INSTALLATION INSTRUCTIONS FOR PART 95-7333
APPLICATIONS
HYUNDAI
Sonata 2009-10
95-7333
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted To Match Factory
Bronze Dash
KIT COMPONENTS
A) Double DIN Trim Plate B) Double DIN Brackets
Wiring & Antenna Connections (sold separately)
• 70-7303 - Hyundai / Kia Harness 2009
• 40-KI11 - Kia Antenna Adapter 2007-up
A
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver • Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
95-7333 DASH DISASSEMBLY
HYUNDAI SONATA 2009-10
A
1
2
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
Remove shifter knob from stem.
(Figure A)
3
Unclip and remove the shifter trim
panel. (Figure B)
Unclip and remove the (2) side trim
panels from the center console area.
(Figure C)
4
B
Continued on page 2.
C
1
95-7333 DASH DISASSEMBLY
HYUNDAI SONATA 2009-10
D
5
Remove (2) Phillips screws then
unclip and remove the small trim
panel below the factory climate con-
trols and above the pocket.
(Figure D,E)
6
7
Unclip and remove the trim panel sur-
rounding the radio and including the
climate controls and vents. (Figure F)
Remove (4) Phillips screws securing
the radio. Unplug and remove the
radio. (Figure G)
E
Continue to kit assembly.
F
G
2
95-7333 KIT ASSEMBLY
DOUBLE DIN/STACKED ISO MOUNT
UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
A
Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate. (Figure A)
1
2
Slide the Double DIN or stacked ISO
mount unit(s) into the bracket/trim
plate assembly and secure the
unit(s) to the assembly using the
screws supplied with the unit(s).
(Figure B)
Continue to final assembly.
B
3
95-7333 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
95-7333
NOTES
5
95-7333 INSTRUCTIONS
1-800-221-0932
REV. 04/30/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST95-7333
|