6” BENCH GRINDER
Model 90003
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright 2003 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
3.
4.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
ELECTRICAL SAFETY
Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter
plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should electrically malfunction or
break down, grounding provides a low resistance path to carry electricity away
from the user.
5.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation eliminates the need for the
three wire grounded power cord and grounded power supply system.
6.
Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
7.
8.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the tools
or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,
sharp edges, or moving parts. Replace damaged Power Cords immedi-
ately. Damaged Power Cords increase the risk of electric shock.
9.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
PERSONAL SAFETY
10.
Stay alert. Watch what you are doing, and use common sense when oper-
ating a power tool. Do not use a power tool while tired or under the influ-
ence of drugs, alcohol, or medication. A moment of inattention while operat-
ing power tools may result in serious personal injury.
SKU 90003
PAGE 3
11.
12.
13.
14.
15.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure the Power Switch is off before plugging
in. Carrying power tools with your finger on the Power Switch, or plugging in
power tools with the Power Switch on, invites accidents.
Remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected
situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
TOOL USE AND CARE
16.
Use clamps (not included) or other practical ways to secure and support
the workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
17.
18.
Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must
be replaced.
19.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
20.
21.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with a sharp cutting edge are less likely to bind and are easier
to control. Do not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
SKU 90003
PAGE 4
22.
23.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have
the tool serviced before using. Many accidents are caused by poorly main-
tained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SERVICE
24.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
25.
When servicing a tool, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
1.
Maintain a safe working environment. Keep the work area well lit. Make sure
there is adequate surrounding workspace. Always keep the work area free of
obstructions, grease, oil, trash, and other debris. Do not use the Bench Grinder
in areas near flammable chemicals, dusts, and vapors.
2.
3.
4.
5.
Maintain labels and nameplates on the Bench Grinder. These carry
important information. If unreadable or missing, contact Harbor Freight Tools for
a replacement.
WARNING! To avoid serious personal injury and/or property damage,
always use Grinding Wheels (part #64) that are rated at 3450 RPM or
greater on this particular Bench Grinder.
Replace a cracked, broken, or excessively worn Grinding Wheel (part #64)
immediately. Use only the flanges furnished with the Bench Grinder. Do
not overtighten the wheel nut.
Always wear a safety impact full face shield, hearing protection, and heavy
duty work gloves when using this product. A safety impact full face shield,
hearing protection, and heavy duty work gloves are available from Harbor Freight
Tools.
6.
Keep all guards in place and working properly.
SKU 90003
PAGE 5
7.
Always maintain a 1/16” distance or less between the Grinding Wheels
(part #64) and Left and Right Tool Rests (parts #28, #32) as the diameter of
the Grinding Wheels decrease with use.
8.
To avoid accidental electrical shock, do not allow the Power Switch
(part #3) to become wet. Do not touch the Power Switch with wet hands.
9.
When using the Bench Grinder, always maintain a firm grip on the object
being ground with both hands.
10.
To avoid accidental burns use caution when handling an object that is
being ground. Allow sufficient time for the object to completely cool before
handling.
11.
12.
Always remove all adjusting keys and wrenches from the Bench Grinder
before starting.
Do not pull or carry the Bench Grinder by its Power Cord (part #4), or
pull the Cord around sharp corners or edges. Do not unplug the Bench
Grinder by pulling on the Cord. Keep the Cord away from heated surfaces.
13.
14.
15.
Do not force the tool. This Bench Grinder will do the work better and safer at
the speed and capacity for which it is designed.
Keep fingers and hands as far away as possible from the rotating Grinding
Wheels (part #64).
Check for damaged parts. Before using this product, carefully check that it will
operate properly and perform its intended function. Check for damaged parts
and any other conditions that may affect the safe operation of this product.
Replace or repair damaged or worn parts immediately.
16.
Replacement parts and accessories. When servicing, use only identical re-
placement parts. Only use accessories intended for use with this product.
17.
Use the right product for the right job. There are certain applications for
which this product was designed. Do not use small equipment, tools, or attach-
ments to do the work of larger industrial equipment, tools, or attachments. Do
not use this product for a purpose for which it was not intended.
