IBM Computer Monitor T86A User Manual

These user’s setup instructions cover typical user environments. The on-

screen messages may differ depending on the level of your hardware and

software. In some cases you may need to vary the setup procedures.

For more information, refer to your computer or operating system manuals or

consult your system administrator or dealer.

Ces instructions de configuration s’appliquent aux environnements

d’utilisation typiques. Les messages affichés à l’écran peuvent varier en

fonction de votre configuration matérielle et logicielle. Dans certains cas, il

peut être nécessaire de changer les procédures de configuration.

Pour de plus amples informations, veuillez consulter les manuels de votre

ordinateur et de votre système d’exploitation, ou consultez l’administrateur de

votre système ou votre revendeur.

Diese Anweisungen zur Installation durch den Benutzer gelten für typische

Betriebsumgebungen. Die Bildschirmmeldungen können je nach Art der

verwendeten Hardware und Software auch anders lauten. In einigen Fällen

müssen die Einstellungsschritte unter Umständen abgeändert werden.

Weitere Informationen finden Sie im Computer-order Betriebs-

systemhandbuch, oder wenden Sie sich an lhren System-administrator oder

Fachhändler.

Estas instrucciones sobre la configuración abarcan típicos entornos de

usuario. Los mensajes en pantalla pueden diferir según el nivel de su

hardware y software. En algunos casos, puede que sea necesario variar los

procedimientos de configuración.

Para mayor información, consulte los manuales de su ordenador o sistema

perativo, o consulte a su administrador de sistema o proveedor.

Queste istruzioni utente per il setup coprono ambienti utente tipici. I

messaggi su - schermo possono variare a seconda del livello del proprio

hardware e software. In alcuni casi puo’ essere necessario modificare le

procedure di setup.

Per maggiori informazioni, fare riferimento ai manuali del proprio computer o

del sistema operativo, oppure consultare il proprio amministratore di sistema

o il proprio rivenditore.

これらのユーザーズセットアップガイドでは、一般的なユーザー環境につ

いてサポートしています。画面上のメッセージは使用されているハードウ

ェアのレベルやソフトウェアの種類によって異なる場合があります。また、

場合によっては、セットアップ手順の変更が必要な場合もあります。

詳細につきましては、現在使用中のコンピュータに付属のコンピューター

マニュアルかオペレーションマニュアルを参照するか、システム管理者か

GEVAAR

Ga als volgt te werk om het gevaar van een elektrische schok te voorkomen:

Verwijder in geen enkel geval de kap.

Stel dit produkt alleen in werking als de voet is bevestigd.

Sluit dit apparaat niet aan op, of verbreek de aansluiting van dit apparaat niet

van een contactdoos tijdens onweer.

Het netsnoer moet worden aangesloten op een geaarde contactdoos met

correcte bedrading.

Ook alle apparatuur waarop dit produkt wordt aangesloten moet zijn

aangesloten op een contactdoos met correcte bedrading.

Om het beeldscherm te ontkoppelen van de netvoeding, dient u de stekker uit

de contactdoos te trekken. De contactdoos dient goed toegankelijk te zijn.

PELIGRO

Para evitar riesgos de descargas eléctricas:

No retire bajo ningún concepto las cubiertas.

No maneje el monitor sin antes acoplar el soporte.

No conecte ni desconecte el equipo de una toma de alimentación durante

una tormenta eléctrica.

El cable de alimentación debe estar conectado a un enchufe debidamente

cableado y con toma de tierra.

Cualquier equipo al que se vaya a conectar este producto también debe estar

conectado a tomas de alimentación cableadas y conectadas a tierra

correctamente.

Para aislar el monitor del suministro eléctrico, debe retirar el enchufe de la

toma de alimentación. Esta toma deberá ser de fácil acceso.

PERICOLO

Per evitare il rischio di scariche elettriche:

Non rimuovere nessuna parte del telaio.

Non accendere il prodotto se il piedistallo non è stato montato.

Non collegare o scollegare il prodotto nel corso di un temporale.

La spina del cavo di alimentazione deve essere collegata ad una presa di

corrente con messa a terra, installata in maniera appropriata.

Le apparecchiature a cui il prodotto viene attaccato devono essere collegate

a prese di corrente con messa a terra, installate in maniera appropriata.

Per isolare il monitor dalla corrente elettrica, staccare la spina dalla presa di

alimentazione, che deve essere facilmente accessibile.

PERIGO

Para evitar o perigo de choques eléctricos:

Não retire as coberturas.

III

Não utilize este produto antes de montar a base.

Não ligue nem desligue este produto durante uma tempestade eléctrica.

O cabo de alimentação deve ser ligado a uma tomada eléctrica devidamente

ligada à terra.

Qualquer equipamento ligado a este produto deve estar ligado a tomadas

eléctricas devidamente ligadas à terra.

Para isolar o monitor da fonte de alimentação, retire a ficha do cabo de

alimentação da tomada eléctrica. A tomada eléctrica deve ser de fácil acesso.

FARE

Sådan undgår du elektrisk stød:

Kabinettet må under ingen omstændigheder fjernes.

Undgå at anvende dette produkt, uden at vippe/drejefoden er monteret.

Undgå at tilslutte eller frakoble dette produkt i tordenvejr.

Netledningen skal være tilsluttet en korrekt jordet stikkontakt med korrekt

ledningsføring.

Alt udstyr, som tilsluttes dette produkt, skal også være tilsluttet korrekt

jordede stikkontakter med korrekt ledningsføring.

For at isolere skærmen fra strømforsyningen, skal stikket tages ud af

stikkontakten. Stikkontakten bør være let tilgængelig.

FARE

Slik unngår du fare for elektrisk støt:

Ikke ta av dekslene.

Ikke bruk produktet dersom sokkelen ikke er montert.

Ikke koble produktet til eller fra under tordenvær.

Pluggen på strømledningen må kobles til korrekt montert og jordet

strømuttak.

Utstyr som dette produktet eventuelt blir koblet til, må også kobles til korrekt

montert og jordet strømuttak.

For å isolere skjermen fra strømkilden må du ta ut pluggen fra strømuttaket.

Strømuttaket bør være lett tilgjengelig.

Varning - livsfara

För att undvika risk för elektriska stötar måste du tänka på följande:

Ta inte bort några skyddskåpor.

Använd inte den här produkten innan du har satt fast stativet.

Anslut inte produkten till ett eluttag under åskväder. Koppla inte heller ur

produkten från ett eluttag under åskväder.

Strömkabeln måste anslutas till ett felfritt och jordat uttag.

