Hunter Light Fixture
Installation Instructions
43540-01 04/24/2008
If you are installing this light fixture on a Hunter Original Ceiling Fan,
refer to the “For Hunter Original Ceiling Fans Only” section.
1. Disconnect power to the ceiling fan by turning off the circuit breakers
both to the outlet box and to its associated wall switch location.
2. Remove the lower switch housing by unscrewing the three screws from
the upper switch housing. Disconnect the 9-pin plug connectors.
3. Push the plug button from inside the lower switch housing to remove the
plug button and switch housing cap.
Note: Save the plug button and switch housing cap should you choose to
remove the light fixture in the future.
4. Feed the two wires from the light fixture through the center hole in the
lower switch housing.
5. Attach the light fixture to the lower switch housing with the two screws
included with the light fixture. Securely tighten the two screws.
WARNING: Improper installation could cause the light fixture to fall.
6. Remove the wire nut from the black/white wire in the lower switch hous-
ing. Use this wire nut to connect the black/white wire from the lower
switch housing to the black wire from the light fixture. Remove the wire
nut from the white wire in the lower switch housing. Use this wire nut to
connect the white wire from the lower switch housing to the white wire
from the light fixture.
Lower
Switch
Housing
Lower
Switch
Housing
Light
Fixture
Switch
Housing
Cap
Steps 2-3
Plug
Button
Steps 4-5
7. Connect the 9-pin plug connectors. Attach the lower switch housing to
the upper switch housing with the three previously removed screws.
8. Install 2 - 60 W Max B-10 Candelabra bulbs.
9. Attach the 8” extension chain to the fan pull chain.
10. read the light pull chain through the center hole in the adapter, cap and
finial. read the fan pull chain through the side hole in the adapter and
cap.
11. Place the glass bowl and cap over the threaded rod.
12. Screw the finial onto the end of threaded rod to secure the glass bowl.
Note: If the glass bowl is crooked, you can loosen the finial and adjust the
glass bowl until it is level. Once level, securely tighten the finial.
13. Restore power to the ceiling fan.
Upper
Switch
Housing
Glass
Bowl
Cap
Lower
Switch
Housing
Finial
Step 7
Steps11-12
For Hunter Original Ceiling Fans Only:
1. Disconnect power to the ceiling fan by turning off the circuit breakers both to the
outlet box and to its associated wall switch location.
2. Remove the switch housing cover by unscrewing the two screws.
Note: Save the switch housing cover and two screws should you choose to remove
the light fixture in the future.
3. Feed the two wires from the light fixture through the center hole in the switch hous-
ing cover (included with the light fixture).
4. Remove the wire nut from the black/white wire in the switch housing. Use this wire
nut to connect the black/white wire from the switch housing to the black wire from
the light fixture. Remove the wire nut from the white wire in the switch housing.
Use this wire nut to connect the white wire from the switch housing to the white
wire from the light fixture.
5. Attach the light fixture to the switch housing with the two screws, included with the
light fixture, aligning the holes in the light fixture, switch housing cover, and switch
housing. Securely tighten the two screws.
WARNING: Improper installation could cause the light fixture to fall.
Continue with Step 8.
For Hunter Original
Ceiling Fans Only:
For Hunter Original
Ceiling Fans Only:
Switch
Housing
Switch
Housing
Cover (in-
cluded with
the light
fixture)
Light
Fixture
Switch
Housing
Cover
Steps 3-5
Step 2
Hunter Fan Company
2500 Frisco Avenue
Memphis,Tennessee 38114
is Light Fixture weighs 2.5 lbs.
© 2008 Hunter Fan Company
Printed in China & Taiwan
|