18.
Stay alert. Watch what you are doing at all times. Use common sense. Do
not use this product when you are tired or distracted from the job at hand.
19.
Do not operate this product when fatigued or under the influence of alcohol
or drugs.
SKU 90003
PAGE 6
22.
23.
Always turn off the Bench Grinder and unplug it from its electrical
outlet before changing accessories or performing any inspection, mainte-
nance, or cleaning procedures.
WARNING! The warnings and cautions discussed in this manual cannot
cover all possible conditions and situations that may occur. It must be under
stood by the operator that common sense and caution are factors which cannot
be built into this product, but must be supplied the the operator.
24.
WARNING! Some dust created by power sanding, sawing, grinding, drill-
ing, and other construction activities contain chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are: lead from lead-based paints, crystalline silica
from bricks and cement and other masonry products, arsenic and chromium from
chemically treated lumber. Your risk from these exposures varies depending on
how often you do this type of work. To reduce your exposure to these chemicals
work in a well ventilated area, and work with approved safety equipment such as
those dust masks that are specially designed to filter out microscopic particles.
(California Health & Safety Code 25249.5 et seq.)
25.
WARNING! People with pacemakers should consult their physician(s)
before using this product. Operation of electrical equipment in close proximity to
a heart pacemaker could cause interference or failure of the pacemaker.
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric
shock. Check with a qualfified electrician if you are in doubt as to whether the
outlet is properly grounded. Do not modify the power cord plug provided with
the tool. Never remove the grounding prong from the plug. Do not use the
tool if the power cord or plug is damaged. If damaged, have it repaired by
a service facility before use. If the plug will not fit the outlet, have a proper
outlet installed by a qualified electrician.
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS
1.
Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity aways from the user, reducing the risk of
electric shock. (See Figure A, next page.)
SKU 90003
PAGE 7
2.
3.
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached
to an electrically “live” terminal. (See Figure A.)
Your tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like that in the following illustration. (See Figure A.)
FIGURE A
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS
4.
Tools marked “Double Insulated”
do not require grounding. They have a
special double insulation system which satisfies OSHA requirements and com
plies with the applicable standards of Underwriters Laboratories, Inc., the
Canadian Standard Association, and the National Electrical Code.
(See Figure B.)
5.
Double insulated tools may be used in either of the 120 volt outlets shown in the
following illustration. (See Figure B.)
FIGURE B
SKU 90003
PAGE 8
EXTENSION CORDS
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools
can use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Figure C, next page.)
3.
4.
5.
The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure C.)
When using more than one extension cord to make up the total length, make
sure each cord contains at least the minimum wire size required.
(See Figure C.)
If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Figure C.)
6.
If you are using an extension cord outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
7.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it. Protect your extension cords from sharp objects,
excessive heat, and damp or wet areas.
