Husqvarna Trimmer EA 850 User Manual

GB Operator´s manual  
FR Manuel d'utilisation  
ES Manual de instrucciones  
EDGER ATTACHMENT EA 850  
ACCESSOIRE TRANCHE-BORDURE EA 850  
SUPLEMENTO CORTABORDES EA 850  
Please read these instructions carefully  
and make sure you understand them  
before using the machine.  
Lire attentivement et bien assimiler le  
manuel d’utilisation avant d'utiliser la  
machine.  
Lea detenidamente el manual de  
instrucciones y asegúrese de entender  
su contenido antes de utilizar la máquina.  
GB FR ES  
 
WHAT IS WHAT?  
2
4
3
5
1
10  
4
1
7
6
8
9
What is what on the edger attachment?  
1
2
3
4
5
Cutter  
6
7
8
9
Locking knob  
Drive disc  
Grease filler cap, bevel gear  
Bevel gear  
Support flange  
Locking nut  
Blade guard  
Shaft  
10 Operators manual  
English – 3  
 
SAFETY INSTRUCTIONS  
Cutting equipment  
Machines safety equipment  
This section describes the machines safety equipment, its  
purpose, and how checks and maintenance should be carried  
out to ensure that it operates correctly. See the ”What is  
what?” section to locate where this equipment is positioned  
on your machine.  
The cutter is designed and manufactured to withstand the  
loads that edging of a lawn involves.  
Check the cutting attachment for damage or cracks. A  
damaged cutting attachment should always be replaced.  
The life span of the machine can be reduced and the risk of  
accidents can increase if machine maintenance is not carried  
out correctly and if service and/or repairs are not carried out  
professionally. If you need further information please contact  
your nearest service workshop.  
WARNING! Never use a machine with faulty  
safety equipment.The machine’s safety  
equipment must be checked and maintained  
as described in this section. If your machine  
fails any of these checks contact your  
service agent to get it repaired.  
!
Locking nut  
The locking nut secures the cutting attachment on the output  
shaft.  
WARNING! Always stop the engine before  
you work on any part of the cutting  
equipment.This continues to move even  
after the throttle is released. Check that the  
cutting equipment has stopped completely  
and remove the HT lead from the spark plug  
before you start any work on it.  
!
Protect your hand from injury when assembling, use the blade  
guard as protection when tightening with a socket spanner.  
Cutting attachment guard  
When fitting, tighten the nut in the opposite direction to the  
direction of rotation of the cutting attachment. To remove it,  
undo the nut in the same direction as the cutting attachment  
rotates. (CAUTION! The nut has a left-hand thread.)  
This guard is intended to prevent loose objects from being  
thrown towards the operator. The guard also protects the  
operator from accidental contact with the cutting attachment.  
CAUTION! The nylon lining inside the locking nut must not be  
so worn that you can turn it by hand.The lining should offer a  
resistance of at least 1.5 Nm. The nut should be replaced  
after it has been put on approx. 10 times.  
General safety precautions  
Check that the guard is undamaged and not cracked.  
Replace the guard if it has been exposed to impact or is  
cracked.  
WARNING! The machine can cause serious  
personal injury. Read the safety instructions  
carefully. Learn how to use the machine.  
!
Only use cutting attachments with the guards we  
recommend! See the chapter on Technical data.  
WARNING! A faulty cutting attachment may  
increase the risk of accidents.  
!
CAUTION! Please read the operator’s manual carefully and  
make sure you understand the instructions before using the  
machine.  
4 – English  
 