All utrustning som den här produkten kopplas till måste också anslutas till

felfria och jordade uttag.

För att bryta strömmen till bildskärmen måste du dra ut kontakten.

Vägguttaget bör vara lätt att komma åt.

VAARA

Sähköiskun vaaran välttämiseksi:

Älä avaa laitteen kansia missään tilanteessa.

Älä käytä laitetta, ellei jalustaa ole kiinnitetty.

Älä kytke laitetta pistorasiaan tai irrota sitä pistorasiasta ukonilman aikana.

Virtajohto on kytkettävä asianmukaisesti johdotettuun ja maadoitettuun

pistorasiaan.

Kaikki muutkin laitteet, joihin tämä tuote on liitetty, on kytkettävä

asianmukaisesti johdotettuihin pistorasioihin.

Kun haluat erottaa näyttimen sähköverkosta, sinun pitää irrottaa sen

verkkojohto pistorasiasta. Pistorasian pitäisi olla mahdollisimman lähellä

näytintä ja vaivattomasti käsillä.

ΚΙΝΔΥΝΟΣ

Για να αποφύγετε τον κίνδυνο από χτυπήματα:

Μην αφαιρείτε τα καλύμματα.

Μη θέτετε το προϊόν αυτό σε λειτουργία εκτός εάν είναι τοποθετημένο στη

βάση του.

Μη συνδέετε ή αποσυνδέετε το προϊόν αυτό κατά τη διάρκεια ηλεκτρικής

καταιγίδας.

ηλεκτροδέκτης του καλωδίου πρέπει να συνδέεται σε κανονικά

καλωδιωμένο και γειωμένο ηλεκτροδότη.

Οποιαδήποτε συσκευή με την οποία θα συνδεθεί το προϊόν αυτό πρέπει

επίσης να συνδέεται σε κανονικά καλωδιωμένους και γειωμένους

ηλεκτροδότες.

Για να μονώσετε τον ενδείκτη από την ηλεκτρική παροχή, πρέπει να

αφαιρέσετε τον ηλεκτροδέκτη από την έξοδο ηλεκτρικού ρεύματος. Η έξοδος

ηλεκτρικού ρεύματος πρέπει να είναι εύκολα προσβάσιμη.

Tehlike !

Þok tehlikesini önlemek için :

Kapaklarýn yerini deðiþtirmeyin.

Eðer destek baðlý deðilse, bu üretimi çalýþtýrmayýn.

Elektrik cereyaný açýk olduðu zaman bu üretimi baðlamayýn veya kesmeyin.

Kablo fiþi elektrik þebekesi ile çok iyi baðlanmýþ olmalýdýr ve tam tesisat

borusuna baðlanmalýdýr.

Hangi tesisat veya hangi üretim olursa olsun, tam elektrik þebekesine iyi bir

þekilde baðlanmalýdýr ve tam tesisat borusuna takýlmalýdýr.

Elektrik cereyaný ekranýný tam izole etmek için, kablo fiþini elektrik

borusundan çýkarýnýz. Elektrik borusu giriþe kolaylýkla açýk olmalýdýr.

危険

安全にお使いいただくためには、以下について実行してください。

カバーを外さないこと。

スタンドを装着していない時は、本体を作動させないこと。

落雷の最中に本体を接続したり切断したりしないこと。

電気コードプラグを正確に接地されたプラグの差込口に挿入すること。

又、本体付属の部品についても、きちんと接地されたプラグの差込口に挿

入すること。

電源からモニタを絶縁させたい場合には、プラグをコンセント差込口から

抜いてください。

IBM T86A

LCD Color Monitor

User’s Manual

First Edition (January 2000)

This publication could contain technical inaccuracies or typographical errors.

Known inaccuracies and errors may be corrected in later editions. IBM may

make improvements and/or changes in the product(s) and/or program(s) at

any time.

It is possible that this publication may contain reference to, or information

about, IBM products (machines and programs), programming, or services

that are not announced in your county.

Requests for copies of this publication and for technical information about

IBM products should be made to your IBM Authorized Dealer or IBM Retailer.

No part of this publication may be reproduced or distributed in any form or by

any means without prior permission in writing from the International Business

Machines Corporation.

RIGHTS RESERVED.

Notices:

References in this publication to IBM products, programs, or services do not

imply that IBM intends to make these available in countries in which IBM

operates. Any reference to an IBM product, program or service is not intended

to state or imply that only IBM’s product, program, or service may be used.

Any functionally equivalent product, program, or service that does not infringe

IBM‘s intellectual property rights or other legally protectable rights may be

used instead of the IBM product, program, or service. Evaluation and

verification of operation in conjunction with other products, programs, or

services, except those expressly designated by IBM, are the user’s

responsibility.

IBM may have patents or pending patent applications covering subject matter

in this document. The furnishing of this document does not give you any

license to these patents.

Trademarks

The following terms, used in this publication, are trademarks or service marks

of the IBM Corporation in the United States or other countries:

IBM

IBM HelpCenter

iii

TABLE OF CONTENTS

Setup...............................................................................................................1

Unpacking........................................................................................................1

Hardware Requirements .................................................................................1

Workplace Preparation....................................................................................1

Working Practices............................................................................................2

Adjusting the Monitor Position.........................................................................3

Removing the Locking Pin and Lifting the Monitor..........................................4

Removing the Stand from the monitor.............................................................5

Add Another Signal Cable...............................................................................7

Caring for your Monitor....................................................................................8

Maintenance....................................................................................................9

Installing the Monitor..................................................................................10

Installing the Monitor .....................................................................................10

Configuring Your Monitor...........................................................................12

Automatic Setup ............................................................................................12

SETUP Diskette for Windows 95 or Windows 98 or Windows 2000.............12

Auto Setup for Windows 3.1, Windows 95, Windows 98 or Windows 2000 or

Windows NT ..................................................................................................13

Adjusting the Monitor .................................................................................15

User Controls.................................................................................................15

CONTROLS LOCK / UNLOCK......................................................................16

On-screen display (OSD) controls.................................................................17

Further Information .....................................................................................22

Supported Timing Modes ..............................................................................22

Power Management ......................................................................................24

Product Disposal ...........................................................................................24

Troubleshooting..........................................................................................25

Specification ................................................................................................27

Warranty Statements ..................................................................................28

Compliance ..................................................................................................43

Statement ......................................................................................................43

Power Cord....................................................................................................44

Industry Canada Compliance Statement ......................................................44

Déclaration de Conformité Industrielle du Canada .......................................44

TCO’95 applies to 9497-AG1 ......................................................................45

TCO’99 applies to 9497-AW1......................................................................45

Hinweise........................................................................................................47

Setup

Unpacking

Check following items. If they are missing or damaged, consult your place of

purchase immediately.

