Owner’s Guide
fOr MOdel 90245
HUNTERS HIGH VELOCITY FAN
44806
04/02/2008
WelCome
unpaCkIng
Thank you for choosing a Hunter
Fan. This manual gives you complete
instructions for using your fan.
As you unpack the fan, save the carton
and packing materials in case you want to
move or ship the unit in the future.
Carefully remove all items from
the box.
Before using your fan, record the following
information for your records and for
warranty assistance.
NOTE: It is best to have someone hold
the box while you lift the fan and the
protective packaging out of the carton.
Model Name ______________________
Date Code ________________________
Date Purchased____________________
Where Purchased __________________
_________________________________
Make sure all shipping materials are
removed from fan before operating.
please attach your
receipt or a copy of your
receipt to this manual for
future reference.
[3]
44806
04/02/2008
groundIng InStruCtIonS
This appliance is for household use only
LINE CORD SAFETY TIpS
and may be plugged into any 120-volt
AC electrical outlet (ordinary household
current). DO NOT use any other type of
outlet.
1. NEVER pull or yank on the cord or
the appliance.
2. To insert plug, grasp it firmly and
guide it into the outlet.
3. To disconnect the appliance, grasp
the plug and remove it from the
outlet.
WarnIng
This unit is suitable for
grounded receptacle use only.
4. Before each use, inspect the line
cord for cuts and/or abrasion marks.
If any are found, the appliance
should be serviced and the line
cord replaced. Please return it to
our Service Department or to an
authorized service representative.
The power cord has a grounded plug
as shown in Figure 1A. The fan must be
plugged into an electrical outlet that can
accommodate the grounding pin. If your
electrical outlet can not accommodate the
grounding pin, then you must purchase
and install one of the two types of
5. NEVER wrap the cord tightly around
the appliance, as this could place
undue stress on the cord where
it enters the appliance and could
cause it to fray and break.
adapters shown in Figure 1B.
Grounded
Plug
6. DO NOT operate appliance if the
line cord shows any damage, if the
appliance works intermittently or
stops working entirely.
Grounding
Pin
Grounded
Outlet
Figure 1A
Grounded
Outlet
Adapter
(Sold Separtely)
Grounding
Means
Figure 1B
[4]
44806
04/02/2008
aSSembly
1. Remove the 2 Pre-Installed Bolts [a]
of the right end of the unit, with the
included Allen Wrench [b]. The allen
wrench is located inside the electrical
box cover (see figure 3 below).
[a]
[b]
[a]
2. Attach the Wheel Bracket Assembly
[a] using the Longer Bolts [b] provided
in the sack parts and tighten using the
allen wrench provided.
[b]
[a]
3. Store the Allen Wrench [a] in the cover
of the electrical box. This wrench
can be used to adjust the tilt / swivel
resistance (see page 6).
[a]
[5]
44806
04/02/2008
operatIon
ELECTRICAL BOX
• Grounded
• Circuit breaker protected with 7A
overcurrent protection [a].
NOTE: If the breaker trips, unplug all
cords and hit the reset button on the side
of the box.
[a]
ADJUSTING
TILT /SWIVEL RESISTANCE
[a]
1. The cover of the electrical box holds
the allen wrench needed for this
operation (see page 5, step 3).
2. To adjust tilt resistance locate
fasteners on both sides of the fans [b].
• To increase tilt resistance - turn
clockwise.
• To decrease tilt resistance - turn
counter-clockwise.
[b]
[b]
[b]
3. To adjust swivel resistance locate
fasteners along the handle above
each fan [a].
• To increase swivel resistance - turn
clockwise.
• To decrease swivel resistance - turn
counter-clockwise.
FAN SpEED
1. Each fan can be independtly
operated.
2. Use speed control rotary knob to
control the fans 3 speeds: High,
Medium, and Low.
[6]
44806
04/02/2008
Storage
1. ALWAYS store the fan in a dry place.
2. NEVER store the fan while it is still plugged in.
3. NEVER wrap the cord tightly around the fan.
4. DO NOT put any stress on the cord where it enters the fan, as it could cause the cord
to break.
maIntenanCe
This fan is permanently lubricated and will not require additional lubrication (oil) for the life
of the fan.
This fan requires little maintenance and contains no user serviceable parts. DO NOT try to
fix it yourself. Contact qualified service personnel if servicing is needed.
TO CLEAN:
1. Before cleaning, turn the fan off and remove the plug from electrical outlet. Wipe off
excess dust with a lint-free cloth.
2. DO NOT immerse the fan in water or any other liquid.
troubleShootIng
pROBLEm
SOLUTION
• Can not adjust the angle of the fan.
• Loosen the swivel and tilt bolts with
provided allen wrench
• Fan will not tilt
• Loosen tilt.
• Fan will not stay upright.
• Fan will not swivel.
• Tighten tilt.
• Loosen swivel.
• Tighten swivel.
• Reset circuit breaker.
• Fan will not hold horizontal position.
• Electrical box has no power.
If you have tried these troubleshooting
solutions and still have trouble, visit our
or call 888-830-1326 for Technical Assistance
from 7 AM to 7 PM Central Time Monday thru
Friday and 8 AM to 5 PM Central Time on
Saturday.
HUNTER FAN COMPANY
2500 FRISCO AVENUE
MEMPHIS, TN 38114, USA
®
2008 Hunter Fan Co.
©
[7]
44806
04/02/2008
|