3-IN-1 WOOD, METAL &
CONCRETE NAILER
MODEL H2910
INSTRUCTION MANUAL
COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
Safety Instructions For Power Tools
10. USE PROPER EXTENSION CORD
15. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and
changing accessories.
for the tool. Make sure your extension
cord is in good condition. Conductor
size should be in accordance with the
chart below. The amperage rating
should be listed on the motor or tool
nameplate. An undersized cord will
cause a drop in line voltage resulting
in loss of power and overheating.
Your extension cord must also con-
tain a ground wire and plug pin.
Always repair or replace extension
cords if they become damaged.
16. DISCONNECT TOOLS before ser-
vicing and changing accessories.
17. REDUCE THE RISK OF UNINTEN-
TIONAL STARTING. Make sure
switch is in off position before plug-
ging in.
18. USE
THE
RECOMMENDED
Consult the
ACCESSORIES.
owner’s manual for recommended
accessories. The use of improper
accessories may cause risk of injury.
Minimum Gauge for Extension Cords
AMP
RATING
0-6
LENGTH
50ft
16
25ft
18
18
16
14
12
10
100ft
16
14
14
12
19. CHECK DAMAGED PARTS. Before
further use of the tool, a guard or
other part that is damaged should be
carefully checked to determine that it
will operate properly and perform its
intended function. Check for align-
ment of moving parts, binding of
moving parts, breakage of parts,
mounting, and any other conditions
that may affect its operation. A guard
or other part that is damaged should
be properly repaired or replaced.
7-10
16
16
12
12
11-12
13-16
17-20
21-30
10
No
10
11. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neckties,
rings, bracelets, or other jewelry
which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
20. NEVER LEAVE TOOL RUNNING
UNATTENDED. Turn the power off,
and do not leave tool until it comes to
a complete stop.
12. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glasses.
21. NEVER ALLOW UNTRAINED
USERS TO RUN THIS TOOL
WHILE UNSUPERVISED.
13. SECURE WORK. Use clamps or a
vise to hold work when practical. It is
safer than using your hand and frees
both hands to operate tool.
22. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL. Seek formal
training or research books or maga-
zines that specialize in power tools.
14. DO NOT OVERREACH. Keep proper
footing and balance at all times.
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
-2-
Basic Nailer Safety
In addition to the rules stated in the previ-
ous section, and those in the warning
boxes throughout this manual, please
observe the following safety tips for your
new nailer:
1. READ THIS ENTIRE MANUAL
BEFORE OPERATING THE NAIL-
ER.
2. ALWAYS DISCONNECT AIR FROM
THE NAILER whenever servicing or
installing nails. During maintenance,
a nailer connected to air may fire acci-
dentally, causing serious personal
injury.
3. DO NOT PLACE HANDS NEAR
NAIL POINT OF ENTRY. Nails can
deflect and tear through the surface
of the workpiece, puncturing your
hand or fingers.
Operating the nailer can propel
objects into the air, causing immedi-
ate eye damage. To protect yourself,
always wear American National
Standards Institute (ANSI) approved
safety glasses or goggles when oper-
ating this equipment. In addition, the
nailer discharges at 85-90 decibels.
To protect your hearing, always wear
ANSI approved ear protection when
operating this tool.
4. NEVER CONNECT THE NAILER TO
PRESSURIZED
OXYGEN
OR
OTHER COMBUSTIBLE GASES as
a power source. Only use filtered,
lubricated, and regulated compressed
air.
5. NEVER USE GASOLINE OR
OTHER FLAMMABLE LIQUIDS TO
CLEAN THE NAILER. Vapors in the
tool will ignite by a spark and cause
the tool to explode.
6. DO NOT CARRY THE NAILER BY
ANY OTHER PART THAN THE
HANDLE, and do not carry the nailer
by the air hose.
7. DO NOT KEEP THE TRIGGER
PULLED ON THE SAFETY YOKE
MECHANISM WHEN CARRYING
OR HOLDING THE TOOL.
Never point the nailer at yourself or
another person! Always pay attention
to the direction the nailer is pointed.
Use this tool with respect and caution
to lessen the possibility of operator or
bystander injury. Ignoring this warn-
ing may result in serious personal
injury.
8. DO NOT USE A CHECK VALVE OR
ANY OTHER FITTING that allows air
to remain in the tool.
-3-
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
INTRODUCTION
Most importantly, we stand behind our
Commentary
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
We are proud to offer the Grizzly Model
H2910 3-IN-1 Wood, Metal & Concrete
Nailer. This model is part of a growing
Grizzly family of fine power tools. When
used according to the guidelines set forth
in this manual, you can expect years of
trouble-free, enjoyable operation and
proof of Grizzly’s commitment to customer
satisfaction.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
The Model H2910 features 360˚
adjustable exhaust, a convenient bottom-
loading magazine, a safety trigger and a
durable plastic carrying case.