LCD monitor

DVI-Analogue signal cable

Power Adapter

Power Cord

User Guide

Installation Diskette

Hardware Requirements

This monitor requires a computer with a suitable on-board sub-system or

Video Adapter card that can support SXGA 1280x1024, XGA 1024x768,

SVGA 800x600, or VGA 640x480 at 60Hz.

Note: Recommended operating mode is 1280 x 1024 @ 60 Hz.

Workplace Preparation

Height

The monitor should be positioned so that the top of the screen is slightly

below your eye level when sitting at your workstation.

Orientation

Choose a position that gives the least reflection from lights and windows,

usually at a right angle to any windows.

The monitor should be positioned directly in front of you so that you do

not have to twist your body to use it.

Tilt the monitor to a comfortable viewing angle.

Working Practices

Rest

Take regular breaks. Vary your posture, stand up and stretch occasionally, as

prolonged use of computer workstations can be tiring.

Back

You should sit back in your chair and use the backrest.

Hands

Use a light touch on the keyboard, keeping your hands and fingers relaxed.

Allow a space in front of the keyboard to rest your wrists when not typing.

Consider using a wrist pad.

Eyesight

Working with monitors, in common with any prolonged close work, can be

visually demanding. Look away from the screen periodically and have your

eyesight checked regularly.

Screen settings

Set the screen brightness and contrast to a comfortable level. You may have

to adjust this as the lighting changes during the day. Many application

programs let you select color combinations, which can help you to view in

comfort. See the Adjusting the Monitor section for more information.

Adjusting the Monitor Position

Rotation

The monitor can be put in portrait or landscape mode as shown below.

Note: The rotate mechanism will not operate when the monitor is in the lowest

position.

ꢀ

Step 1

Step 2

Step 3

You can tilt the screen backward and forward –tilt 1-29 degrees as shown

below.

ꢀ

You can adjust the screen height by a maximum of 130mm.

ꢀ

You can swivel the base around – swivel 300 degrees..

ꢀ

Removing the Locking Pin and Lifting the Monitor

The monitor has a locking pin to stop the screen from moving in transit. Before

the height adjustment can be used, you must remove the locking pin from the

stand.

1. With the rear of the monitor facing you, locate the locking pin as show in

diagram

2. Turn the locking pin a quarter of a turn and remove

3. The monitor height can now be adjusted

Removing the Stand from the monitor

1. Lay the monitor face down on a flat surface

(NOTE: It is important to place a soft cloth or other protective material

beneath the monitor to avoid scratching the screen.)

2. Push up the cable cover and remove it

3. Remove the four mounting screws on the monitor.

Caution: The stand is heavy and care should be taken to avoid dropping it.

4. Separate the cables from the Stand

5. Remove the stand from the monitor

Add Another Signal Cable

1. Remove the stand from the monitor as shown above.

2. Remove the plate.

3. Attach the other cable.

4. Attach the plate.

5. Insert the power cable and signal cables into the hole of the stand.

6. Attach the 4 screws.

7. Push down the cable cover and fasten it.

Caring for your Monitor

Be sure to turn off the power before you perform any maintenance on the

monitor. Clean your monitor as follows:

Gently wipe the covers and the screen with a soft cloth.

Remove finger marks and grease with a damp cloth and mild detergent;

do not use solvents or abrasives.

Never apply detergent or other liquid directly to the screen. Dampen the

cloth and then wipe.

Never use flammable cleaning material to clean your IBM monitor or any

other electrical apparatus.

Maintenance

ꢀꢀ

ꢀꢁ Do not expose the monitor to direct sunlight or heat.

ꢂꢁ Do not spill liquid on the monitor.

ꢃꢁ Do not attempt to open the monitor. For service, see the

Troubleshooting section.

ꢄꢁ Do not place anything on your monitor. Poor ventilation will elevate

the temperature in the monitor.

ꢅ

Installing the Monitor

This monitor is equipped with an auto-sensing power supply for voltage range

100V ac to 240V ac at 50Hz or 60Hz.

Be sure to read the “ Safety instructions” at the front of this User’s

Guide before carrying out this procedure.

1. Make sure that the computer power is turned off.

2. Plug the video signal cable into the video signal connector of your

computer.

3. Plug the power cord into the monitor.

4. Connect the other end of power cord to a properly grounded electrical

outlet.

5. Switch on the computer and the monitor.

Configuring

_{Your Monitor}3

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

Automatic Setup

When you first use your monitor you must perform Automatic Setup (AUTO

SETUP). This procedure sets up your monitor to process the video signals

from your computer without image discoloration or smearing. After you

perform AUTO SETUP, the settings are stored and used each time you turn

on the monitor.

The Setup Utility included on the setup diskette is for displaying a test pattern.

It does not replace or modify the display driver. The Automatic Setup

instructions require the monitor to be warmed up for 15 minutes. This is not

required for normal operation.

SETUP Diskette for Windows 95 or Windows 98 or

Windows 2000

To use the Plug and Play feature in Windows 95 or Windows 98 or Windows

2000, files should be loaded from the IBM FLAT PANEL Monitor Installation

diskette as follows:

1. Turn off the computer and all attached devices.

2. Ensure that the monitor is connected correctly.

3. Turn on the monitor and then the system unit. Allow the system to boot

into Windows 95 or Windows 98 or Windows 2000.

4. Your computer’s Plug and Play code may warn you that your system

hardware has changed. This probably means that it has detected your

new monitor for the first time.

5. Open the DISPLAY PROPERTIES windows by clicking on START,

SETTINGS, CONTROL PANEL and then double clicking on the

DISPLAY icon.

6. Select the SETTINGS tab.

7. Select the CHANGE DISPLAY TYPE button.

8. Select the CHANGE MONITOR TYPE button. Insert the Setup diskette

into drive A: and select the HAVE DISK button.

9. Choose the 9497 monitor and select OK>, the files will be copied from

the diskette to your hard drive.

10. Close all open windows and remove the diskette.

11. Reboot the system. The system will automatically select the maximum

refresh rate and corresponding Color Matching Profile.

Auto Setup for Windows 3.1, Windows 95, Windows

98 or Windows 2000 or Windows NT

1. Turn on the monitor first; then the computer.

If the message NO SIGNAL is displayed, or if nothing is displayed check:

The video interface cable is connected properly.

The correct video adapter card is installed.

Video card is set for a mode within the operating range of your new

monitor.

