IH-W355NB
IH-W356NP
MyLife™ notebook webcam pro
5.0 megapixel max resolution
Congratulations on the purchase of your
new MyLife notebook webcam pro. This
product comes with a limited lifetime
warranty.
Before using your product, please thoroughly
read and follow the instructions inside this
manual.
If you still need help, see the back page for
other support options.
If you want to know more about our
products, visit us online at
system requirements
• Windows® XP Service Pack 2 or
Windows Vista®
• USB port (a USB 2.0 port is required for
optimal performance)
• CD-ROM drive
user manual
your new webcam
install software
lens
1. Insert the installation CD into your computer. On the
screen that appears, click the application you want to
install: ArcSoft Magic-i or ArcSoft WebCam Companion.
power indicator
microphone
MyLife notebook webcam pro
Model # IH-W355NB/IH-W356NP
ArcSoft Magic-i™
ArcSoft Webcam Companion®
clip
fnnte You must install the software before connecting
exit
your webcam to your computer.
2008© LifeWorks Technology Group LLC.
iHome™ is a trademark of SDI Technologies Inc.
used under license.
2. Select a language and click OK.
3. An InstallShield Wizard dialog box displays. Click Next.
Click Yes to accept the license agreement, then click
Next to accept the default installation location.
3
4. A Select Program Folder dialog box displays. Click
Next.
2. Clip the webcam onto the top of your notebook’s screen.
5. After the application finishes installing, an InstallShield
Wizard Complete dialog box displays. Click Finish to
exit the wizard.
6. The main software installation screen displays again.
Repeat the above steps to install the other application. Click
exit on the main software installation screen when done.
connect hardware
1. Connect the USB cable between the bottom of your
webcam and a USB port on your computer.
use your webcam
You can start using your webcam immediately for video
conferencing with one of the many video conferencing
services available over the internet. Additional features
are available through the included ArcSoft WebCam
Companion and Magic-i software applications.
4
capture still shots or video
advanced features
Click Start > All Programs > ArcSoft WebCam
Companion 2 > WebCam Companion 2 to open the Start
Page.
1. On the Start Page, click Capture. The Capture window
displays.
• For a still shot, click Capture.
• To record a video clip, click Record Video. When done,
click Stop Recording.
5
2. Click Monitor Settings to configure your monitor. Click
Save when done.
monitor an area
ArcSoft WebCam Companion allows you to use your
webcam to monitor an area, recording video when there is
any motion in the area. To monitor an area:
motion
sensitivity
level
1. On the Start Page, click Monitor. The Monitor window
displays.
send snapshot
via email or FTP
when motion is
detected
3. Click Start Monitor to begin monitoring. The monitor will
record video whenever it detects motion.
Click Stop Monitor to end the monitoring session.
6
change video settings
zoom
To change video settings and access other webcam settings, Your webcam can zoom in as much as 4×. To change the
click the WebCam Settings button in the Capture window
(see “capture still shots or video” on page 5) or the Monitor
window (see “monitor an area” on page 6).
zoom level when using ArcSoft WebCam Companion:
1. Click the WebCam Settings button in the Capture
or Monitor window (see “change video settings” on
page 7).
2. The webcam properties dialog box displays. Select the
Camera Control tab.
The webcam properties dialog box displays.
3. Click and drag the Zoom slider to change the zoom
level, left to zoom out and right to zoom in.
Here you can change image, video and camera settings.
4. Click OK.
7
view and edit still shots and video
special effects
Click Start > All Programs > ArcSoft Magic-i 3 > Magic-i 3
to open the Effects Page.
To view the still shots or video you have captured, click Edit
on the Start Page. Here you can also edit your still shots
and video, including auto enhancing your photos.
Click the Capture tab for recordings made from the Capture
window (see “capture still shots or video” on page 5).
Click the Monitor tab for recordings made by the webcam
monitor (see “monitor an area” on page 6).
Use this page to configure all special effects.
Before beginning, select your webcam (USB Video Device)
at the top of the window.
8
use an avatar
An avatar is an image you use as your personal
representation online. Instead of your face showing, your
avatar displays. To use an avatar:
1. In ArcSoft Magic-i, select the Avatar tab.
3
1
2
zoom face tracking
zoom
Your webcam can zoom in as much as 4×. To change the
zoom level when using special effects in ArcSoft Magic-i,
click the zoom buttons underneath the picture.
turn on face tracking
Face tracking keeps the camera trained on a person’s face
without mechanically moving the camera if the person
moves around in the chair. To turn on face tracking, click the
face tracking button underneath the picture.
2. Select an avatar.
3. Select Enable effect.
9
use other special effects
Various other special effects are available under the Effect
and Illustration tabs. To turn on a special effect:
product operating tips
• Your webcam operates best if you sit about 3 ft. (1 m)
from the camera. This ensures the picture is not distorted
and that the microphone can easily pick up your voice.
• Click Help > Application Help in ArcSoft WebCam
Companion or the question mark at the top right of the
ArcSoft Magic-i window for more details on how to use
each application with your webcam.
1. Select either the Effect or Illustration tab, depending
on the effect you want. The Effect tab gives you various
image effects, and the Illustration tab gives you different
picture frames you can use.
4
1
troubleshooting
2
3
situation try this
no video is • Ensure the webcam is connected to the
displayed
computer.
• Use a different USB port.
• Connect the webcam to a USB port on the
computer, not a USB hub.
• Uninstall and reinstall the software. To uninstall
the software, click Start > Control Panel > Add
or Remove Programs, select the application
(ArcSoft Magic-i 3 or ArcSoft WebCam
Companion 2) and click Change/Remove.
2. Select a subcategory by clicking its title bar.
3. Select the effect you want.
video stutters • Disconnect and reconnect the webcam.
or stops
• Ensure the webcam is connected to a USB 2.0
port (not a slower USB 1.1 port).
4. Select Enable effect.
10
FCC Statement
Warning
This device complies with part 15 of FCC Rules. Operation
is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of FCC Rules. These
limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction guide, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Improper setup, use and care of this product can increase
the risk of serious injury, death or device damage. Read
and keep this guide and all other printed guides for future
reference. For updated guides or replacements, go to
Do Not Attempt Repairs
Do not attempt to take apart, open, repair, service or
modify the device(s). Doing so may risk electric shock or
other hazard. Evidence of any attempt to open or modify
the device, including any peeling, puncture or removal of
labels, will void the Limited Lifetime Warranty.
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
the receiver.
•
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult a service representative for help.
Properly shielded and grounded cables and connectors
must be used in order to comply with FCC emission limits.
LifeWorks is not responsible for any radio or television
interference caused by using other than recommended
cables and connectors or by unauthorized changes or
modifications to this equipment. Unauthorized changes or
modifications could void the user’s authority to operate the
equipment.
Responsible party:
LifeWorks Technology Group LLC
1412 Broadway
New York, NY 10018
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Printed in China
© 2008 LifeWorks Technology Group LLC.
iHome™ is a trademark of SDI Technologies Inc. used
under license.
Windows Vista® is a registered trademark or trademark of
Microsoft Corporation in the United States and/or other
countries.
All other brands and logos are trademarks of their
respective companies.
technical support
for technical support please visit
or call (877) LIFE-540
(877-543-3540)
lifetime warranty
for model numbers
for warranty information, please visit
IH-W355NB
IH-W356NP
document version number 0811-0
|