Hunter Fan Outdoor Ceiling Fan 43506 01 r032907 User Manual

10” Opal Schoolhouse Globe Light Kit  
Installation Instructions  
43506-01 r032907  
 
Installing the Light Kit on Fans with Removable Switch Housings  
1. Unscrew the three screws from the upper switch housing. Disconnect  
the 9-pin plug connectors. Remove the lower switch housing.  
I
O
2. Push the plug button from inside the lower switch housing to remove  
the plug button and switch housing cap. Unscrew the two attachment screws on the  
bottom of the switch housing.  
NOTE: Save the plug button and switch housing cap should you choose to remove  
the light fixture in the future.  
3. Feed the two wires from the light kit up through the center hole in the lower switch  
housing.  
Removable Switch Housing  
CAUTION: If your fan is operated by remote control, take care not to damage  
the small components on the circuit board inside the housing.  
Align the keyholes of the light kit and the screw holes of the lower switch housing.  
Install the nut and washer onto the threaded rod from the light kit.  
9-Pin Plug  
Connector  
Finish attaching the light kit to the lower switch housing. Use the two attachment  
screws removed from the lower switch housing and the lock washers on the red  
tag. Partially install the screws into the light kit and the housing. Rotate the housing  
counterclockwise until the screws are locked into the narrow ends of the keyhole  
slots. Securely tighten the two screws.  
Screw  
Attachment  
Screw  
WARNING: Improper installation could cause the light fixture to fall, or result  
in electrical shock or personal injury.  
Lower Switch  
Housing  
Steps 1–2  
Plug  
4. Remove the wire nuts from the two wires in the switch housing labeled “Connect  
Light Here” or “For Light Use.”  
Connect the black/white striped wire from the switch housing to the black wire from  
the light kit. Connect the white wire from the switch housing to the white wire from  
the light kit. Secure all wire connections using wire nuts.  
To connect the wires, hold the bare metal leads together and place a wire nut over  
them, then twist the wire nut clockwise until tight.  
CAUTION: Be sure no bare metal  
wires or wire strands are visible after  
making the connections.  
Wires and  
Wire Nuts  
5. Reconnect the 9-pin plug connector.  
6. Install screws to reattach the lower  
switch housing to the upper switch  
housing.  
Attachment  
Screws and  
Lockwashers  
7. Go to the instructions for Installing  
the Bulbs, Chains, and Globe.  
9-Pin Plug  
Connector  
Step 3  
Screw  
Steps 4–6  
43506-01 r032907  
 
Installing the Light Kit on Fans with Non-Removable Switch Housing  
1. Uninstall the two screws from the switch housing cover.  
I
O
2. Remove the plug or screw from the center of the switch housing  
cover.  
3. read the switch housing cover onto the wires from the light kit. Align the large  
ends of the keyholes in the light kit with the screw holes in the switch housing cover.  
Install the nut and washer onto the threaded rod from the light kit to secure the  
switch housing cover.  
4. Finish attaching the light kit to the switch housing cover. Use the two attachment  
screws removed from the lower switch housing and the lock washers on the red  
tag. Partially install the screws into the light kit and the housing. Rotate the housing  
counterclockwise until the screws are locked into the narrow ends of the keyhole  
slots. Securely tighten the two screws.  
Non-Removable Switch Housing  
WARNING: Improper installation could cause the light fixture to fall, or result  
in electrical shock or personal injury.  
5. Remove the wire nuts from the two wires in the switch housing labeled “Connect  
Light Here” or “For Light Use.” One wire is white and the other wire is black/white  
striped.  
Switch  
Housing  
Cover  
Connect the black/white striped wire from the switch housing to the black wire from  
the light kit. Connect the white wire from the switch housing to the white wire from  
the light kit. Secure all wire connections using wire nuts.  
To connect the wires, hold the bare metal leads together and place a wire nut over  
them, then twist the wire nut clockwise until tight.  
Steps 1–2  
Screw  
Plug  
CAUTION: Be sure no bare metal wires  
or wire strands are visible after making the  
connections.  
Switch  
Housing  
Cover  
Nut and  
Washer  
6. Align the locator posts in the switch housing  
cover with the screw holes in the switch  
housing.  
Screw  
Hole  
7. Align the threaded screw holes in the switch  
housing cover with the threaded holes in the  
switch housing and install two screws.  
8. Go to the instructions for Installing the Bulbs,  
Chains, and Globe.  
Wires and  
Wire Nuts  
Light Kit  
Mounting  
Plate  
Steps 5–7  
Steps 3–4  
43506-01 r032907  
 