2. Wait approximately 15 minutes, until the monitor warms up.

3. Insert the “Flat Panel Monitor Installation Diskette” into the diskette drive.

4. Check the operating system installed on your computer and follow the

instructions from the table below.

When test pattern appears, press the OSD (On Screen Display) entry key (

and then use the left and right arrow key to highlight the image set-up icon

)

(

). Press enter key to enter sub-menu and then press enter key again to

activate the auto setup procedure. Image Setup will auto-adjust H-position,

V-position, Pixel Clock and Phase.

Note : Direct access to the auto setup function is also provided by

simultaneously pressing the left and right arrow keys.

ꢁꢂ ꢃꢄꢅꢆꢀꢇ ꢆ ꢈꢄꢅꢉꢊꢀꢋꢄꢅꢀꢌꢍ ꢆꢀꢎꢏꢐꢀꢌꢅꢆꢑꢀꢒ ꢓꢓꢀꢔꢅꢀꢉ ꢈꢕꢓꢍꢖꢅꢉꢂ

ꢗꢂ ꢘꢙꢅꢈꢈꢀꢍꢆꢖꢀꢚꢛꢌꢕꢑꢋꢅꢙꢀꢜꢅꢖꢔꢛꢍꢙꢉꢀꢜꢅꢖꢀꢋꢛꢀꢅꢝ ꢋꢀꢋꢄꢅꢀꢋꢅꢈꢋꢀꢕꢍꢋꢋꢅꢙꢆꢂ

Operating

System

Step1

Step2

Step3

Step4

Windows 3.1

Windows NT 3.5

Windows 95

Open

PROGRAM

MANGER

Select Select RUN Type

“A:\TESTPAT”

and press

FILE

Select RUN

ENTER

Select START

Windows 98

Windows 2000

Windows NT 4.0

You have completed the monitor setup for Windows operating system.

Adjusting the Monitor

User Controls

User controls features

Icon Direct Access Function

Function Using OSD Menu

Controls

1. Exits from menus, sub

menus

Selects video input 1or 2

2. Exits from OSD

1. Brings up Brightness control

OSD

2. Left and Right arrows pressed

together bring up auto setup

OSD

Moves the cursor to highlight

icons or make adjustments

1. Brings up Contrast control

OSD

2. Left and Right arrows pressed

together bring up auto setup

OSD

Moves the cursor to highlight

icons or make adjustments

Control lock activated when

pressed for 10 seconds

Controls unlocked if held for 10

seconds.

1. Displays main OSD menu

2. Enters highlighted menus

and submenus

3. Selects highlighted option

Switches the monitor on or off

ꢀꢀꢀ

The image is already optimized for many display modes, however the user

controls can be used to adjust the image to your liking.

ꢀ

ꢀꢀ

^ꢀꢀThe settings are saved after adjustment and when exiting the OSD, and will

be effective thereafter

ꢀ

CONTROLS LOCK / UNLOCK

This feature allows you to secure the current control settings, so that they

cannot be inadvertently changed. Note: This does not include brightness and

contrast.

Push and hold the enter button [

Locked” appears.

] for 10 seconds; the message “Controls

You can unlock the OSD controls at any time by pushing the enter button [

]

for 10 seconds; the message “Controls Unlocked” will appear.

On-screen display (OSD) controls

ꢆꢇ ꢅꢈ ꢉꢉꢊꢋꢌꢈꢅꢍꢇꢊꢎꢇꢅꢏꢐ ꢅꢏꢑꢒꢓꢈꢉꢏꢔꢕ ꢅꢍꢊꢉꢇꢅꢉꢇ ꢅꢓꢈ ꢐ

ꢎꢖꢋꢉꢐꢖꢕꢈꢅꢏꢐ ꢅꢏꢎꢎ ꢈꢈ ꢑꢅꢉꢇꢐꢖꢓꢌꢇꢅꢉꢇ ꢅꢗꢋꢘꢈꢎꢐ

ꢀThe LCD monitor takes up to 15

minutes to become thermally

stable after each time you switch

ꢋ

ꢙꢊꢈꢚꢕꢏꢛꢅꢜꢗꢝꢙ ꢁꢅ!ꢐ ꢈꢈꢅꢉꢇ ꢅ ꢋꢉ ꢐꢅꢔꢓꢉꢉꢖꢋꢅ"

ꢑꢊꢈꢚꢕꢏꢛꢅꢉꢇ ꢅ$ꢏꢊꢋꢅꢗꢝꢙꢅ$ ꢋꢓꢁ

#ꢅꢉꢖ

it on. To make accurate adjustments,

wait until the monitor has warmed up.

ꢁꢂꢃꢄꢃꢅꢆꢀꢅꢇꢇ ꢅꢈꢅꢂꢉ ꢀꢊꢋꢀꢌꢍꢎ

ꢀꢁꢂꢃꢄꢀꢅꢃꢆ

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

MAIN MENU

H-POSITION

ꢇꢆ ꢄꢀꢅꢃꢆ

BRIGHTNESS

Control and

Adjustment

OSD Icon

BRIGHTNESS

CONTRAST

Description

Sub-menu(s)

Adjusts Brightness

Adjusts Contrast

The IMAGE SET-UP

function is used to

compensate for noise in

the video signals, which

causes horizontal lines or

areas on the screen

where the image appears

to be unstable and jitters

or shimmers. This can be

done automatically or

manually.

AUTO

the

selected

Auto

image will be

automatically

adjusted.

IMAGE SET-UP

This allows you to

remove

horizontal

and

any

noise

clear

sharpen

appearance

characters.

Fine adjustments

should be made

the

If manual is selected, the

user will go to the manual z Fine

adjustment screen. Coarse

Manual

after

making

Coarse

adjustments.

Control and

Adjustment

OSD Icon

Description

sub-menu(s)

COLOR MODE

Preset 1

(Warm White)

Preset 2

(Normal White)

Preset 3

(Cool white)

Select the Preset Color

Mode you find most

comfortable.

Use the User Color Mode

menu, if necessary, to

define your own color

preference.

USER COLOR

MODE

COLOR

Increases or

decreases

redness

Red

Green

Blue

Increases or

decreases

greenness

Increases or

decreases

blueness

H-POSITION

V-POSITION

Changes the position of

the OSD on the screen.

OSD Position

Reset

returns

all

available functions (apart

from language, which will

YES

not

adjusted

change

via

unless

the

RESET

LANGUAGE menu,) to

their factory presets.

Control and

Adjustment

OSD Icon

Description

sub-menu(s)

Selects video input 1 or

Input 1 input 2

video input 2

Input Selection

Moves the displayed

image left or right.

