STIGA VILLA
ROYAL
PRESIDENT
SENATOR
COMFORT
MASTER
8211-0288-01
VILLA
2
5
3
4
4.
5.
95
7. Master - Senator - Comfort - President
6.
OPEN
8. Royal
9.
N
10. Master - Senator - Comfort - President
11. Royal
VILLA
13. Royal
12. Master - Senator - Comfort - President
0.75 mm
15. Master - Senator - Comfort - President
14.
UPPER
LOWER
5
17.
16.
18.
GB
ENGLISH
To lift up the accessory, press down the pedal as far
as it goes. Release the pedal and the accessory lift-
er will now be locked in the lift position.
GENERAL
This symbol means WARNING. Per-
sonal injury and/or damage to property
can occur if the instructions are not fol-
lowed carefully.
To lower the accessory, press the pedal to release
the lock. Lower the accessory lifter to working po-
sition by slowly lifting your foot from the pedal.
2A. SERVICE BRAKE/CLUTCH
(Master - Senator - Comfort)
You must read these operating instruc-
tions and the enclosed pamphlet
“SAFETY INSTRUCTIONS”carefully
before starting the machine.
Pedal which combines both the service brake and
clutch. Three positions:
SYMBOLS
1. Pedal released – forward drive
engaged. The machine starts to
move if a gear is engaged. The
service brake is not activated.
The following symbols are displayed on the ma-
chine to remind you of the care and attention re-
quired when using the machine.
2. Pedal pressed halfway down –
front drive disengaged, it is not
possible to change gear. The
service brake is not activated.
The symbols mean:
Warning!
Read the instruction book and safety man-
ual before using the machine.
3. Pedal pressed fully down –
front drive disengaged The serv-
ice brake is fully activated.
Warning!
Beware of objects being flung out. Keep
spectators away.
NOTE! Do not regulate the speed by slipping the
clutch. Use a suitable gear instead to obtain the
right speed.
Warning!
Always use hearing protectors.
2B. SERVICE BRAKE
(President - Royal)
Warning!
This machine is not intended to be driven
on public roads.
Pedal which activates the machine’s brake system.
Three positions:
Warning!
The machine, equipped with original ac-
cessories, must not be driven in any direc-
tion on slopes with a gradient of more than
10°.
1. Pedal released – forward drive
not engaged.
2. Pedal pressed halfway – front
drive disengaged The service
brake is not activated.
Warning!
Risk for burn injuries. Do not touch the si-
lencer.
3. Pedal pressed fully down –
front drive disengaged The serv-
ice brake is fully activated.
CONTROLS AND
INSTRUMENTS
3. PARKING BRAKE
Inhibitor to lock the brake pedal in depressed posi-
tion.
Items 1 - 9, see figures 1 - 3.
Press down the brake pedal fully. Move
the inhibitor to the right and then release
the brake pedal.
1. ACCESSORY LIFTER
Pedal for lifting front-mounted accessories to
transport position.
The parking brake is released by pressing the brake
pedal. The spring-loaded inhibitor slides to one side.
5
GB
ENGLISH
Make sure that the parking brake is released when
driving.
The clutch pedal must be depressed when chang-
ing gear.
NOTE! Make sure that the machine is standing
completely still before changing from reverse to
forward gear, or vice versa. If a gear does not en-
gage immediately, release the clutch and then press
it in again. Engage the gear again. Never force a
gear in!
4. DRIVE PEDAL (President - Royal)
Pedal which activates the variable transmission.
1. Press down the pedal with the
ball of your foot – the machine
moves forwards.
8. POWER TAKE-OFF
2. No pressure on pedal – the
machine is stationary.
Switch for engaging and disengaging the electro-
magnetic power take-off for driving front-mounted
accessories. Two positions:
3. Press down the pedal with your
heel – the machine reverses.
The speed is regulated with the drive pedal. The
more pressure applied on the pedal, the faster the
machine goes.
