser).
• The fill hose is loose, check both the cabinet and tap ends.
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill
hose is missing the rubber washer.
• The drain hose is not fixed in properly.
The indicator lights on the console
are flashing rapidly.
• Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again If the problem persists contact the Technical Assistance
Service.
The machine smells.
• The machine requires a service wash. Run a “Auto Clean” wash cycle with
detergent and no laundry.
The machine door cannot be
opened.
• The door will not open until the door lock indicator light goes out shortly after
the program has finished.
Door Seal damaged at the bottom.
• The door seal has drainage holes at the bottom - This is normal.
• The water level is correct if it can be seen at the bottom of the door.
The water level is too low when
the machine is washing.
There is too much foam.
• The detergent is not suitable for machine washing (it should display the text
‘for washer-dryers’ or ‘hand and machine wash’ or the like).
• Too much detergent was used - less detergent is required in soft water.
After completing the programme,
or before starting a programme,
the machine has turned itself off
(no lights).
• To comply with new energy saving regulations the machine is fitted with an
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate
the machine, it can then either be switched off or a new programme selected.
General.
• Your washer-dryer contains sensors that monitor progress during the wash
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro-
gress).
Normally, if your machine successfully completes the cycle, there is unlikely to
be anything wrong!
Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.
14
Assistance
Guarantee
12 Months Parts and Labour Guarantee
GB
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs
for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of
either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost
to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise
interfered with by any person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result
of improper installation.
Replacement of any consumable item or accessory . These include but are not limited to: plugs,
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL
OR NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will
be a charge for our engineer’s time. To activate the extra parts warranty on your appliance, simply call our
registration line on 08448 24 24 24 (ROI 01 230 0800).
Extended Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair
bills for the life of your policy. To find the ideal plan for you please call our advice line on
08448 226 226 (Republic of Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where
necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will replace your
machine or, if you prefer, give you your money back.
15
195106255.01
04/2014
-
Xerox Fabriano
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its working
life than us - the manufacturer.
GB
Essential Contact Information
Hotpoint Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000
fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee
you must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17
Recycling & Disposal Information
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use
quality, recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the
door, plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure
that the appliance can no longer be plugged into a mains socket, and the door cannot be locked shut.
16
|