   
SAFETY INSTRUCTIONS  
Check that the cutter and cutter guard are correctly  
secured.  
Personal protection  
When adjusting the carburettor make sure the cutter is  
held against the ground and that no-one is in the  
immediate vicinity.  
Make sure the cutter always stops when the engine is  
idling.  
Make sure that the handle and safety features are in good  
working order. Never use a machine that lacks a part or  
has been modified outside its specifications.  
Only use the machine for the purpose it was intended for.  
Always wear boots and other equipment described under  
the heading Personal protective equipment.  
Always wear working clothes and heavy-duty long  
trousers.  
General working instructions  
Never wear loose clothing or jewellery.  
IMPORTANT INFORMATION  
Make sure your hair does not hang below shoulder level.  
This section describes the basic safety rules for working  
with edgers.  
Safety instructions regarding the  
surroundings  
If you encounter a situation where you are uncertain how to  
proceed you should ask an expert. Contact your dealer or  
your service workshop.  
Never allow children to use the machine.  
Ensure that no-one comes closer than 15 m while you are  
working.  
Avoid all usage which you consider to be beyond your  
capability.  
Never allow anyone else to use the machine without first  
ensuring that they have understood the contents of the  
operator’s manual.  
Basic safety rules  
Safety instructions before starting work  
1
Look around you:  
To ensure that people, animals or other things cannot  
affect your control of the machine.  
Inspect the working area. Remove all loose objects, such  
as stones, broken glass, nails, steel wire, string, etc. that  
could be thrown out or become wrapped around the cutter  
or cutter guard.  
To ensure that people, animals, etc., do not come into  
contact with the cutting attachment or loose objects that  
are thrown out by the cutting attachment.  
Keep unauthorised persons at a distance. Children,  
animals, onlookers and helpers should be kept outside the  
safety zone of 15 m. Stop the machine immediately if  
anyone approaches.  
CAUTION! Do not use the machine unless you are able to  
call for help in the event of an accident.  
2
3
Do not use the machine in bad weather, such as dense  
fog, heavy rain, strong wind, intense cold, etc.  
Check the entire machine before starting. Replace  
damaged parts. Check that there are no fuel leaks and  
that all guards and covers are complete and fastened  
securely. Check all nuts and screws.  
Make sure you can move and stand safely.Check the area  
around you for possible obstacles (roots, rocks, branches,  
ditches, etc.) in case you have to move suddenly. Take  
great care when working on sloping ground.  
Check that the cutter is not cracked or damaged in any  
other way.  
Make sure the cutter guard is fitted and not damaged.  
4
5
The engine must be switched off before moving.  
Never put the machine down with the engine running  
unless you have it in clear sight.  
English – 5  
 
 
SAFETY INSTRUCTIONS  
Basic working techniques  
WARNING! Sometimes grass or stones can  
get trapped in the cutter guard and cutter.  
Always stop the engine before cleaning.  
!
!
Safety instructions while working  
WARNING! Watch out for thrown objects.  
Always wear approved eye protection. Never  
lean over the cutting attachment guard.  
Stones, rubbish, etc. can be thrown up into  
the eyes causing blindness or serious injury.  
Always ensure you have a safe and stable working  
position.  
Always use both hands to hold the machine. Hold the  
machine at the side of your body.  
Safety instructions after completing work  
Make sure the cutting attachment has stopped before  
cleaning, carrying out repairs or an inspection.  
Disconnect the HT lead from the spark plug.  
Always wear heavy-duty gloves when repairing the cutting  
attachment.This is extremely sharp and can easily cause  
cuts.  
Use your right hand to control the throttle setting.  
Store the machine out of reach of children.  
Use only original spare parts for repairs.  
Make sure that your hands and feet do not come near the  
cutting attachment when the engine is running.  
When the engine is switched off, keep your hands and feet  
away from the cutting attachment until it has stopped  
completely.  
Always carry out edging at full throttle.  
Always keep the cutter close to the ground.  
Always slow the engine to idle speed after each working  
operation. Long periods at full throttle without any load on  
the engine (i.e. without the resistance that the cutting  
attachment exerts on the engine when you are using the  
machine) can lead to serious engine damage.  
Be especially careful when pulling the edger towards you  
during work.  
If any foreign object is hit or if vibrations occur stop the  
machine immediately. Disconnect the HT lead from the  
spark plug. Check that the machine is not damaged.  
Repair any damage.  
6 – English  
 
 
ASSEMBLY  
Fitting the bevel gear  
Fitting the cutter  
Fit the bevel gear on the shaft.Turn the cutter so that the shaft  
engages in the bevel gear.  
Fit the cutter as follows:  
Position the bevel gear so that the slot aligns with the line on  
the shaft.  
1
Fit the drive disc (A) on the output shaft. Make sure that  
the edge that engages in the hole in the cutter is facing  
outwards.  
Firmly tighten the screw.  
2
Prevent the cutter from rotating by inserting the locking pin  
in the hole behind the cutter guard, so that it engages it in  
the corresponding hole in the drive disc.  
3
4
Place the cutter (B) on the drive disc.  
Fit the support flange (C). The support flange must be  
fitted so that its outer edge presses against the cutter.  
5
Fit the locking nut (D). CAUTION! The locking nut has a  
left-hand thread.Tighten the locking nut to a torque of 35-  
50 Nm.  
6
Remove the locking pin.  
CAUTION! Do not forget to remove the locking pin before  
using the machine.  
WARNING! Under no circumstances may the  
edger cutter be used without the cutter  
guard fitted.  
!
English – 7  
 
