Husky Flooring 16628 User Manual

Important! Please follow these instructions. This kit may be different from the one specified in instruction booklet.  
07/31/2006  
COMBINATION 8X8 and 10X8 FLOOR KIT  
This floor kit will build either the 10’ wide or 8’ wide x 7’ 8-5/8” deep floor size  
FOR MARCO SERIES, SOLAR SHED AND MWP IMPERIAL ONLY  
This floor kit is for 10’ x 7’ 8-5/8” and 8’ x 7’ 8-5/8” buildings. Please refer to the appropriate pages  
of this instruction manual to build the floor size needed. If constructing an 8X8 storage building,  
you will have additional material which can be used to construct a shelf (some cutting required)  
or other projects.  
-
B E F O R E Y O U B E G I N  
-
Tools required  
First...  
Hammer  
Level  
Read these instructions thoroughly before you begin  
assembly. Assembly is easiest if you follow the steps in  
the order shown.  
Pencil  
Tape Measure  
Lumber is graded from only one side. Check the part for  
the most attractive face and make sure to face it to the  
outside.  
Optional tools  
Chalk Line  
Check all parts  
Compare parts you have to the list on page 2. If a part is  
missing, circle the part in question in the parts list and  
call us toll-free at 1-800-437-0784.  
Square  
Nail Pouch  
Saw  
8x8  
Assistance required  
We recommend that you assemble this floor on level  
ground in the location it will be used. Assistance is  
necessary to handle, fit, and secure some components.  
Two people maybe needed for some steps.  
See pages 2-3-4  
Squareness is very Important!  
Keeping all 90° corners and 90° perpendiculars square  
throughout the assembly of this floor kit will make each  
succeeding step easier and is necessary to assure that  
all components fit together properly.  
Check local zoning  
Before starting construction, check with your local  
building code official for any required permits, variances,  
etc.  
10x8  
See pages 5-6  
Check floor kit size  
Before starting construction on your floor, make sure  
that you check in the instruction manual to ensure that  
you are building the correct size floor kit for your  
building.  
Always wear OSHA-APPROVED safety  
glasses throughout assembly process  
#16628  
1
 
8X8 FLOOR KIT INSTRUCTIONS  
CONTINUED  
FLOOR PANEL ATTACHMENT:  
C:  
Position a 48 x 92-5/8” Floor  
A
Panel  
flush to the outside  
edges of sides and back of  
Floor Frame. Secure panel with  
two 2” nails at outside corners  
and one 2” nail at other  
corners.  
C
92-5/8"  
A
C
F
D
96"  
Nails every 12" (30 cm)  
through Floor Panels into all  
Floor Bond Boards and Floor  
Joists  
D:  
Position the other 48” x 92-5/8”  
D
Floor Panel  
A
flush against  
first panel and flush to edges of  
Floor Frame. Secure panel with  
two 2” nails at outside corners  
and one 2” nail at each of other  
corners.  
24"  
(61 cm)  
24"  
(61 cm)  
A
A
With Floor Panels flush to  
outside edges of Floor Frame,  
nail with 2” nails every 12”  
through Floor Panels into all  
Floor Bond Boards  
&
F
D
.
and Floor Joists  
C
F
D
Note: Mark a line on the Floor Panel  
over the center of each Floor  
Joist @ 24” using a pencil and a  
piece of lumber from the kit (or  
use a chalk line) to make  
nailing easier.  
Your Floor is now complete.  
Check to be sure it is properly  
positioned and leveled to  
ground before beginning  
assembly of your Handy Home  
Wooden Storage Building.  
3
 
Parts needed to cut:  
B
1 - 23-7/8x92-5/8x5/8" Floor Panel  
8X8 OPTIONAL SHELF  
INSTRUCTIONS  
C
E
1 - 2x4x89-1/2" Floor Joist  
2 - 2x4x48" Bond Boards  
- 2" and 3" Nails  
Cut  
Cut  
A
C
B
C
(1) - 89-1/2" Board  
cut down to 88"  
B
(1) - 23-7/8x92-5/8" Panel  
cut down to 23-7/8x89-1/2"  
Cut  
E
E
(2) - 48" Board  
cut down to 2  
pieces of 24-11/16 and 23-3/16"  
SHELF PARTS TO CUT:  
A: Cut the 89-1/2” Board  
down to 88”. Cut both 48”  
C
24-11/16"  
3" Nails  
23-3/16"  
B
23-3/16"  
E
boards  
at 24-11/16”  
leaving 23-3/16”. Finally  
cut the 23-7/8x 92-5/8”  
88"  
32"  
Center  
of Stud  
24-11/16"  
panel  
to 89-1/2”.  
B
28"  
Center  
of Stud  
3" Nails  
SHELF ASSEMBLY:  
B: Mark the 88” Board as shown at 28” then another  
32”. Attach the 23-3/16” with (2) 3” nails as  
shown. Attach the 24-11/16” boards to each end  
of the 88” board with (2) 3” nails.  
Rear Wall  
3" Nails  
3" Nails  
C
SHELF INSTALLATION:  
C: Install the shelf frame resting on the horizonal Back  
3" Nails  
3" Nails  
Wall Brace. Attach middle braces with 3” nails as  
shown. Level front of frame and nail into Side  
Wall Studs or Top Plate depending on your  
building model with 3” nails as shown.  
Rear Wall  
2" Nails  
2" Nails  
D
23-7/8x89-1/2" Panel  
SHELF PANEL INSTALLATION:  
D:  
Center the 23-7/8x89-1/2” panel on the  
shelf frame and attach with 2” nails as  
shown.  
4
 
