Twin-tub Washing Machine with Pump
User's manual
This manual is for
XPB60-113S
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Buzzer
Water-filling entrance
Water inlet selector handle
Wash selector
Outer cover of the spin tub
Inner cover of the spin tub
Spin timer
Wash timer
Spin tub frame
Control panel
Spin tub
Overflow filter
Quick water-filling entrance
Drain hose hook
Water level adjusting lever
Lint filter(Installed by user)
Pulsator
Cabinet
Wash tub
Drain hose
Wash tub cover
Base frame
Meaning and description of the symbols
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damage of the machine or injure the
personal safety of the user.
Warning sign
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Forbidding sign
Please check if the power receptacle has good earthing condition
before using to guarantee your safety.
1
Safety precautions
Please insert the power cord into
special receptacle with rated vol-
tage. Be sure to use single-phase
When the machine is normally
using, please put the power plug
at the location easily to be insert-
three pins receptacle. The earthing ed and extracted by hand. Be sure
terminal of the receptacle must be to pull the plug off when there's
earthed reliably. If possible, please power failure, or the machine is
adopt electric leakage protector.
being moved, cleaned or when it
is idle.
If the supply cord is damaged, it must be replaced
by the manufacturer or its service
agent or a similarly qualified person
in order to avoid a hazard.
Do not use water hotter than 65 C .
Do not put the machine at damp
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
For washing machine with ventilation
openings in the base, that a carpet
must not obstruct the openings.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Ventilation hole at
the bottom of the
washing machine
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
2
Safety precautions
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not decompose, repair or alter the
machine by yourself.
Do not put any hot or heavy items
( such as the kettle with hot water )
on the washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.).
er
Petrol
Thinn
Keep the machine away from direct
sunlight and heat source like the
heater.
Handicapped or children without care
shall not use the machine.
To protect your laundries and wash-
ing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.
It is suggested to use foamless washing
powder.
3
Installation and adjustment
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct operating
the machine.
Install the lint filter
Put the underside of the lint filter into overflow filter
then push the upside into overflow filter
overflow filter
After installation, please refer that the lint filter
installed to the right station, otherwise the lint
filter may be fallen off when washing, influencing
your use.
lint filter
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than 1.2m , or the
drainage will not be smooth enough and cause incomplete drainage.
0.7m<H 1.2m
H
2.Do not step on or press the drain hose.
4
How to change the direction of the drain hoses
Figure 1 indicates the ex factory
installation position of the drain
hose.
Extend the drainhose from the side of spintub.
Take off the drain hose from the hanging
Drain hose
Figure 1
fixing hook
hole of the cabinet. Pull the drain hose
fixing hook outwards gently to take out
the drain hose from the two fixing hooks.
(As per Figure 2)
Side sectional view
Fixing hook
installation hole
Drain hose
fixing hook
Drain hose
Pull outwards
slightly
Rotate the drain hose fixing hook for 90
to take it out from the installation hole
(As per Figure 3).
Take off
the drain hose
Figure 2
Install the two drain hose
fixing hooks taken out into
the installation hole at the
other side of the base frame
(to aim at the installation
hole accurately you can
lean the washing machine
forward slightly).Then rotate
for 90 (As per Figure 4).
Rotate the fixing
hook for 90
Rotate the fixing
hook for 90
to fix it
Takeoff the fixing
hook downwards
Insert the fixing hook into the
installation hole upwards
Figure 4
Figure 3
Pull the fixing hook outwards slightly.
Inlay the drain hose into the fixing hooks
reliably along the groove at spin tub side,
and make it extend towards spin tub side.
Then hang the drain hose into the hanging
hole at the spin tub side. (As per Figure 5).
Figure 5
Extend the drainhose from the rear side
Take out the drain hose from the fixing
hook. Extend it from the rear side (When
the drain hose is extended from the rear
side, it can be hung on the point for drain
hose at the two sides of the cabinet.)
(See to Figure 6).
Figure 6
5
Install the water inlet hose; Select the water level
Insert the water inlet hose into the water-filling
entrance on the control pane directly.(pull it
out to dismantle it)
Water inlet hose
Water inlet
Select water level according to the
quantity of the laundries.
Water level
indicator
Set the water level adjusting lever
to needed line.
Max.
Med
Min
Maximum
Medium
Use the new water inlet hose provided
with the machine to connect to the
water faucet. Old hose sets should
not be reused.
Minimum
Quick water-filling entrance
You can fill water into the wash tub directly
through this entrance. It can reduce the
humidity inside the control panel significantly
Quick water-filling entrance
and prolong the operating life of the components.
Water inlet hose
Insert the water inlet hose into the water-filling
entrance, then push the water-filling jointer into
the quick water- filling entrance. (To dismantle
the water inlet pipe, just push the control handle
as indicated in the figure and pull it out)
Water inlet jointer
Push
Control handle
Quick water-filling entrance
6
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put up the drain hose .