   
STARTING AND STOPPING  
Starting and stopping  
Check before starting  
For safety reasons follow these recommendations!  
Check that the support flange is not cracked due to fatigue  
or due to being tightened too much. Discard the support  
flange if it is cracked.  
Ensure the locking nut has not lost its captive force. The  
nut lock should have a locking force of at least 1.5 Nm.  
The tightening torque of the locking nut should be 35-50  
Nm.  
Check that the cutter and cutter guard are not damaged or  
cracked. Replace the cutter or cutter guard if they have  
been exposed to impact or if they are cracked.  
Check that the cutting attachment always stops when the  
engine is idling.  
Only use the machine for the purpose it was intended for.  
Make sure that the handle and safety features are in good  
working order. Never use a machine that lacks a part or  
has been modified outside its specifications.  
8 – English  
 
 
MAINTENANCE  
Bevel gear  
Maintenance schedule  
Below you will find some general maintenance instructions. If  
you need further information please contact your service  
workshop.  
The bevel gear is filled with the right quantity of grease at the  
factory. However, before using the machine you should check  
that the bevel gear is filled three-quarters full with grease.Use  
HUSQVARNA special grease.  
Daily maintenance  
1
2
Check that the cutter does not rotate when the engine is  
idling.  
Check that the guard is undamaged and not cracked.  
Replace the guard if it has been exposed to impact or is  
cracked.  
The grease in the bevel gear does not normally need to be  
changed except if repairs are carried out.  
3
4
Check that the cutter is undamaged and not cracked.  
Replace the cutter if necessary.  
Lubricating the flexible drive shaft  
Check that the locking nut is tight.  
Weekly maintenance  
Inside the hollow drive shaft of the edger is a flexible drive  
shaft. This flexible drive shaft should be regularly lubricated  
every 25 hours in operation. Loosen the two screws on the  
bevel gear and remove it. The flexible drive shaft is easily  
removed from the hollow shaft by taking a firm grip on the shaft  
end. Lubricate the entire length of the flexible drive shaft and  
reinsert it in the hollow drive shaft. Turn the shaft while  
inserting it so that it correctly engages in the clutch. Refit the  
bevel gear on the hollow drive shaft and tighten the two screws.  
1
2
Check that the bevel gear is filled three-quarters full with  
lubricant. Fill if necessary using special grease.  
The flexible drive shaft must be lubricated every 25  
working hours or more frequently.  
Technical data  
Technical data  
Weight, Lbs/kg  
1,6  
Adjusting the edger’s cutting depth  
Blade length, mm  
Centre hole, blade, inch/mm  
Speed, blade, rpm  
195  
1 / 25,4  
7140  
The cutting depth must be adjusted before starting work.  
Loosen the locking knob (A) and rotate the guard by  
moving the locking knob forwards or backwards. If the  
locking knob is moved forwards (away from the machine)  
the cutting depth is increased. If the locking handle is  
moved backwards (towards the machine) the cutting  
depth is reduced.  
A
Set the desired cutting depth.  
Lock the locking knob.  
English – 9  
 
         
 
1150309-20  
´®z+R>|¶0z¨  
´®z+R>|¶0z¨  
2006-10-03  
 

Graco Car Seat PD254379A User Manual
Greenheck Fan Smoke Alarm SSFSDR 511 User Manual
Harbor Freight Tools Carbon Monoxide Alarm 92340 User Manual
Harbor Freight Tools Chainsaw Sharpener 93507 User Manual
Harbor Freight Tools Sander 41213 User Manual
Harman Speaker SAT 750 User Manual
HP Hewlett Packard Switch HP 8753C User Manual
Husqvarna Trimmer 80792 User Manual
IBM Conference Phone 8141 User Manual
iLive Music Mixer AP6526 User Manual