USB 3.0/eSATA to SATA III HDD Dock with
Fan and UASP
SDOCKU33EF
*actual product may vary from photo
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
Manual Revision: 12/08/2014
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Front View.................................................................................................................................................... 2
Rear View...................................................................................................................................................... 2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
Driver Installation...................................................................................................................................... 4
Using the Storage Device......................................................................5
Technical Support ..................................................................................7
Warranty Information............................................................................7
Instruction Manual
i
Introduction
The SATDOCKU3SEF eSATA/USB 3.0 to SATA Hard Drive Docking Station with Fan
delivers quick and easy access to a 2.5in or 3.5in SATA hard disk drive (HDD) or solid
state drive (SSD) through either eSATA or USB connectivity, making it compatible
with almost any system. A built-in 80mm cooling fan provides increased reliability
and lifespan to HDDs, while also making them easier to handle when it comes time
to remove them from the dock. The variable fan speed control allows for on-the-fly
adjustments for any type of HDD or to balance cooling with noise. eSATA provides
data transfer rates up to 3 Gbps, while USB 3.0 provides up to 5 Gbps while still being
backwards compatible with USB 2.0 systems at 480 Mbps. Extending the versatility
with the SATA to IDE hard drive adapter (SAT2IDEADP) allows for 2.5in or 3.5in IDE HDD
to be used in a SATA dock.
Packaging Contents
•
•
•
•
•
1x eSATA / USB 3.0 SATA HDD DOCK
1x 1m USB 3.0 Cable
1x 1m eSATA Cable
1x Universal Power Adapter (NA/UK/EU/AUS)
1x Instruction Manual
System Requirements
•
USB enabled computer system with available USB port
or
SATA enabled computer system with available eSATA port
Available AC electrical outlet
•
Instruction Manual
1
Front View
Rear View
Instruction Manual
2
Installation
WARNING! Hard drives and storage enclosures require careful handling, especially
when being transported. If you are not careful with your hard disk, lost data may
result. Always handle your hard drive and storage device with caution. Be sure that
you are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.
Hardware Installation
1. Connect the external power adapter from the hard drive dock to an electrical outlet.
2. Insert a 2.5”or 3.5”hard drive into the top loading slot. Make sure that the
connectors on the hard drive are facing the same corner of the slot that has a cutout
in the door. The label on the hard drive should face the front of the hard drive dock.
3. Connect the included USB 3.0 cable from the hard drive dock to an available USB 3.0
or 2.0 port on the computer system. The computer can be on or off.
NOTE: A USB 2.0 A-B cable could be used as a substitute on the hard drive dock but
will be restricted to USB 2.0 speeds.
or
Connect the included eSATA cable from the hard drive dock to an available eSATA port
on the computer system. The computer can be on or off.
NOTE: It is not recommended that both USB and eSATA be connected at the same
time, however eSATA will be the default connection if both are connected.
4. Press the power button on the rear of the hard drive dock. The Power LED next to
the power button as well as the LED on the top of the dock will light up.
NOTE: If no host connection is detected (USB cable unplugged or computer turned
off), the dock will automatically go into Suspend Mode and power down the SATA
drive until an active host connection is detected. The LED on the top of the dock will
turn off however the LED on the rear of the dock will stay lit.
5. The operating system will automatically detect and install the SATA drive. Once
complete, the drive should be ready for use.
6. Adjust the fan speed control dial on the side of the docking station, to the desired
speed or turn it off completely.
Instruction Manual
3
NOTE: When connected via USB, the Dock will automatically go into Suspend Mode
if the connection is left idle for more than 5 minutes. The SATA drive will be powered
down and the fan stopped still visible to the operating system (the LED on the top
of the dock will also turn off however the LED on the rear of the dock will stay lit).
Accessing the SATA drive will automatically cancel Suspend Mode and power the drive
back up. This does not apply to eSATA connections, which are always active.
7. To remove the hard drive, make sure it is currently not being accessed by the
computer then unmount or uninstall the disk drive from the operating system (see
documentation for your operating system).
8. Press the power button to turn off the hard drive dock and wait for the drive to
power down.
9. Press the drive ejection button on the top of the hard drive dock to release the drive
then pull the drive from the slot.
Driver Installation
No driver installation is required for the compatible operating systems, as this
enclosure is natively supported, so the drivers are already installed.
Instruction Manual
4
Using the Storage Device
Windows
If you are using a brand new hard drive that does not contain any data, then you will
first need to prepare the hard drive for use. From the main desktop, right-click on
“My Computer”(“Computer”in Vista/7), then select Manage. In the new Computer
Management window, select Disk Management from the left window panel.
Locate the Disk that says it is “Unallocated”(check hard drive capacity to confirm it’s the
correct hard drive) and then right-click in the section that says “Unallocated”and select
“New Partition”.
Instruction Manual
5
The New Partition Wizard will appear. Follow the instructions in the wizard to
complete setting up the drive. Once complete, the Disk should show up as “Healthy”
with a drive letter assigned (i.e. E:). This drive letter should now appear within
My Computer.
If you are installing a hard drive that already has data on it, then after plugging it in, the
drive should automatically show up with a drive letter assigned within My Computer.
Instruction Manual
6
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
documentation, and downloads.
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
7
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you find the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.
|