H-POSITION

V-POSITION

Moves the displayed

image up or down.

NORMAL-original

Displays the image in its original size or image size.

expanded size to fill the full screen of your EXPANDED-

IMAGE SIZE

monitor.

image expanded

to fill the screen.

ENGLISH

FRANCAIS

DEUTSCH

ITALIANO

ESPANOL

JAPANESE

The language chosen affects only the

language used for the OSD.

It has no effect on any software running on

the computer.

Language

OSD time

Selects the OSD display duration time.

( Between 5 and 60 seconds)

Adjust to your

preference.

The model name, serial number, year of

manufacture and current display mode

are included in the information screen.

Informs the user of the current display

mode, and also shows the preset and user

modes stored in the monitor. The current

display mode is shown at the base of the

preset mode and user mode displays.

Use the left and right buttons to see the

preset modes and user modes screens.

PRESET

Information

USER MODE

Further Information

Supported Timing Modes

The Display mode the monitor uses is controlled by the computer. Therefore,

you should refer to you computer documentation for details on how to change

display modes.

For the display modes listed below, the screen image has been optimized

during manufacture.

ꢀ

Input display mode

Multi-scan

operation

Actual

Address

ability

Horizontal

Vertical

Dot Clock

Remark

Frequency Frequency Frequency

display

(KHz)

(Hz)

(MHz)

25.17

28.32

25.18

30.24

31.5

resolution

*640x350

*720x400

*640x480

*800x600

832X624

31.47(P)

31.47(N)

35.00(N)

37.86(N)

37.50(N)

37.88(P)

48.08(P)

46.86(P)

49.72(N)

70.08(N)

70.08(P)

60.00(N)

67.00(N)

72.80(N)

75.00(N)

60.32(P)

72.19(P)

75.00(P)

74.55(N)

60.00(N)

70.10(N)

75.00(P)

74.93(N)

75.00(P)

75.06(N)

66.00(P)

60.00(P)

71.53(N)

75.00(P)

76.16(N)

DOS

Macintosh

VESA

Macintosh

VESA

full screen

1280x1024

31.5

40.00

50.00

49.50

57.29

65.00

75.00

78.75

80.00

108.00

100.00

94.50

108.00

128.00

135.00

135.09

*1024x768 48.36(N)

1024x768 56.48(N)

*1024x768 60.02(P)

1024X768 60.24(N)

Macintosh

VESA

1152x864

1152x870

1152x900

67.50(P)

68.68(N)

61.84(P)

*1280x1024 64.00(P)

*1280x1024 75.83(N)

*1280x1024 80.00(P)

1280x1024 81.18(N)

VESA

Notes (1) The timing with “*” symbol are adjusted in the factory.

(2) (P), (N) stands for “Positive”, “Negative” polarity of incoming

timing.

Power Management

To benefit from power management, the monitor must be used in conjunction

with a computer that implements the Video Electronics Standards Association

(VESA) Display Power Management Signaling (DPMS) Standard.

The power management feature is invoked when the computer recognizes

that you have not used your mouse or keyboard for a user-definable period.

There are several states as described in the table below.

IBM recommends that you switch off your monitor at the end of each working

day, or whenever you expect to leave it unused for long periods during the day.

State

Power

Indicator

Screen

Restoring

Operation

Steady green

Steady amber

Normal

Blank

DPMS Standby

Press a key or

move the mouse.

DPMS Suspend

DPMS Off

Flashing amber

Blank

Press a key or

move the mouse.

Press a key or

move the mouse.

Your flat panel monitor consumes less than 3W when in the DPMS “standby”,

“suspend” or “off ” state.

Product Disposal

The fluorescent lamp in the liquid crystal display contains mercury. Dispose of

it as required by local ordinances and regulations.

Troubleshooting

If you encounter trouble with this product, first check that the monitor is

properly installed.

Can't find the 9497 Monitor on the Windows 95® or

Windows 98® or Windows 2000® monitor lists.

You need to update the Windows 95® or Windows 98® or Windows 2000®

setup information for your 9497 Monitor.

There is no picture on the screen.

Check:

Power saving mode. Press any key or move the mouse to deactivate the

mode.

Signal cable connector pins. If there are bent or missing pins, consult your

place of purchase.

That the video mode selected is within the operating range of the monitor. If

the power indicator on the monitor bezel is green and flashing then the

monitor has detected signals that are outside its operating range.

The picture is unstable.

Check:

Signal cable connector pins. If there are bent or missing pins, consult your

place of purchase.

Graphics card. Ensure a valid mode is selected.

Characters look too dark or too light.

Adjust Contrast or Brightness

The image has a few tiny dots that are not the same color as

the surrounding area.

The Liquid Crystal Display (LCD) contains about 3 million Thin Film

Transistors (TFTs). A small number of missing, discolored, or lighted dots

may be present on the screen. This is an intrinsic characteristic of TFT LCD

technology and is not an LCD defect.

Need More Help?

If your problems remain after checking this manual, please contact your

reseller or call your IBM Help Center.

In the US call 1-800-772-2227

In Canada call 1-800-565-3344

^{Specification}7

LCD Panel 18.1", TFT

Dimensions (W x H x D)

Width

Depth

Height

418mm (W)

260mm (H)

400-530mm (D)

Weight (net)

Stand Range

10.5 Kg

Vertical (Tilt)

Vertical (Lift)

Swivel

Range: 1-29 degrees

Range: 130mm

Range: 300 degrees

Range: 90 degrees

Rotate

Power Supply (Universal)

Input voltage

100 ~ 240VAC at

50 ~ 60Hz

Power consumption 65W max.

Max. Addressability

Video Input

1280 x 1024 (SXGA)

RGB input

User controls

Power ON/OFF, OSD

Regulatory Compliance

UL, CSA, FCC, TÜV/GS,

VCCI, CE, D.N.S.F.,

SASO, CCIB/CCE,

TÜV/Ergo, SISIR, MEEI,

PCBC, EZU, SIQ, NOM,

GOST, C-Tick, BCIQ,

TCO95 (9497-AG1),

TCO99 (9497-AW1),

MPRIII, NUTEK, SQTSB

Display Area

359mm(H) x 287.2mm(V)

Ambient Temperature

Operating

Shipping

Storage

+ 5ºC ~ +35ºC

-20ºC ~ +60ºC

Humidity

Operating

Shipping

Storage

10% ~ 80%

5% ~ 95%

Warranty Statements

The warranty statements consist of two parts: Part 1 varies by country. Part2

is the same for both statements. Be sure to read both the Part 1 that applies

to your country and Part 2.