ꢋꢌꢍꢎꢏꢏꢌꢐꢃꢌꢃꢑꢏꢀꢐꢀꢏꢒꢏꢑꢓꢀꢋꢌꢑꢔꢕꢒꢔꢌꢑꢖꢎꢋꢑꢌꢗꢘꢌꢐꢙꢀꢎꢐꢑꢍꢎꢋꢃꢙꢚ
ꢑꢛꢜꢝ"ꢑ$ꢎ%ꢘ&
ꢐꢕꢏꢌ'%ꢕꢘꢌ
ꢕꢏ'ꢌꢋꢌꢙ
ꢌꢗꢘꢌꢐꢙꢀꢎꢐꢑꢍꢎꢋꢃꢑ%ꢌꢐꢔꢘ<
ꢝ=
ꢖꢂꢂꢁ
ꢜJ
="
ꢖꢂꢂꢁ
ꢜJ
>=
ꢖꢂꢂꢁ
ꢜJ
ꢜJ
ꢜQ
ꢜ[
ꢜꢝ
ꢜ"
\
ꢜ""
ꢖꢂꢂꢁ
ꢜJ
ꢜQ
ꢜ[
ꢜꢝ
ꢜ"
\
ꢜ="
ꢖꢂꢂꢁ
ꢜQ
ꢜ[
ꢜꢝ
ꢜꢝ
\
"ꢑ2ꢑꢝ@"
ꢝ@ꢜꢑ2ꢑZ@[
ꢜJ
ꢜJ
ꢜJ
ꢜJ
Z@=ꢑ2ꢑ=@"
=@ꢜꢑ2ꢑ>@"
ꢜJ
ꢜJ
ꢜQ
ꢜ[
>@ꢜꢑ2ꢑꢜꢝ@"
ꢜꢝ@ꢜꢑ2ꢑꢜQ@"
ꢜQ@ꢜꢑ2ꢑꢝ"@"
ꢜ[
ꢜꢝ
\
ꢜꢝ
ꢜ"
\
\
ꢚꢑ]7ꢄꢂ;ꢑꢉꢊꢑꢟꢇ ꢇꢁꢇꢊꢠꢑꢁꢡꢂꢑꢟꢇꢊꢂꢑꢢꢉꢟꢁ7ꢠꢂꢑ;ꢆꢉꢈ
ꢁꢉꢑꢣꢇꢢꢂꢑꢢꢉꢟꢁꢄꢑ7ꢁꢑꢜ="|ꢑꢉꢣꢑꢁꢡꢂꢑꢆ7ꢁꢂ;ꢑ7 ꢈꢂꢆꢂꢄ@
FIGURE C
SKU 90003
PAGE 9
SYMBOLOGY
Double Insulated
Canadian Standards
Association
Underwriters
Laboratories, Inc.
Volts Alternating Current
V ~
A
xxxx/min.
Amperes
No Load Revolutions
per Minute (RPM)
n
o
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on page 15
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
ASSEMBLY INSTRUCTIONS
NOTE: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram on page 16.
1.
WARNING! Always make sure the Power Plug (part #10) of the Bench
Grinder is unplugged from its electrical outlet prior to assembly, adding any
accessories, or making any adjustments to the tool.
To Attach The Tool Rests:
1.
2.
Align the mounting slot in the Left Tool Rest (part #28) with the two threaded
mounting holes in the Left Wheel Guard (part #27). Insert two Screws with two
Lock Washers (part #25) through the mounting slot in the Left Tool Rest, and
loosely finger tighten the two Screws into the threaded mounting holes in the Left
Wheel Guard. (See Figure D, next page.)
Slide the Left Tool Rest (part #28) forward to within 1/16” of the Grinding Wheel
(part #64). Then, firmly tighten the two Screws with Lockwashers (part #25) to
secure the Left Tool Rest in place. (See Figure D.)
SKU 90003
PAGE 10
3.
Repeat Steps #1 and #2 to attach the Right Tool Rest (part #32) to the Right
Wheel Guard (part #31). (See Figure D.)
SCREW
WITH
LOCK WASHER
(#25)
LEFT WHEEL
GUARD
(#27)
RIGHT WHEEL
GUARD
(#31)
LEFT TOOL
REST
(#28)
RIGHT TOOL
REST
(#32)
FIGURE D
To Attach The Spark Guards:
1.
Align the mounting slot in the Left Spark Guard (part #62) with the threaded
mounting hole in the Left Wheel Guard (#27). Insert one Screw (part #59) with
one Washer (part #60) through the mounting slot in the Left Spark Guard, and
loosely finger tighten the Screw into the threaded mounting hole in the Left
Wheel Guard. (See Figure E.)
2.
3.
Slide the Left Spark Guard (part #62) forward to within 1/16” of the Grinding
Wheel (part #64). Then, firmly tighten the Screw (part #59) with Washer
(part #60) to secure the Left Spark Guard in place. (See Figure E.)
Repeat Steps #1 and #2 to attach the Right Spark Guard (part #61) to the Right
Wheel Guard (part #31). (See Figure E.)
LEFT SPARK GUARD (#62)
LEFT
RIGHT SPARK GUARD (#61)
RIGHT
WHEEL
GUARD
(#31)
WHEEL
GUARD
(#27)
SCREW (#59)
WASHER (#60)
FIGURE E
SKU 90003
PAGE 11
To Attach The Eye Shield Mounting Rods:
1.