1. Press in the right side of the switch – the
power take-off engages. The symbol
lights up.
2. Press in the left part of the switch – the
power take-off disengages.
5. THROTTLE/CHOKE CONTROL
Control for setting the engine speed and to choke
the engine for cold start.
9. DISENGAGING LEVER
(President - Royal)
1. Choke – for starting a cold engine. The
choke is located in the top of the groove.
Lever for disengaging the variable transmission.
Enables the machine to be moved by hand without
using the engine. Two positions:
2. Full throttle – when the machine is in
operation, full throttle should always be
used.
1. Lever pressed in – the trans-
mission is engaged for normal
use.
3. Idling.
2. Lever pulled out – the trans-
mission is disengaged. The ma-
chine can be moved by hand.
6. IGNITION LOCK
The machine must not be towed long distances or
at high speed. This can damage the transmission.
Ignition lock used to start and stop the engine. Four
positions:
1. Stop position – the engine is short-
circuited. The key can be removed.
AREAS OF USE
The machine must only be used for the following
tasks with the indicated STIGA original accessories:
2/3. Operating position.
1. Mowing
4. Start position – the electric start motor
is activated when the key is turned to the
spring-loaded start position. Once the en-
gine has started, let the key return to oper-
ating position 2/3.
With mower deck 13-2929 (92M) or 13-2930
(107M).
2. Grass clippings and leaves collection
With towed collector 13-1978 (30") or 13-1950
(42").
7. GEAR LEVER (Master - Senator -
Comfort)
3. Grass and leaves transport
Lever for selecting one of five forward gears in the
gearbox (1-2-3-4-5), neutral (N), or reverse (R).
With dump cart 13-1979 (Standard), 13-1988
(Maxi) or 13-1992 (Combi).
6
GB
ENGLISH
The towing unit must only be loaded with a verti-
cal force of max. 100 N.
Only fill up with petrol outdoors, and
never smoke when filling. Fill up with
petrol before starting the engine. Never
remove the filler cap or fill up with pet-
rol when the engine is running or still
warm.
The pulling force on the tow unit from towed ac-
cessories must be max. 500 N.
NOTE! Before using a trailer – contact your insur-
ance company.
Never completely fill the fuel tank. Leave an emp-
ty space (= at least the entire filler tube plus 1 - 2
cm at the top of the tank) to allow the petrol to ex-
pand when it warms up without overflowing.
NOTE! This machine is not intended to be driven
on public roads.
STARTING AND OPERATING
CHECKING THE OIL LEVEL
(Master - Senator - Comfort - Presi-
dent)
ENGINE CASING
The engine casing must be removed to inspect and
maintain the engine and battery. Removing:
On delivery, the crankcase is filled with SAE 30 oil.
Check the oil level every time before using to
ensure that it is correct. The machine should be
standing on level ground.
1. Lift up the two catches on the rear edge (fig. 4).
2. First pull the engine casing backwards slightly.
Then lift it off.
Wipe clean round the oil dipstick. Release
it and pull out. Wipe, push down fully and
screw it back in.
Fitting:
1. Tilt the seat forward.
Unscrew it and pull out again. Check the oil level.
Top up with oil to the “FULL” mark if the oil level
is below this (fig. 7).
2. Align the casing’s top front pegs to the recesses
in the front of the engine casing (fig. 5). Do not
push the pegs in yet (see item 4 below).
CHECKING THE OIL LEVEL (Royal)
3. Place the casing’s bottom pegs in the groove in
the shock absorber.
On delivery, the crankcase is filled with SAE oil
10W-40.
4. Guide in the two side pegs in the groove in the
front engine casing. Now press forward the
complete casing.
Check the oil level every time before using to
ensure that it is correct. The machine should be
standing on level ground.
5. Finally, push down the two catches.
Wipe clean round the oil dipstick. Release
it and pull out. Wipe, push down fully
without screwing it back in.