Worldwide except Canada, Puerto Rico, Turkey and United States

(Z125-5697-01 11/97)

(Part 1 - General Terms)

Worldwide Country-Unique Terms

(Part 2 – Country Unique Terms)

United States, Puerto Rico, and Canada (Z125-4753-05 11/97)

(Part 1 - General Terms)

Translations of IBM's warranty statements also can be found on the

Installation Diskette. Your Installation Diskette includes translations of IBM's

Statement of Warranty in the following languages:

Worldwide Statement of Warranty (Except Turkey, U.S. ,Puerto Rico and

Canada):

Arabic

Z1255697-ara.htm

Z1255697-bra.htm

Z1255697-bul.htm

Z1255697-chi.htm

Z1255697-cor.htm

Z1255697-cze.htm

Z1255697-dan.htm

Z1255697-dut.htm

Z1255697-eng.htm

Z1255697-fin.htm

Z1255697-fre.htm

Z1255697-ger.htm

Z1255697-gre.htm

Z1255697-heb.htm

Z1255697-hun.htm

Z1255697-ita.htm

Brazilian Portuguese

Bulgarian

Chinese

Croatian

Czech

Danish

Dutch

English

Finnish

French

German

Greek

Hebrew

Hungarian

Italian

Japanese

Korean

Norwegian

Polish

Portuguese

Russian

Slovakian

Slovenian

Spanish

Z1255697-jap.htm

Z1255697-kor.htm

Z1255697-nor.htm

Z1255697-pol.htm

Z1255697-por.htm

Z1255697-rus.htm

Z1255697-sla.htm

Z1255697-sle.htm

Z1255697-spa.htm

Z1255697-swe.htm

Z1255697-tai.htm

Swedish

Taiwanese

Turkey Statement of Warranty

Turkish

Z1255698-tur.htm

Z1255698-eng.htm

English

United States, Puerto Rico and Canada Statement of Limited Warranty

English

French Canadian

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

Z1254753-eng.htm

Z1254753-fca.htm

IBM Statement of Warranty World-wide except Canada, Puerto Rico,

Turkey, United States (Part 1 - General Terms)

This Statement of Warranty includes Part 1 - General Terms and Part 2 -

Country-unique Terms. The terms of Part 2 may replace or modify those

of Part 1. The warranties provided by IBM in this Statement of Warranty apply

only to Machines you purchase for your use, and not for resale, from IBM or

your reseller. The term "Machine" means an IBM machine, its features,

conversions, upgrades, elements, or accessories, or any combination of them.

The term "Machine" does not include any software programs, whether pre-

loaded with the Machine, installed subsequently or otherwise. Unless IBM

specifies otherwise, the following warranties apply only in the country where

you acquire the Machine. Nothing in this Statement of Warranty affects any

statutory rights of consumers that cannot be waived or limited by contract. If

you have any questions, contact IBM or your reseller.

Machine - 9497

Warranty Period* - Three (3) years

*Contact your place of purchase for warranty service information. Some IBM

Machines are eligible for On-site warranty service depending on the country where

service is performed.

The IBM Warranty for Machines

IBM warrants that each Machine 1) is free from defects in materials and

workmanship and 2) conforms to IBM's Official Published Specifications. The

warranty period for a Machine is a specified, fixed period commencing on its

Date of Installation. The date on your sales receipt is the Date of Installation,

unless IBM or your reseller informs you otherwise.

During the warranty period IBM or your reseller, if approved by IBM to provide

warranty service, will provide repair and exchange service for the Machine,

without charge, under the type of service designated for the Machine and will

manage and install engineering changes that apply to the Machine.

If a Machine does not function as warranted during the warranty period, and

IBM or your reseller are unable to either 1) make it do so or 2) replace it with

one that is at least functionally equivalent, you may return it to your place of

purchase and your money will be refunded. The replacement may not be new,

but will be in good working order.

Extent of Warranty

The warranty does not cover the repair or exchange of a Machine resulting

from misuse, accident, modification, unsuitable physical or operating

environment, improper maintenance by you, or failure caused by a product for

which IBM is not responsible. The warranty is voided by removal or alteration

of Machine or parts identification labels.

THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND

REPLACE ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE. THESE WARRANTIES GIVE YOU

SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS

WHICH VARY FROM JURISDICTION TO JURISDICTION. SOME

JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION OR

LIMITATION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH

WARRANTIES ARE LIMITED IN DURATION TO THE WARRANTY

PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.

Items Not Covered by Warranty

IBM does not warrant uninterrupted or error-free operation of a Machine.

Unless specified otherwise, IBM provides non-IBM machines WITHOUT

WARRANTIES OF ANY KIND.

%ꢋꢛꢅ ꢉ ꢎꢇꢋꢊꢎꢏꢕꢅ ꢖꢐꢅ ꢖꢉꢇ ꢐꢅ ꢈꢓꢚꢚꢖꢐꢉꢅ ꢚꢐꢖ&ꢊꢑ ꢑꢅ 'ꢖꢐꢅ ꢏꢅ (ꢏꢎꢇꢊꢋ ꢅ ꢓꢋꢑ ꢐꢅ ꢍꢏꢐꢐꢏꢋꢉꢛ)ꢅ ꢈꢓꢎꢇꢅ ꢏꢈ

ꢏꢈꢈꢊꢈꢉꢏꢋꢎ ꢅ &ꢊꢏꢅ ꢉ ꢕ ꢚꢇꢖꢋ ꢅ ꢍꢊꢉꢇꢅ *ꢇꢖꢍꢘꢉꢖ*ꢅ +ꢓ ꢈꢉꢊꢖꢋꢈꢅ ꢏꢋꢑꢅ ꢉꢇꢖꢈ ꢅ regarding Machine

set-up and installation will be provided WITHOUT WARRANTIES OF ANY

KIND.

Warranty Service

To obtain warranty service for the Machine, contact your reseller or IBM. You

may be required to present proof of purchase.

IBM or your reseller provides certain types of repair and exchange service,

either at your location or at a service center, to keep Machines in, or restore

them to, conformance with their Specifications. IBM or your reseller will inform

you of the available types of service for a Machine based on its country of

installation. IBM may repair the failing Machine or exchange it at its discretion.

When warranty service involves the exchange of a Machine or part, the item

IBM or your reseller replaces becomes its property and the replacement

becomes yours. You represent that all removed items are genuine and

unaltered. The replacement may not be new, but will be in good working order

and at least functionally equivalent to the item replaced. The replacement

assumes the warranty service status of the replaced item.

