NURSERY WAGON WITH
WOOD SIDES
MODEL H3029
INSTRUCTION SHEET
Copyright © August, 2005 By grizzly industriAl, inC.
WARNING: NO pORTION Of THIS MANUAL MAY bE REpRODUCED IN ANY SHApE
OR fORM WITHOUT THE WRITTEN AppROvAL Of GRIzzLY INDUSTRIAL, INC.
#Bl7380 printed in ChinA
ASSEMbLY INSTRUCTIONS
3. Fasten the steering brace to the bed with two
fRONT AXLE ASSEMbLY
M8-1.25 x 20 hex bolts, flat washers, and
lock nuts.
1. With the bed turned upside down, fasten
the front and rear axles (figure 2) to the
bed with four M8-1.25 x 20 hex bolts, flat
washers, and lock nuts. the hex nuts should
face up and the front axle steering supports
should point toward the rear of the cart.
4. insert an M6-1 x 20 hex bolt through the
steering brace, the axle, and the steering
bracket and secure with a flat washer and
lock nut.
5. place the steering bar under the steering
supports and steering bracket, and secure
with M6-1 x 16 hex bolts, flat washers, and
lock nuts as shown in figure 3.
steering
supports
REAR AXLE ASSEMbLY & WHEELS
1. slide a rear axle brace onto each rear axle
and bolt the ends of the braces to the bed
using the remaining M8-1.25 x 20 hex bolts,
flat washers, and lock nuts, as shown in the
parts breakdown.
Front Axle
Assembly
rear Axle
Assembly
2. slide a tire and a 16mm flat washer over
each axle with the tire valve stems facing
outward. insert a cotter pin into each axle
and spread.
figure 2. Axles mounted to the bed.
2. place the steering bracket (figure 3) over
the front axle so the longer length of the
bracket lays over the top of the axle, insert
the front axle stud (figure 3) through the
short length of the bracket, and secure with
a cotter pin.
pULL HANDLE & WOOD SIDES
1. insert the end of the pull handle through
the plastic coupling and mount these to the
front of the steering bracket with a slot head
screw, flat washer, and lock nut.
2. turn the cart over and fasten the metal
brackets to the outside edge of the cart with
M6-1 x 16 flat head screws, flat washers, and
acorn nuts.
long
length
steering
Bracket
3. slide the front, rear, and side panels into the
brackets.
steering
Axle
Bar
If you need additional help with this procedure,
call our Service Department at: (570) 546-9663.
short
Front
steering
Brace
length
Axle stud
figure 3. Front axle assembly.
H3029 parts breakdown and List
12
3
2
1
15
25
23
24
4
7
7
16
26
5
8
6
18
9
17
10
21
11
13
22
19
20
14
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PH3029001
PH3029002
PH3029003
PH3029004
PH3029005
PH3029006
PH3029007
PH3029008
PH3029009
PH3029010
PH3029011
PH3029012
PH3029013
BED
14
15
16
17
18
19
20
21
22
23
24
25
26
PW08M
FLAT WASHER 16MM
HEX BOLT M8-1.25 X 20
FLAT WASHER 8MM
LOCK NUT M8-1.25
2
FRONT PANEL
REAR PANEL
PB09M
3
PW01M
4
REAR AXLE ASSEMBLY
FRONT AXLE ASSEMBLY
STEERING BRACKET
REAR AXLE BRACES
STEERING BRACE
STEERING BAR
PLN04M
PB83M
5
HEX BOLT M6-1 X 16
FLAT WASHER 6MM
LOCK NUT M6-1
6
PW03M
7
PLN03M
PH3029021
PH3029022
PH3029023
PN35M
8
SLOT HEAD SCREW M8-1.25 X 60
PLASTIC COUPLING
METAL BRACKET
9
10
11
12
13
TIRES 4.10/3.50
PULL HANDLE
ACORN NUT M6-1
SIDE PANEL
PFH38M
PB08M
FLAT HD SCR M6-1 X 16
HEX BOLT M6-1 X 20
COTTER PIN 3 X 40
|