The machine must not used without the
engine casing fitted. Risk for burn inju-
ries and pinch injuries.
Pull out again and check the oil level. Top up with
oil to the “FULL” mark if the oil level is below this
(fig. 8).
FILLING THE FUEL TANK
Always use clean unleaded petrol. Never use oil-
mixed 2-stroke petrol (fig. 6).
SAFETY SYSTEM
NOTE! Bear in mind that standard unleaded petrol
is perishable. Never purchase more than what you
can use within 30 days.
This machine is equipped with a safety system that
consists of:
- a switch at the gear lever (only Master, Senator,
Comfort).
- a switch at the brake pedal (only President,
Royal).
Environmentally-friendly petrol is a good choice
of petrol. This type of petrol has a composition that
is less hazardous for people and nature.
- a switch in the seat mounting (all).
Petrol is highly inflammable. Store pet-
rol in specially made containers for this
purpose.
In order to start the machine, the following are nec-
essary:
7
GB
ENGLISH
- gear lever in neutral (only Master, Senator,
Comfort).
- brake pedal pressed down.
- driver sitting on the seat.
STOPPING
Disengage the power take-off. Apply the parking
brake.
Allow the engine to idle for 1 - 2 minutes. Stop the
engine by turning off the starter key.
Always check the operation of the safe-
ty system before using the machine!
Shut off the fuel cock. This is particularly impor-
tant if the machine is to be transported on a trailer
for example.
With the engine running and the driver sitting on
the seat, check as follows:
- select a gear, and lift your weight off the seat –
the engine should stop (only Master, Senator,
Comfort).
If the machine is left unattended, re-
move the lead from the spark plug. Re-
move also the starter key.
- press the drive pedal so that the machine starts to
move, and then release the drive pedal – the ma-
chine should stop (applies to President, Royal).
- engage the power take-off, lift your weight off
the seat – the power take-off should disengage
The engine can be very hot immediately
after the engine is stopped. Do not touch
the silencer, cylinder or cooling flanges
to avoid burn injuries.
OPERATING TIPS
The machine must not be used if the
safety system does not work! Take the
machine to a service agent for inspec-
tion.
Make sure that there is the correct quantity of oil in the
engine when driving on slopes (oil level at “FULL ”).
Be careful when driving on slopes. No
sudden starting or stopping when mov-
ing up or down a slope. Never drive
across a slope. Drive from the top and
down, or from the bottom and up.
STARTING
1. Open the fuel cock (fig. 9).
2. Check that the spark plug cable is in place.
3. Check that the power take-off is disengaged.
When going down slopes greater than
20º the rear wheels can lift from the
ground. However, the mower deck pre-
vents the machine from tipping over
forwards.
4a. Master - Senator - Comfort:
Put the gear lever in neutral.
4b. President - Royal:
Do not keep your foot on the drive pedal.
The machine, equipped with original
accessories, must not be driven in any
direction on slopes with a gradient of
more than 10°.
5. Starting cold engine – put the throttle control in
the choke position. Starting warm engine – put the
throttle control at full throttle (approx. 1 cm behind
the choke position).
Reduce speed on slopes and when mak-
ing sharp turns to prevent the machine
from tipping over, and to make sure you
do not loose control of the machine.
6. Press down the brake pedal fully.
7. Turn the starter key and start the engine.
8. Once the engine has started, move the throttle
control gradually to full throttle if the choke has
been used.
Do not turn the steering wheel to full
lock when driving in top gear and at full
throttle. The machine can tip over.
9. When starting a cold engine let the engine run
for a few minutes before using the machine. This
allows the oil to warm up.
Keep hands and fingers away from the
seat mounting. Risk of pinch injuries.
Never operate the machine without the
engine casing.
When in use, always run the engine at full throttle.
Never drive with the mower deck en-
gaged and lifted up. This will damage
the drive belt to the unit.
