Graco Toddler Furniture 8828 User Manual

Failure to follow these warnings and  
result in serious injury or death fro  
Toddler Bed  
OWNER’S MANUAL  
Model No. ___________  
Serial No. ___________  
Dear Customer,  
Please fill in the model and  
serial numbers above from  
the label on the side  
tube of your new  
toddler bed.  
Strings can cause strangulation.  
DO NOT place items with a string  
around a child’s neck, such as  
hood strings or pacifier cords. DO  
NOT suspend strings over toddler  
bed or attach strings to toys.  
Model No. 8828  
Congratulations on your purchase of a  
Graco® toddler bed!  
Graco is a leader in juvenile products  
designed for your child’s comfort and  
convenience. We believe your Graco®  
toddler bed is a wise choice, promising  
many hours of enjoyment for your child.  
Before using your toddler bed, please take  
a few minutes to read this Owner’s Manual.  
The short time you spend reading these  
instructions will help you use your  
toddler bed properly.  
DO NOT use a water mattress or all  
foam mattress with this toddler bed.  
DO NOT place bed  
where cords from b  
may strangle a chil  
fall out of the windo  
Please save your Owner’s Manual  
for future use.  
Customer Satisfaction  
THIS PRODUCT REQUIRES ADULT ASSEMBLY.  
ALWAYS use a full-size crib mattress, being at least 515/  
(131 cm) in length, 271/  
in. (69 cm) in width, and 4 in. (10  
cm) in thickness.  
Our goal is to make every product the best it can  
be! We are also committed to supporting our  
products after purchase. If you would like to speak  
to Graco about your product, please contact our  
Customer Service Department at 1-800-345-4109  
Our knowledgeable staff will be ready to answer any  
questions you may have concerning parts, use or  
maintenance. When you call, please have the  
model and serial numbers ready so your call  
may be processed quickly and efficiently.  
8
in.  
4
DISCONTINUE USE OF THE TODDLER BED when your  
child weighs more than 50 pounds (23 kg). Use the bed  
with only one child at a time.  
USE ONLY bed rails provided by Graco®.  
© 2000 Graco 606-4-00 606198  
2
 
Assembling the  
Attaching the Headboard and Footboard  
Headboard and Footboard  
Step 1.  
Begin by attaching frame to the  
footboard.  
Step 1.  
Bumps  
Legs have a small side hole near  
one end. For each leg, push end  
with side hole firmly down into  
a plastic foot. Side hole must be  
covered by foot. It may be  
Stand footboard at one end of the  
metal frame with Graco® name fac-  
ing out and four plastic “bumps” of  
the footboard facing toward frame.  
Side hole  
necessary to tap foot on a hard  
surface to get it all the way on.  
Holding footboard upright, grasp  
the two side tubes as shown and  
lift carefully. Rest ends of side  
tubes on the footboard.  
Step 2.  
Assemble headboard and long  
legs. Push open end of one long  
leg onto plastic plug under “knob”  
on one side of headboard.  
Step 2.  
Insert two T-nuts through two  
holes in side tubes and into foot-  
board tube as shown. Place bolts  
into holes on outside of footboard  
tubes and into T-nuts. Tighten  
bolts with enclosed hex wrench.  
Bolt  
Then push leg sideways so the  
rectangular plug on lower side  
of headboard goes into hole on  
side of the leg.  
T-nut  
Attach other long leg in the  
same way to other side of the  
headboard.  
Hex  
wrench  
Repeat on other side of footboard.  
Step 3.  
Assemble the footboard and  
short legs the same way.  
Attach headboard in the same  
This side  
way. The side with the deeper  
faces bed  
recess should be facing the bed  
as shown.  
Step 3.  
Insert a hex head screw into  
lowest hole on each leg and  
into plastic head- or footboard.  
After both endboards have been  
attached to frame, use the hex  
wrench to FIRMLY TIGHTEN all  
eight bolts into their T-nuts.  
Screw  
Tighten screw securely with the  
included hex wrench, but do  
not over-tighten.  
Step 4.  
Repeat for other three legs.  
To create star panel, first twist  
glow-in-the-dark pieces off the  
plastic stem (immediately  
discard stem). From the back  
of the decorative panel, insert  
pieces by pushing firmly in the  
center of each one. (There are  
three different sizes of stars and  
star openings.) Check that all  
stars are used and no holes are  
left empty.  
CHECK that all four legs are  
securely attached to the  
head- and footboards by  
pulling on the legs.  
Hex  
wrench  
Assembling the Frame  
Step 1.  
Line up the side tubes and  
crossbars on the floor as  
shown at right. It may be  
helpful to brace one side tube  
against a wall or stationary  
object. Holes in side tubes  
must face each other.  
Step 5.  
Hold panel in place on headboard  
while inserting five screws through  
back of headboard. (The plastic in  
the screw holes may need to be  
removed.) Tighten screws securely,  
but do not over-tighten.  
Step 2.  
Insert ends of the crossbars  
into holes in the side tubes.  
606-4-00 606198  
5
6
 