We are pleased to provide this manual
with the Model H2910. It was written to
encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. This manual
represents our effort to produce the best
documentation possible.
The specifications, details, and pho-
tographs in this manual represent the
Model H2910 as supplied when the manu-
al was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Read the manual before assembly
and operation. Become familiar with
this tool, its safety instructions, and
its operation before beginning any
work. Serious personal injury may
result if safety or operational infor-
mation is not understood or followed.
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
-4-
Compressed Air System
Safety Yoke Mechanism
The Model H2910 is designed to be oper-
ated at 60-100 psi. Do not exceed the
maximum operating pressure for your
model.
A safety yoke mechanism (bump fire) on
the nose of the nailer acts as a secondary
safety device. When the trigger is pressed,
the nailer will not fire until the safety yoke
mechanism is depressed.
Before you use your new nailer, install the
3
⁄
8" quick connect fitting that comes with the
Before you use your nailer for the first time,
check the safety yoke mechanism to
ensure proper function. To do this:
3
nailer. Install a female ⁄8" fitting on the air
hose. Regulate the air pressure on your air
compressor to barely over the minimum psi
for your model.
1. Make sure the nailer is disconnect-
ed from the air supply!
Many pneumatic tools benefit from an in-
line filter/lubricator/regulator unit. This
attachment is connected by hoses
between the air compressor and the sta-
pler. Using this unit protects your tool from
damaging water build-up, allows you to
adjust and maintain constant air pressure
to your tool, and saves you the inconve-
nience of having to manually lubricate your
tool every time you use it. Check the cur-
rent Grizzly catalog for availability of this
unit. If you plan on installing a filter/lubrica-
tor/regulator unit in your compressed air
system, always follow the connection
instructions that come with the unit.
2. Make sure the magazine is empty and
contains no nails.
3. Make sure the trigger and the safety
yoke mechanism move up and down
without sticking.
4. Connect the nailer to the air supply.
5. Without pressing the trigger,
depress the safety yoke mechanism
against a scrap piece of wood that is
clean and free of any knots, staples,
or other foreign objects. If the nailer
does not fire, then the safety yoke
mechanism is working correctly. If the
nailer does fire when you do this,
immediately disconnect the nailer
from the air supply and call our cus-
tomer service for help.
Similarly if the nailer fires when the trigger
is pulled, without the safety yoke mech-
anism being depressed, then the nailer is
not working properly.
If either of these two conditions develop
after you have used your nailer for a peri-
od of time, check the lubrication of these
mechanisms.
Exceeding the maximum permissible
operating pressure may cause the
nailer to explode, blowing metal frag-
ments in all directions. To protect
yourself from serious personal injury,
DO NOT allow your air compressor to
exceed the recommended pressure
when connected to the nailer!
The safety yoke is
a
mechanical
device that can fail. Never rely on the
safety yoke mechanism as an excuse
to point the tool at yourself or any
bystanders. Serious injury may occur.
-5-
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
OPERATION
5. Push the magazine cover forward
Loading The Nailer
until the magazine latch locks in
place.
To load your nailer:
1. Disconnect the air supply from the
nailer!
Depth Adjustment
1. Rotate the depth adjustment wheel
(shown in Figure 3) clockwise to
increase the nail driving depth.
2. Push the magazine latch in the direc-
tion shown in Figure 1.
2. Rotate the finger wheel counter-clock-
wise to decrease the nail driving
depth.
Figure 1. Releasing magazine latch.
3. Pull back the magazine cover until it
stops.
Figure 3. Depth adjustment wheel.
4. Point the nailer down and insert a
stick of brad nails into the magazine
as shown in Figure 2. Make sure that
the pointed ends of the nails rest in
the slot at the bottom of the magazine.
Operating The Nailer
If you have not read the safety instruc-
tions in this manual, do not operate the
nailer.
Before you operate your nailer, place one
drop of the included oil into the quick con-
nect fitting where the nailer connects to the
air supply. Fire the EMPTY nailer 3-4 times
before beginning, so oil does not come out
onto the project during regular operation.
Figure 2. Loading the nailer.
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
-6-
To operate your nailer:
Clearing Jammed Nails
1. Connect the air supply to the quick
connect fitting.
The most frequent situation with any type
of nailer is a jammed nail. A jam must be
cleared before using the nailer again. The
two places where a jam can occur is the
magazine and the discharge area.
2. Test the loaded nailer for proper pen-
etration. Hold the nailer perpendicular
to the surface of a piece of clean
scrap wood that is thick enough for
the length of nails you have loaded.