8
GB
ENGLISH
CHANGING THE OIL
(Master - Senator - Comfort - Presi-
dent)
SERVICE AND MAINTENANCE
SERVICE PROGRAMME
Change the engine oil for the first time after 5
hours of operation, and then after every 50 hours of
operation or once per season.
STIGA’s Service Programme should be followed
to keep the machine in good condition in terms of
reliability and operational safety, and from an en-
vironmental perspective.
Change the oil more often, every 25 hours of oper-
ation or at least once per season, if the engine has
to operate under very demanding conditions or if
the ambient temperature is high.
The contents of this programme can be found in
the attached service log.
We recommend that an authorised workshop car-
ries out every service. This guarantees that the
work is carried out by trained personnel and with
original spare parts.
Change the oil when the engine is warm. Use a
good grade of oil (service grade SF, SG or SH).
The engine oil may be very hot if it is
drained off directly after switching off
the engine. For this reason allow the en-
gine to cool for a few minutes before
draining the oil.
The service log should be stamped at every serv-
ice. A “fully stamped” service log is a valuable
document that improves the machine’s second-
hand value.
Unscrew the oil drain plug (fig. 10). It is located on
the left side of the engine (machine seen from rear).
PREPARATIONS
Unless otherwise stated, all service and mainte-
nance should be performed when the machine is
stationary and with the engine switched off.
Let the oil run out into a collection vessel. Then
take the oil to a recycling station. Avoid spilling
oil on the V-belts.
Always apply the parking brake to pre-
vent the machine from rolling.
Screw tight the oil drain plug.
Take out the oil dipstick and fill up with new oil to
the “FULL” mark.
To prevent starting the engine involun-
tarily, always release the spark plug
lead from the spark plug and earth it.
Remove the minus lead from the bat-
tery.
Oil capacity:
Master – 1.1 litre
Senator. Comfort, President – 1.4 litre
Oil type, summertime (> 4° C): SAE -30
(SAE 10W-30 can also be used. The oil consump-
tion may increase somewhat if 10W-30 is used.
Check the oil level more regularly if this type of oil
is used.
CLEANING
To reduce the risk of fire, keep the en-
gine, silencer/catalytic converter, bat-
tery and fuel tank, free from grass,
leaves and oil.
Oil type, winter (< 4° C): SAE 5W-30
(if this oil is not available, use SAE 10W-30)
To reduce the risk of fire, regularly
check the machine for oil and/or fuel
leakage.
Do not use any additives with the oil.
Do not overfill. This can result in the engine over-
heating.
When washing the machine with water under high
pressure, do not point the jet directly at the trans-
mission.
CHANGING THE OIL (Royal)
Change the engine oil for the first time after 20
hours of operation (or during the first month), and
then after every 100 hours of operation or every 6
months.
Do not point the jet at the engine. Use a brush or
compressed air to clean it.
Change the oil when the engine is warm. Use a
good grade of oil (service grade SF, SG or SH).
9
GB
ENGLISH
The engine oil may be very hot if it is
drained off directly after switching off
the engine. For this reason allow the en-
gine to cool for a few minutes before
draining the oil.
4. Clean the paper filter as follows: Tap it lightly
against a flat surface. If the filter is very dirty, re-
place it.
5. Assemble in the reverse order.
Petroleum-based solvents such as kerosene must
not be used to clean the paper filter. These solvents
will damage the filter.
Unscrew the oil drain plug in the end of the tube
(fig. 11).
Let the oil run out into a collection vessel. Then
take the oil to a recycling station. Avoid spilling
oil on the V-belts.
Do not use compressed air to clean the paper filter.
The paper filter must not be oiled.
SPARK PLUG
Screw tight the oil drain plug. Make sure that the
fibre gasket and O-ring inside the plug are undam-
aged and in the correct position.
Change the spark plug after every 100 hours of op-
eration or every season. In the accessory bag there
is a spark plug sleeve A and torsion pin B to
change the spark plug.
Take out the oil dipstick and fill up with new oil to
the “FULL” mark.