Parts Needed:  
A
2 - 48x92-5/8x5/8" Floor Panels  
FLOOR KIT INSTRUCTIONS  
FOR 10X8 BUILDINGS  
B
C
D
E
1 - 23-7/8x92-5/8x5/8" Floor Panel  
6 - 2x4x89-1/2" Floor Joist  
2 - 2x4x72" Bond Boards  
2 - 2x4x48" Bond Boards  
- 2" and 3" Nails  
ACTUAL SIZE 120WIDE x 92-5/8” DEEP  
NOTE: Part letters are Not stamped on floor kits. ASSEMBLY OF 10x 92-5/8” FLOOR FRAME  
IMPORTANT!  
If you will be storing heavy items (such as lawn tractor, motorcycle, snowmobile etc.)  
we recommend you upgrade from 24” on center (61 cm) to 12” on center (30.5cm) floor  
framing.This requires you to add the following material:  
• Qty. (5) of 2”x 4”x 89-1/2” (5 x 10 x 227 cm) Treated  
• 20 ea. 3” (7.6cm) galvanized nails  
D
E
NOTE: Part letters are not stamped on floor  
kits.  
A
ASSEMBLY OF 10’ x 92-5/8” FLOOR FRAME  
C
C
C
92-5/8"  
C
A:  
Position Floor Joists  
89-1/2”, Floor  
72”, and Floor Bond  
48” as shown.  
D
Bond Boards  
E
Boards  
Using 3” nails, nail twice through  
E
D
D
E
each Bond Board  
end of each Joist  
&
into each  
C
, keeping pieces  
flush at top and ends, and maintain 24”  
24"  
(61 cm)  
24"  
(61 cm)  
24"  
(61 cm)  
Center of  
Stud  
24"  
(61 cm)  
24"  
(61 cm)  
spacing. Where  
use 4-3” nails.  
D
&
E
join together  
Center of  
Stud  
Center of  
Stud  
Center of  
Stud  
120"  
(305 cm)  
C
E
D
C
D
(4) 3" Nails  
at Joint  
(2) 3" Nails  
B
Y
X
B:  
Completed Floor Frame should be  
positioned at building site, leveled,  
using shims between floor frame and  
ground before proceeding to Floor  
Panel Attachment.  
Square frame by making corner-to-  
corner measurements (X to X and  
Y to Y) the same.  
X
Y
5
 
10X8 FLOOR KIT INSTRUCTIONS  
CONTINUED  
FLOOR PANEL ATTACHMENT:  
C:  
Position a 48 x 92-5/8” Floor  
Panel flush to the outside  
C
A
edges of sides and back of  
Floor Frame. Secure panel with  
two 2” nails at outside corners  
and one 2” nail at other corners.  
92-5/8"  
C
A
D:  
E:  
Position the other 48” x 92-5/8”  
Floor Panel  
A
flush against  
first panel and flush to edges of  
Floor Frame. Secure panel with  
one 2” nail at each of the four  
corners.  
E
D
120"  
Position the 23-7/8” x 92-5/8”  
B
Floor Panel  
flush against  
second panel and flush to  
edges of Floor Frame. Secure  
panel with two 2” nails at  
D
outside corners and one 2” nail  
at each of other corners.  
With Floor Panels flush to  
outside edges of Floor Frame,  
nail with 2” nails every 12”  
through Floor Panels into all  
A
A
E
D
Floor Bond Boards  
&
C
and Floor Joists  
.
Note: Mark a line on the Floor Panel  
over the center of each Floor  
Joist @ 24” using a pencil and a  
piece of lumber from the kit (or  
use a chalk line) to make  
E
D
Nails every 12" (30 cm)  
through Floor Panels into all  
Floor Bond Boards and Joists  
nailing easier.  
Your Floor is now complete.  
Check to be sure it is properly  
positioned and leveled to  
ground before beginning  
E
assembly of your Handy Home  
Wooden Storage Building.  
24"  
(61 cm)  
24"  
(61 cm)  
B
A
A
E
D
6
 
NOTES:  
7
 
NOTES:  
8
 

Graham Field Nebulizer JB0112 164 User Manual
Grizzly Sander G3105 User Manual
HP Hewlett Packard All in One Printer 7500A User Manual
HP Hewlett Packard Laptop 4415S User Manual
HP Hewlett Packard Laptop 4720S User Manual
HP Hewlett Packard Server 643063 001 User Manual
Husky Paint Sprayer HDS420 User Manual
Husqvarna Chainsaw 326C 326L 326LX Series 326LDX Series User Manual
Husqvarna Cordless Saw WS 462 User Manual
Husqvarna Lawn Mower 11 Bio User Manual