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Check if
The quantity of
When the pulsator
Clear the
Tie the long
strips; fasten
the buttons;
close zippers.
the laundries
has special
requirement
on washing
the laundries is running , the
shall not be too buttons of the
large. Stretch laundries may
and loosen the cause noise. For
laundries before the sake of
pocket. Take
out the coins,
sand, hairpins
etc.
putting them in discretion, please
the tub.
put the laundries
with buttons into
other laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
7
The musts in washing
The capacity of washing and spinning of the
machine refer to the largest weight of the
standard laundries under dry condition that can
be washed or spinned in one time. Laundries
quantity in one washing cycle shall be lower
than the rated capacity.
The thickness ,size , type of the cloth will influ-
ence the actual washing capacity. It is suit-
able to put in reasonable amount of laundries
and the laundries can be turned round in wash-
ing for one time washing.
Do not select " Maximum " water level for
laundries less than 2.4kg, so as to avoid
splashing of water.
It is suggested not to use high sudsing detergent.
Usage of the detergent
How to use the washing powder
How to use the whitener
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30
seconds to dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
Fill water to decided level. Dilute
the whitener with container.
Pour it slowly into the washing tub.
Avoid using whitener on laun-
dries with color or pattern as they
are prone to lose color.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 C and a
container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
The whitener shall not touch
the laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
For powder whitener, please
dissolve it before using.
Dosage of different washing powder is
different. Please refer to the instruction
of the washing powder for the detail
dosage.
8
Washing sequence
Water-filling selector handle
Overfilling sign
Wash timer
Wash selector
Spin timer
Buzzer
(The buzzer will ring when
the washing finishes)
Water-filling entrance
(To set to below 2 minute,
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
(Strong current,
standard current)
first set to
5
minute then
turn it back. it can increase
the service life of the timer).
OFF
OFF
STRONG
STANDARD
OFF
MAX
DRAIN
BUZZER
WASH SELECTOR
WASH TIMER
SPIN TIMER
Wash
WASH SPIN
1.Water-filling selector
(1) Set the water-filling selector at the "WASH" side.
(Figure 1)
(2) Set the water level adjusting lever to needed line.
Figure 1
Figure 2
2. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 2)
Run washing program for some time to stir and
dissolve the powder completely.
STRONG
STANDARD
DRAIN
3.Put in the laundries. If the water quantity is
insufficient, please add water.
WASH SELECTOR
Figure 3
4.Select the current.
Select the strength of the current according to
the laundries. (Figure 3)
OFF
5.Select the washing time
Select the washing time according to the
laundries. (Figure 4)
WASH TIMER
Figure 4
STRONG
STANDARD
6.After washing, the buzzer will ring. Set the "WASH
SELECTOR" at "DRAIN". (Figure 5).
DRAIN
WASH SELECTOR
Figure 5
9
Midway spinning
1.Put the laundries into the spin tub evenly and smoothly.
2.Spin
(1) Put the gland in properly.
Please put in the gland properly even if the
laundries quantity is small.
Push
Gland
Push
Proper
Proper
The laundries
are slanting
No gland
(2) Close the inner and outer cover of the spin tub.
Outer cover of
The spin tub
Inner cover of
The spin tub
(3) Spin for 1-2 minutes.
3.Run the foam-removing spinning.
(1) Open the outer cover of the spin tub.
(2) Set the water-filling selector control
rod at the "SPIN" side. Fill water for
about 1 minute.
WASH SPIN
If the water quantity filled is too large,
the water may flow out from the wash
tub side. Please twist the water tap to
limit the water filling.
(3) Close the outer cover of the spin tub.
Spin for 1-2 minutes.
10
Rinsing
Rinse with water-filling
1.Put the laundries into the wash tub. Select
suitable current according to the laundries.
OVERFLOW
If you find water flo-
wing out here,please
twist the water tap to
limit the water filling.
2.Adjust the water level
Set the water level with water level adjusting
lever according to the laundries quantity.
Then fill suitable water continuously.
3.Rinse
Adjust the wash timer to 5-7 minutes to do
rinsing.
(Repeat the midway spinning and
rinsing with stored water for 2-3 times)
Rinse with stored water
1. Put the laundries into the wash tub. Select suitable current according to
the laundries.
2. Fill water to preset water level.
3. Rinse
Adjust the wash timer to 2-3 minutes to do rinsing.
When the laundries quantity is below 2.4kg, please use "Standard" current.
If you use "Strong" current, it may splash.
11
Spinning
1. Put the laundries into the spin tub
evenly and smoothly.
2. Press the gland in the tub properly.
Close the inner and outer cover of
the spin tub.