Any feature, conversion, or upgrade IBM or your reseller services must be

installed on a Machine which is 1) for certain Machines, the designated,

serial-numbered Machine and 2) at an engineering-change level compatible

with the feature, conversion, or upgrade. Many features, conversions, or

upgrades involve the removal of parts and their return to IBM. A part that

replaces a removed part will assume the warranty service status of the

removed part.

Before IBM or your reseller exchanges a Machine or part, you agree to

remove all features, parts, options, alterations, and attachments not under

warranty service.

You also agree to ensure that the Machine is free of any legal obligations or

restrictions that prevent its exchange; obtain authorization from the owner to

have IBM or your reseller service a Machine that you do not own; and where

applicable, before service is provided follow the problem determination,

problem analysis, and service request procedures that IBM or your reseller

provides, secure all programs, data, and funds contained in a Machine,

provide IBM or your reseller with sufficient, free, and safe access to your

facilities to permit them to fulfill their obligations, and inform IBM or your

reseller of changes in a Machine's location.

IBM is responsible for loss of, or damage to, your Machine while it is 1) in

IBM's possession or 2) in transit in those cases where IBM is responsible for

the transportation charges.

Neither IBM nor your reseller is responsible for any of your confidential,

proprietary or personal information contained in a Machine which you return

to IBM or your reseller for any reason. You should remove all such information

from the Machine prior to its ꢐ ꢉꢓꢐꢋꢁ

Production Status

Each IBM Machine is manufactured from new parts, or new and used parts. In

some cases, the Machine may not be new and may have been previously

installed. Regardless of the Machine's production status, IBM's appropriate

warranty terms apply.

Limitation of Liability

Circumstances may arise where, because of default on IBM's part or other

liability, you are entitled to recover damages from IBM. In each such instance,

regardless of the basis on which you are entitled to claim damages from IBM

(including fundamental breach, negligence, misrepresentation, or other

contract or tort claim), IBM is liable for no more than damages for bodily injury

(including death) and damage to real property and tangible personal property;

and

The amount of any other actual direct damages, up to the greater of U.S.

$100,000 (or equivalent in local currency) or the charges (if recurring, 12

months' charges apply) for the Machine that is the subject of the claim.

This limit also applies to IBM's suppliers and your reseller. It is the maximum

for which IBM, its suppliers, and your reseller are collectively responsible.

UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE

FOLLOWING: 1) THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES

(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2)

LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR 3) SPECIAL,

INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC

CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR

SAVINGS), EVEN IF IBM, ITS SUPPLIERS OR YOUR RESELLER IS

INFORMED OF THEIR POSSIBILITY. SOME JURISDICTIONS DO NOT

ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

Statement of Warranty Part 2 - Country-unique Terms

ASIA PACIFIC

AUSTRALIA: The IBM Warranty for Machines: The following paragraph is

added to this Section:

The warranties specified in this Section are in addition to any rights you may

have under the Trade Practices Act 1974 or other legislation and are only

limited to the extent permitted by the applicable legislation.

Extent of Warranty: The following replaces the first and second sentences of

this Section:

The warranty does not cover the repair or exchange of a Machine resulting

from misuse, accident, modification, unsuitable physical or operating

environment, operation in other than the Specified Operating Environment,

improper maintenance by you, or failure caused by a product for which IBM is

not responsible.

Limitation of Liability: The following is added to this Section:

Where IBM is in breach of a condition or warranty implied by the Trade

Practices Act 1974, IBM's liability is limited to the repair or replacement of the

goods or the supply of equivalent goods. Where that condition or warranty

relates to right to sell, quiet possession or clear title, or the goods are of a kind

ordinarily acquired for personal, domestic or household use or consumption,

then none of the limitations in this paragraph apply.

PEOPLE'S REPUBLIC OF CHINA: Governing Law: The following is added

to this Statement:

The laws of the State of New York govern this Statement.

INDIA: Limitation of Liability: The following replaces items 1 and 2 of this

Section:

1. liability for bodily injury (including death) or damage to real property and

tangible personal property will be limited to that caused by IBM's negligence;

2. as to any other actual damage arising in any situation involving

nonperformance by IBM pursuant to, or in any way related to the subject of

this Statement of Warranty, IBM's liability will be limited to the charge paid by

you for the individual Machine that is the subject of the claim.

NEW ZEALAND: The IBM Warranty for Machines: The following paragraph

is added to this Section:

The warranties specified in this Section are in addition to any rights you may

have under the Consumer Guarantees Act 1993 or other legislation which

cannot be excluded or limited. The Consumer Guarantees Act 1993 will not

apply in respect of any goods which IBM provides, if you require the goods for

the purposes of a business as defined in that Act.

Limitation of Liability: The following is added to this Section:

Where Machines are not acquired for the purposes of a business as defined

in the Consumer Guarantees Act 1993, the limitations in this Section are

subject to the limitations in that Act.

EUROPE, MIDDLE EAST, AFRICA (EMEA)

The following terms apply to all EMEA countries.

The terms of this Statement of Warranty apply to Machines purchased from

an IBM reseller. If you purchased this Machine from IBM, the terms and

conditions of the applicable IBM agreement prevail over this warranty

statement.

Warranty Service

If you purchased an IBM Machine in Austria, Belgium, Denmark, Estonia,

Finland, France, Germany, Greece, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland or

United Kingdom, you may obtain warranty service for that Machine in any of

those countries from either (1) ꢏꢋꢅ ,-(ꢅꢐ ꢈ ꢕꢕ ꢐꢅꢏꢚꢚꢐꢖ& ꢑꢅꢉꢖꢅꢚ ꢐ'ꢖꢐ$ꢅ ꢍꢏꢐꢐꢏꢋꢉꢛ

ꢈ ꢐ&ꢊꢎ ꢅꢖꢐꢅꢜꢂ ꢅ'ꢐꢖ$ꢅ,-(ꢁ

If you purchased an IBM Personal Computer Machine in Albania, Armenia,

Belarus, Bosnia and Herzegovina, Bulgaria, Croatia, Czech Republic,

Georgia, Hungary, Kazakhstan, Kirghizia, Federal Republic of Yugoslavia,

Former Yugoslav Republic of Macedonia (FYROM), Moldova, Poland,

Romania, Russia, Slovak Republic, Slovenia, or Ukraine, you may obtain

warranty service for that Machine in any of those countries from either (1) an

IBM reseller approved to perform warranty service or (2) from IBM.