Depress the safety yoke mechanism
on your workpiece.
3. Before pressing the trigger, make
sure your free hand is positioned out
of the way of a potential path of a nail
in case of deflection. (Deflection is
caused when the nail changes its
path, resulting in the nail puncturing
the surface of the workpiece as
shown in Figure 4.)
Always disconnect air from the nailer
whenever clearing a jam!
To clear a jam from the magazine:
1. Disconnect the nailer from the air
supply!
2. Open the magazine cover and pull the
magazine all the way back.
3. Locate and remove the jammed nail
with a pair of needle nose pliers.
Close the magazine cover so it latch-
es.
Figure 4. Example of nail deflection.
Besides damaging your workpiece,
deflection can cause injury if your free
hand is securing the workpiece in the
location that the staple/nail deflects.
4. Press the trigger. If the nail drove into
the wood far enough, continue with
your intended operations. If the nail
either went too far or not far enough,
then adjust the air pressure. More air
pressure will make the nail go deeper
and less air pressure will decrease
the nail penetration.
To clear a jam from the discharge area:
1. Disconnect the nailer from the air
supply!
2. Remove all of the nails from the mag-
azine.
3. The jammed nail should now be visi-
ble; remove it from the discharge area
with needle nose pliers.
4. Replace the nails. Push the magazine
closed and snap the quick release
latch back into operating position.
-7-
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
Oiling The Nailer
Cleaning The Nailer
Special oil has been included with your
new Grizzly nailer to help maintain its use-
ful life. Place one drop of oil in the nailer air
inlet (as shown in Figure 5) before every
use. Wipe off any excess oil near the nail-
er exhaust to avoid dust build-up. When
the oil that was included with the nailer has
been completely used, replace with Grizzly
Model G2820 Pneumatic Tool Oil.
Use a good solvent to clean the nose
assembly of the nailer. Always be sure that
the nailer is dry before using it again.
Do not allow dust, chips, sand, etc. into the
air connectors or into the body of the nail-
er; this may result in leaks and damage to
the nailer and the air couplings.
Another option to manual oiling would be
to install a lubricator in your air compressor
line. If your air compressor line already has
a lubricator, then regular lubrication of your
nailer will not be necessary. Just make
sure there is always oil in the lubricator.
As mentioned before, the best option is to
install a filter/lubricator/regulator unit such
as the Grizzly Model H2333 in your air line.
Never use gasoline or other flamma-
ble liquids to clean this tool. Vapors
in the tool may ignite, causing the
tool to explode. Ignoring this warning
may lead to serious personal injury or
even death!
Figure 5. Lubricating the nailer via air
inlet.
Always disconnect air from the nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious per-
sonal injury!
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
-8-
Replacing Pistons/O-Rings
If you use your nailer day in and day out,
Grizzly offers repair pistons as cheap
insurance against wasted down time and
lost profits in the event that a piston or pis-
ton shaft becomes worn out. To replace a
piston:
Figure 6. Removing the exhaust cap.
8. With a long flathead screwdriver or
similarly shaped tool, push the piston
shaft back inside the nailer until you
can grip the piston head and remove
it from the cylinder. (Be careful not to
scratch the discharge area when
pushing the piston shaft with the
screwdriver.)
9. Place a new O-ring on the new piston
and apply a thin film of lubricating oil
on the O-ring.
Always disconnect air from the nail-
er whenever servicing! During main-
tenance, a nailer connected to air
may fire accidentally, causing seri-
ous personal injury!
10. Insert the new piston in the cylinder.
Make sure that the grooves on the
piston shaft line up with those on the
guide. The new piston should easily
slide into the cylinder. Do not force
the piston into the cylinder! If the
piston is not easily inserted, double-
check the alignment of the piston
shaft with the grooves on the guide.
11. After the piston is inserted correctly,
close the magazine. Replace the rear
cap assembly and tighten the 4 cap
screws.
1. Disconnect the nailer from the air
supply!
2. Remove all nails from the magazine
cartridge.
3. Remove the 4 cap screws from the
exhaust cap.
4. Remove the exhaust cap as shown in
Figure 6.
12. For more assistance, or to install a
complete O-ring set, refer to the
appropriate breakdown diagram in the
back of this manual.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the head.
6. Open the magazine.
7. Watch the discharge area and push
the top of the piston with your finger.
You will see the piston shaft slide
down the discharge area.