The engine manufacturer recommends:
Oil capacity:
Royal – 0.9 litre (= when changing; total engine
capacity is 1.15 litre).
Master - Senator - Comfort - President: Champion
J19LM.
Royal: NGK BPR5ES or DENSO W16EPR-U.
Oil type for all seasons: SAE 10W-40.
Fir very low temperatures (< -20° C), use SAE
5W-30.
Correct electrode gap: 0.75 mm (fig. 14).
COOLING AIR INTAKE - ENGINE
(Master - Senator - Comfort - Presi-
dent)
Do not use any additives with the oil.
Do not overfill. This can result in the engine over-
heating.
The engine is air-cooled. A blocked cooling sys-
tem can damage the engine. The engine should be
cleaned every 100 hours of operation or at least
once a year.
AIR FILTER - ENGINE
Master - Senator - Comfort - President:
Clean the pre-filter every year or after every 25 op-
erating hours, whichever comes first.
Remove the fan casing. Clean the cooling fins on
the cylinder, the fan and the rotating protective
grille (fig. 15). Clean more frequently if moving
dry grass.
Clean the paper filter every year or every 100 op-
erating hours, whichever comes first.
Royal:
BATTERY
Clean the air filter (per-filter and paper filter) every
3 months or after every 50 operating hours, which-
ever comes first. Change the paper filter every year
or every 200 operating hours.
Check the acid level regularly.
The acid level should lie between the “UPPER”
and “LOWER” markings on the battery (fig. 16).
When adjusting the acid level, only use distilled
water.
All models:
NOTE! Clean both filters more often if the ma-
chine is used in dusty conditions.
The battery acid is extremely corrosive
and can cause burns on the skin and
clothing. Use rubber gloves and protect
your eyes with protective glasses. Avoid
inhaling the acid fumes.
1. Remove the air filter cover (fig. 12 - 13).
2. Dismantle the paper filter and pre-filter (= foam
plastic filter). Make sure that no dirt gets into the
carburettor. Clean the air filter housing.
3. Wash the pre-filter in liquid detergent and water.
Squeeze dry. Pour a little on the filter and squeeze
in the oil.
10
GB
ENGLISH
Do not tip the battery enough for bat-
PATENT – PROTECTION OF
DESIGNS
tery acid to run out onto your hands
and clothing. If this should happen,
flush with lots of water.
This machine, or parts thereof, is protected by the
following patents and protection of designs:
If the battery terminals are coated with oxide, they
should be cleaned. Clean the battery terminals with
a wire brush and grease them.
9901091-0 (SE), 9901730-3 (SE), SE00/00577
(PCT), SE00/00895 (PCT), 4.537.581 (US).
LUBRICATION - CHASSIS
00 1080 (SE).
The machine has three grease nipples on the rear
axle, which should be lubricated with universal
grease after every 25 operating hours (fig. 17).
Lubricate the steering cables with universal grease
a couple of times per season.
Lubricate the plastic bearings with universal
grease a couple of times per season.
Lubricate the tension arms joints with engine oil a
couple of times per season.
Drop a little engine oil in both ends of the throttle
control cable a couple of times per season.
Master - Senator - Comfort:
The transmission is filled with oil (SAE 80W-90)
on delivery from the factory. If it is not opened
(which must only be done by a specialist) it should
not normally need topping up with oil.
STEERING CABLES
Adjust the steering cables for the first time after 2
– 3 hours of operation, and then after every 25
hours of operation.
Tension the steering cables by tightening up the
nuts (fig. 18). Important! The “screw ends” of the
steering cables should be held firmly during the
adjustment so that the cables are not twisted. Use
an adjustable wrench or the like, inserting it in the
key handles in the ends of the screws.
Tension the cables until they are no longer slack.
Do not tension the cables too hard. This can cause
unnecessary wear on the steering cables and pul-
leys etc.
STIGA reserves the right to modify the product without
giving any prior notice.
11
|