3. Spin
Select suitable spin time according
to the laundries, and do spinning.
During spinning, if there's abnormal
sound, it is generally owing to slanting
placement of the laundries. Please
stop the machine and re-order the
laundries.
In spinning, it will pause the work if you open the outer cover of the
spin tub. Close it to resume the spinning.
To do spinning and draining
or rinsing with water-filling
together, please first do
spinning for around 1 minute,
then do draining or rinsing
with water-filling. Otherwise
the spinning will stop owing
to too much water stored in
the spin tub.
12
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter and
overflow filter in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See to
Figure 1)
Figure 1
2. Clean the lint
Put it in water and clean while it is
still wet.(See to Figure 2)
3. Install the lint filter
After cleaning, insert the bottom
Figure 2
of the lint filter ( marked with
"down side") into the overflow filter ,
then push the upper part of the
filter in ( marked with " up side ").
(See to Figure 3)
Figure 3
Cleaning the overflow filter
Too much lint on the overflow filter will influence
the normal usage of the machine. Please
clean it every two months.
Elastic fixing
claw
1
Take off the overflow filter.
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
13
Cleaning the overflow filter
2. Take off the corrugation pipe.
Dismantle the upper part of the
corrugation pipe inside the
overflow filter ( as indicated in
Figure 1).
Water level
adjusting lever
Corrugation
Pipe
3. Cleaning the overflow filter
Clean the lint around the filter
and flush with tap water.
Figure 1
4. Install the overflow filter.
(1).Install the corrugation pipe.
(2).Insert the mounting plate at
the bottom of the filter into
the valve cover.
Hook
(3).Hang up the hook at the left
upper side.
Figure 2
(4).Push the upper part in as
indicated in Figure 2.
Disposal of the complete unit
After washing, dismount the water inlet
hose.
Do not store water in the tub for long
period. Discharge the water immediately
after each using.
Pull off the power plug and hang up the
power cord.
Hang up the drain hose.
Wipe the complete unit with soft
cloth twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
Wipe off the water drops on the surface
and inside the tub with clean soft cloth.
Open the cover of the wash tub and the
inner/outer cover of the spin tub for
some time (about one hour), then close
them.
Petrol
Thinner
Alcohol
14
Trouble-shooting Answer toquestion
If the laundries fall to the outer side of the spin tub
If the laundries fall to the outer side of the spin tub,
please take them out immediately.
1.Dismantle
As indicated in the figure, push the point marked
Spin tub frame
with " " to pull the spin tub frame to oblique
upwards to dismantle it.
2.Install
After install the back edge of the spin tub frame to
proper position, push the four points marked with
"
" by force to reset it.
Please check carefully. The laundries may fall to the
lower part of the outer side of the spin tub (as indicated
in the figure).
Spin tub
If the laundries fall to the outer side of the spin tub, during
spinning the draining will get blocked and the rotation speed
of the spin tub is reduced.
Laundries
When the remained water is frozen
Prevent the freezing (be sure to discharge the water
completely after using)
After complete draining, set the "WASH SELECTOR"
at "STRONG" or "STANDARD". If it is set at "DRAIN",
it will be rather difficult for the frozen water to melt.
Below 50 c
2~3L
When the water is frozen
Pour hot water below 50
into the wash tub
to soak it completely. Then turn the pulsator
with hands gently. Please confirm the drainage
can work normally before next using.
15
Trouble-shooting Answer toquestion
(If there's breakdown, please pull off the power plug before checking)
The following phenomena are not breakdowns sometimes. Please confirm
again before sending it to repair. If there are real breakdowns, please
come to the special maintenance department or after-sale service
department of our company. Do not repair it by yourself.
Phenomena
The reason
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by foreign materials?
The machine does
not act.
Is the drain hose frozen?
The draining does not
work
Is the drain hose blocked by foreign material?
Are there laundries falling to the outer side of
the spin tub?
There's abnormal
sound during washing
Are there hair pin, coins or metal items brought
inside the tub?
Is the machine slanting?
There's abnormal
sound and violent
vibration during
spinning
Is the gland pressed evenly?
Are there laundries falling to the outer side of
the spin tub?
Are the laundries in spin tub too much?
There may be some
water flowing out of
the drain hose in the
first use of the
It is the water remained in the factory inspection
of performance.
machine.
16
Packing list
Quantity
One piece
Name
User's manual
One piece
One piece
Water inlet hose
Lint filter
Water-filling jointer
One piece
One piece
One set
Gland
Twin-tub washing machine
Specification
Water level/Water quantity (about)
Maximum/55L Medium/46L Minimum/36L
Injection pressure(MPa)
0.02~0.2
6.0/6.0
Rated washing /spinning capacity(kg)
17
|