Installing the Light Kit on Fans With Non-Removable Switch Housing  
and No Center Hole  
I
O
1. Uninstall the two screws from the switch housing.  
2. Remove the wire nuts from the two wires in the switch housing labeled  
“Connect Light Here” or “For Light Use.” One wire is white and the other wire is  
black/white striped.  
Connect the black/white striped wire from the switch housing to the black wire from  
the light kit. Connect the white wire from the switch housing to the white wire from  
the light kit. Secure all wire connections using wire nuts.  
To connect the wires, hold the bare metal leads together and place a wire nut over  
them, then twist the wire nut clockwise until tight.  
Hunter original and non-  
removable switch, no center hole  
CAUTION: Be sure no bare metal wires or wire strands are visible after making  
the connections.  
3. Finish attaching the light kit to the switch housing. Use the two screws removed  
from the switch housing and the lock washers on the red tag. Partially install the  
screws into the light kit and the housing. Rotate the light fixture clockwise until the  
screws are locked into the narrow ends of the keyhole slots. Securely tighten the two  
screws.  
WARNING: Improper installation could cause the light fixture to fall, or result  
in electrical shock or personal injury.  
4. Go to the instructions for Installing the Bulbs, Chains, and Globe.  
Wires and  
Wire Nuts  
Screws  
and  
Screw  
Washers  
Switch  
Housing  
Plate  
Light Kit  
Mounting Plate  
Step 3  
Step 1  
Step 2  
43506-01 r032907  
 
Installing the Bulbs, Chains, and Globe  
1. Install one 19-watt compact fluorescent light bulb (included) into the socket.  
2. Loosen the three thumb screws in the light kit. Raise the glass globe to the light  
fixture, fitting the rim into the louvered edge. Ensure that the top edge of the globe  
clears the screws. Hand tighten the thumb screws.  
3. Attach the provided breakaway connector onto the end of the pull chain.  
4. e installation is complete and you can restore power to the ceiling fan.  
Steps 1–4  
Hunter Fan Company  
2500 Frisco Avenue  
Memphis, Tennessee 38114  
Troubleshooting  
For other problems or questions, contact the  
Light does not come on.  
Hunter Fan Company Technical Support at  
US 888-830-1326 / Canada 866-268-1936.  
1. Make sure bulbs are installed properly and filament is not blown.  
2. Make sure breakers or fuses are on.  
3. Verify that the light power lead is connected at the ceiling. Refer to  
your ceiling fan manual for locating assembly and wiring.  
Glass rattles.  
1. Make sure the glass globe is secure.  
© 2007 Hunter Fan Company  
Printed in China  
43506-01 r032907  
 

Graco Automobile Parts 205394 Series E User Manual
Graco Baby Gym 9757 User Manual
Harbor Freight Tools Air Compressor 92720 User Manual
Harbor Freight Tools Kitchen Utensil 42787 User Manual
Hotpoint Freezer FFA64 User Manual
HP Hewlett Packard Personal Computer A7857 90023 User Manual
HP Hewlett Packard Projector MP3800 User Manual
Hubbell Lawn Mower UH32 User Manual
Husqvarna Trimmer J123L User Manual
Icom Satellite Radio S 14217HZ C1 User Manual