-9-
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
H2910 PART BREAKDOWN
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
-10-
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
01 PH2910001 CAP SCREW
02 PH2910002 CAP COVER
03 PH2910003 SEAL
29 PH2910029 LOCK NUT
30 PH2910030 POSITIONING PLATE
31 PH2910031 ADJUSTMENT NUT
32 PH2910032 GUIDE PLATE
35A PH2910035A BUMP FIRE SWITCH
36 PH2910036 SET SHAFT
37 PH2910037 SAFETY LEVER
38 PH2910038 LOCK WASHER
39 PH2910039 CAP SCREW
40 PH2910040 RUBBER PAD
41 PH2910041 CAP SCREW
42 PH2910042 DIVER GUIDE COVER
43 PH2910043 CAP SCREW
44 PH2910044 CAP SCREW
45 PH2910045 NOSE
04 PH2910004 CAP SCREW
05 PH2910005 SETSCREW
06 PH2910006 CAP
07 PH2910007 PISTON STOPPER
08 PH2910008 O-RING
09 PH2910009 COLLAR
10 PH2910010 O-RING
11 PH2910011 SPRING
12 PH2910012 PISTON HEAD VALVE
13 PH2910013 O-RING
14 PH2910014 O-RING
15 PH2910015 O-RING
16A PH2910016A PISTON ASSEMBLY
17 PH2910017 CYLINDER
18 PH2910018 O-RING
47 PH2910047 BRACKET
48 PH2910048 CAP SCREW
49 PH2910049 MAGAZINE
19 PH2910019 BUMPER
20 PH2910020 GASKET
21 PH2910021 O-RING
50 PH2910050 NAIL GUIDE LINER
51 PH2910051 SPRING
52 PH2910052 PUSHER
22 PH2910022 BODY
53 PH2910053 SET SCREW
54 PH2910054 MAGAZINE COVER
55 PH2910055 ROLLED PIN
56 PH2910056 STOPPER
23 PH2910023 CAP SCREW
24 PH2910024 AIR PLUG
25 PH2910025 JOINT GUIDE
26 PH2910026 STEPPED PIN
27 PH2910027 SPRING
57 PH2910057 MAGAZINE COVER
59 PH2910059 SPRING
28 PH2910028 SAFETY LEVER
-11-
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
TROUBLESHOOTING
CAUSE
PROBLEM
ACTION
1. O-rings in trigger valve
housing are damaged.
1. O-rings must be replaced
Air leaking at trigger valve
area.
&
operation of safety
yoke must be checked.
1. Loose screws in housing.
2. Damaged O-ring.
3. Loose air fitting.
1. Tighten screws.
2. Replace O-ring.
3. Tighten air fitting.
Air leaking between hous-
ing and hose.
1. Damaged seal.
1. Air leaks.
1. Replace damaged seals.
Air leaking between hous-
ing and cap assembly.
1. Tighten screws and fit-
tings.
Tool skips nails while dis-
charging.
2. Dirt in nose.
2. Clean nose.
3. Dirt or damage prevents
nails from moving freely in
magazine.
3. Clean magazine and
inspect/repair damage.
4. Inadequate air flow to tool.
4. Check fitting, hose, com-
pressor & air pressure.
5. Replace piston O-ring.
Lubricate.
5. Worn O-ring on piston or
lack of lubrication.
6. Damaged O-rings on trigger
valve.
6. Replace trigger valve O-
rings.
7. Worn bumper.
8. Cap seal leaking.
7. Replace bumper.
8. Replace cap seal.
1. Tool is not sufficiently lubri-
cated.
2. Broken spring in cap assem-
1. Lubricate tool.
2. Replace spring.
Tool runs slowly or has a
loss of power.
bly.
3. Exhaust port in cap is
blocked.
3. Clean or replace dam-
aged internal parts.
1. Nails are the wrong size.
2. Nails are bent.
3. Magazine or nose screws
are loose.
1. Use correct nails.
2. Use undamaged nails.
3. Tighten magazine and
nose screws.
Fasteners frequently jam
the tool.
4. Driver or driver guide are
worn or damaged.
4. Replace worn or dam-
aged parts.
1. Nail is jammed in maga-
zine or discharge area.
1. Clear tool magazine or
discharge area.
Tool does not fire.
2. Piston shaft is damaged.
3. Air pressure too low.
2. Replace piston shaft.
3. Check/increase air pres-
sure.
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
-12-
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-13-
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model #___________________________ Order #_______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
________________________________________
________________________________________
________________________________________
________________________________________
4. How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
12. What new accessories would you like Grizzly
Industrial to carry?
5. How would you rank your woodworking skills?
________________________________________
________________________________________
________________________________________
________________________________________
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
13. What other companies do you purchase your tools
and supplies from?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
_________________________________________
_________________________________________
_________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
14. Do you think your purchase represents good value?
___Yes
___No
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
15. Would you recommend Grizzly to a friend?
___Yes ___No
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
7. How many of your woodworking machines are
Grizzly? _____________
___Yes
___No
8. Which benchtop tools do you own? Check all
that apply.
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw
___Scroll Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT X
|