The applicable laws, Country-unique terms and competent court for this

Statement are those of the country in which the warranty service is being

provided. However, the laws of Austria govern this Statement if the warranty

service is provided in Albania, Armenia, Belarus, Bosnia and Herzegovina,

Bulgaria, Croatia, Czech Republic, Federal Republic of Yugoslavia, Georgia,

Hungary, Kazakhstan, Kirghizia, Former Yugoslav Republic of Macedonia

(FYROM), Moldova, Poland, Romania, Russia, Slovak Republic, Slovenia,

and Ukraine.

The following terms apply to the country specified:

EGYPT: Limitation of Liability: The following replaces item 2 in this Section:

2. as to any other actual direct damages, IBM's liability will be limited to the

total amount you paid for the Machine that is the subject of the claim.

Applicability of suppliers and resellers (unchanged).

FRANCE: Limitation of Liability: The following replaces the second

sentence of the first paragraph of this Section:

In such instances, regardless of the basis on which you are entitled to claim

damages from IBM, IBM is liable for no more than: (items 1 and 2

unchanged).

GERMANY: The IBM Warranty for Machines: The following replaces the

first sentence of the first paragraph of this Section:

The warranty for an IBM Machine covers the functionality of the Machine for

its normal use and the Machine's conformity to its Specifications.

The following paragraphs are added to this Section:

The minimum warranty period for Machines is six months.

In case IBM or your reseller are unable to repair an IBM Machine, you can

alternatively ask for a partial refund as far as justified by the reduced value of

the unrepaired Machine or ask for a cancellation of the respective agreement

for such Machine and get your money refunded.

Extent of Warranty: The second paragraph does not apply.

Warranty Service: The following is added to this Section:

During the warranty period, transportation for delivery of the failing Machine to

IBM will be at IBM's expense.

Production Status: The following paragraph replaces this Section:

Each Machine is newly manufactured. It may incorporate in addition to new

parts, re-used parts as well.

Limitation of Liability: The following is added to this Section:

The limitations and exclusions specified in the Statement of Warranty will not

apply to damages caused by IBM with fraud or gross negligence and for

express warranty.

In item 2, replace "U.S. $100,000" with "1.000.000 DEM."

The following sentence is added to the end of the first paragraph of item 2:

IBM's liability under this item is limited to the violation of essential contractual

terms in cases of ordinary negligence.

IRELAND: Extent of Warranty: The following is added to this Section:

Except as expressly provided in these terms and conditions, all statutory

conditions, including all warranties implied, but without prejudice to the

generality of the foregoing all warranties implied by the Sale of Goods Act

1893 or the Sale of Goods and Supply of Services Act 1980 are hereby

excluded.

Limitation of Liability: The following replaces items one and two of the first

paragraph of this Section:

1. death or personal injury or physical damage to your real property solely

caused by IBM's negligence; and 2. the amount of any other actual direct

damages, up to the greater of Irish Pounds 75,000 or 125 percent of the

charges (if recurring, the 12 months' charges apply) for the Machine that is the

subject of the claim or which otherwise gives rise to the claim.

Applicability of suppliers and resellers (unchanged).

The following paragraph is added at the end of this Section:

IBM's entire liability and your sole remedy, whether in contract or in tort, in

respect of any default shall be limited to damages.

ITALY: Limitation of Liability: The following replaces the second sentence

in the first paragraph:

In each such instance unless otherwise provided by mandatory law, IBM is

liable for no more than: (item 1 unchanged) 2)as to any other actual damage

arising in all situations involving non-performance by IBM pursuant to, or in

any way related to the subject matter of this Statement of Warranty, IBM's

liability, will be limited to the total amount you paid for the Machine that is the

subject of the claim.

Applicability of suppliers and resellers (unchanged).

The following replaces the second paragraph of this Section:

Unless otherwise provided by mandatory law, IBM and your reseller are not

liable for any of the following: (items 1 and 2 unchanged) 3) indirect damages,

even if IBM or your reseller is informed of their possibility.

SOUTH AFRICA, NAMIBIA, BOTSWANA, LESOTHO AND SWAZILAND:

Limitation of Liability: The following is added to this Section:

IBM's entire liability to you for actual damages arising in all situations involving

nonperformance by IBM in respect of the subject matter of this Statement of

Warranty will be limited to the charge paid by you for the individual Machine

that is the subject of your claim from IBM.

TURKIYE: Production Status: The following replaces this Section:

IBM fulfills customer orders for IBM Machines as newly manufactured in

accordance with IBM's production standards.

UNITED KINGDOM: Limitation of Liability: The following replaces items 1

and 2 of the first paragraph of this Section:

1. death or personal injury or physical damage to your real property solely

caused by IBM's negligence;

2. the amount of any other actual direct damages or loss, up to the greater of

Pounds Sterling 150,000 or 125 percent of the charges (if recurring, the 12

months' charges apply) for the Machine that is the subject of the claim or

which otherwise gives rise to the claim.

The following item is added to this paragraph:

3. breach of IBM's obligations implied by Section 12 of the Sale of Goods Act

1979 or Section 2 of the Supply of Goods and Services Act 1982.

Applicability of suppliers and resellers (unchanged).

The following is added to the end of this Section:

IBM's entire liability and your sole remedy, whether in contract or

in tort, in respect of any default will be limited to damages.

NORTH AMERICA

CANADA: Warranty Service: The following is added to this Section:

To obtain warranty service from IBM, call 1-800-565-3344.

UNITED STATES OF AMERICA: Warranty Service: The following is added

to this Section:

To obtain warranty service from IBM, call 1-800-772-2227.

IBM Statement of Limited Warranty for United States, Puerto Rico, and

Canada (Part 1 - General Terms)

This Statement of Limited Warranty includes Part 1 - General Terms and Part

2 - Country-unique Terms. The terms of Part 2 may replace or modify

those of Part 1. The warranties provided by IBM in this Statement of Limited

Warranty apply only to Machines you purchase for your use, and not for

resale, from IBM or your reseller. The term "Machine" means an IBM machine,

its features, conversions, upgrades, elements, or accessories, or any

combination of them. The term "Machine" does not include any software

programs, whether pre-loaded with the Machine, installed subsequently or

otherwise. Unless IBM specifies otherwise, the following warranties apply

only in the country where you acquire the Machine. Nothing in this Statement

of Warranty affects any statutory rights of consumers that cannot be waived or

limited by contract. If you have any questions, contact IBM or your reseller.

Machine - 9497

Warranty Period* - Three (3) years

*Contact your place of purchase for warranty service information. Some IBM

Machines are eligible for On-site warranty service depending on the country

where service is performed.