Attaching the Mattress Retainers  
Finishing Assembly  
Place a standard full-size crib  
Do not use toddler bed without  
mattress retainers. Mattress may slide.  
mattress—at least 515/  
8
in. (131  
cm) long by 271/  
4
in. (69 cm)  
Step 1.  
wide by 4 in. (10 cm) thick—on  
finished toddler bed frame. The  
mattress must be placed so the two mattress retainers  
on frame are outside of the mattress to prevent it from  
moving. Your toddler bed is now ready to use.  
Mattress  
retainer  
Ribs  
Snap the mattress retainers  
onto the center of the side  
tubes. The ribs of each retainer  
should face the inside of the  
bed frame. Line up the holes of  
the mattress retainers with the  
small holes in the side tubes.  
Instructions for ordering replacement parts:  
Complete form below. Your toddler bed model number MUST be  
included on the form to ensure proper replacement parts. Your model  
number can be found on the label on the side tube of your toddler bed.  
Payment must accompany your order.  
Hex wrench  
Step 2.  
Parts List:  
Price:*  
Fasten each mattress retainer  
to the side tubes with one T-nut  
and bolt. T-nut must be on  
inside of frame. Tighten bolts  
and T-nuts with the hex wrench.  
Side tube ............................................... $ 8.00 (each)  
Crossbar ................................................ $ 5.00 (each)  
Long leg ................................................ $ 7.00 (each)  
Short leg ................................................ $ 5.00 (each)  
Foot ....................................................... $ 5.00 (set of 4)  
Glow-in-the-dark pieces ........................ $ 5.00  
Decorative panel ................................... $ 6.00  
Hardware ............................................... $ 5.00  
Mattress support ................................... $10.00  
Mattress retainer ................................... $ 5.00 (each)  
Headboard ............................................. $12.00  
Footboard .............................................. $12.00  
Left bed rail (as seen from behind headboard) .. $10.00  
Right bed rail (as seen from behind headboard) $10.00  
Bolt  
T-nut  
Step 3.  
Fold edges  
down  
Position mattress support with  
printed side up as shown. Fold  
edges down at creases, and  
place on bed so notches in  
edges fit over the crossbars.  
* Prices subject to change without notice.  
IF YOU NEED HELP: If you have any questions or if you  
need any part not listed, please call toll-free: 1-800-345-4109  
Attaching the Bed Rails  
Return the form below with payment to:  
GRACO CHILDREN’S PRODUCTS INC.  
CUSTOMER SERVICE DEPARTMENT  
P.O. BOX 100, MAIN STREET  
Step 1.  
There are left and right bed rails.  
When installed correctly, the note  
on the bed rails, “THIS SIDE  
MUST FACE MATTRESS,” will  
be to the inside of the bed.  
ELVERSON, PA 19520  
SHIP TO:  
Name  
Model No. (required)  
Serial No. (required)  
Snap bed rails on bed side  
tubes as shown.  
Address  
Side tube  
Crossbar  
City, State, Zip  
Step 2.  
Long leg  
Short leg  
(
)
Telephone  
Lift bed rails and slide them to  
the inside of the headboard.  
Snap to headboard as shown.  
Mattress retainer will fit in the  
recessed area in the bed rails.  
Foot  
Glow-in-dark pieces  
Decorative panel  
Hardware  
Mattress support  
Mattress retainer  
Headboard  
Footboard  
Left bed rail  
Right bed rail  
Check enclosed  
(payable to Graco Children’s  
Products Inc.)  
Be sure bed  
rails are secure. Bed rails must  
be attached to headboard on  
the inside of the post.  
Charge to credit card:  
Visa  
MasterCard  
Discover  
Subtotal:  
Shipping  
& handling*:  
Account #:  
$5.00  
Step 3.  
6% sales tax  
(PA only):  
Repeat on other side. Both bed  
rails must be used. Do not rely  
on wall to keep child in bed. See  
warnings.  
Expiration date:  
Signature:  
Total:  
*$15.00 outside the continental U.S.  
7
8
 

Grandstream Networks Security Camera GXV3611 User Manual
Haier Air Conditioner 0010518181 User Manual
Hans Grohe Plumbing Product 41534XX1 User Manual
Harman Kardon Digital Camera HKTS1 User Manual
Hearth and Home Technologies Indoor Fireplace 5100 I User Manual
Hotpoint Dishwasher SDAL 1200 User Manual
Hotpoint Washer Dryer WDAL 9640 User Manual
HP Hewlett Packard Computer Hardware bc1000 User Manual
HP Hewlett Packard Personal Computer 3010 User Manual
Husqvarna Chainsaw 268 XP User Manual