Insert one Screw (part #48) with a Washer (part #13) through a Bracket
(part #36) and the Left Eye Shield Mounting Rod (part #49). Then, firmly tighten
the Screw to secure the Left Eye Shield Mounting Rod to the body of the Bench
Grinder. (See Figure F.)
2.
Repeat Step #1 to attach the Right Eye Shield Mounting Rod (part #33) to the
body of the Bench Grinder. (See Figure F.)
BRACKET (#36)
WASHER (#13)
SCREW (#48)
BRACKET (#36)
WASHER (#13)
RIGHT EYE
SHIELD
MOUNTING
ROD
SCREW (#48)
LEFT EYE
SHIELD
MOUNTING
ROD
(#33)
(#49)
FIGURE F
To Attach The Eye Shields:
1.
Loosen the Screw (part #55) on the Pressure Plate (part #50). Slide the Pres-
sure Plate onto the Left Eye Shield Mounting Rod (part #49). Then, re-tighten
the Screw so that the Eye Shield (part #26) can be moved up or down but will be
tight enough to stay in place. (See Figure G, next page.)
2.
Repeat Step #1 to attach the remaining Eye Shield to the Right Eye Shield
Mounting Rod (part #33). (See Figure G.)
To Mount The Bench Grinder On A Workbench:
1.
WARNING! Make sure the workbench (not included) to which the Bench
Grinder will be mounted is flat, level, and sturdy enough to bear the weight of the
Bench Grinder and other tools and materials being used.
SKU 90003
PAGE 12
EYE SHIELD (#26)
PRESSURE PLATE
(#50)
EYE SHIELD (#26)
PRESSURE PLATE
(#50)
LEFT EYE SHIELD
MOUNTING ROD
(#49)
RIGHT EYE SHIELD
MOUNTING ROD
(#33)
SCREW
(#55)
SCREW
(#55)
FIGURE G
2.
3.
There are two 11/32” diameter mounting holes located on the Base (part #15) of
the Bench Grinder. (See Figure H.)
Temporarily set the Bench Grinder in the desired location on the workbench. Use
the two 11/32” diameter mounting holes on the Bench Grinder as templates to
mark where two 11/32” diameter holes will be drilled through the top of the work-
bench. Once marked, remove the Bench Grinder.
4.
Where previously marked, drill the two 11/32” holes through the top of the work-
bench.
5.
Set the Bench Grinder back on the workbench, and align the two mounting holes
on the Bench Grinder with the two previously drilled holes in the workbench.
Then secure the Bench Grinder to the workbench, using two 11/32” diameter
Bolts of appropriate length, two Lock Washers, and two Nuts (none included).
EYE SHIELD
(#26)
EYE SHIELD
(#26)
GRINDING WHEEL
(#64)
GRINDING WHEEL
(#64)
LEFT
TOOL REST
(#28)
RIGHT
TOOL REST
(#32)
11/32” MOUNTING HOLE
11/32” MOUNTING HOLE
POWER SWITCH (#3)
FIGURE H
SKU 90003
PAGE 13
OPERATING INSTRUCTIONS
1.
2.
WARNING! Prior to using the Bench Grinder, make sure to wear ANSI approved
safety glasses, full face safety impact shield, and heavy duty work gloves. Also,
always adjust the two Eye Shields (part #26) directly in line between your eyes
and the object being ground. (See Figure H.) Always keep wheel covers in
place when using the Bench Grinder.
Plug the Power Cord Plug (part #10) into the nearest grounded, 120 volt, electri-
cal outlet. Then, turn the Power Switch (part #3) to its “ON” position and allow
the Grinding Wheels (part #64) to spin up to full speed. (See Figure H.)
3.
4.
Hold the workpiece being ground with both hands, taking care to keep fingers
and hands away from the spinning Grinding Wheels (part #64). (See Figure H.)
Place the workpiece on the Left or Right Tool Rest (parts #28, #32), applying
moderate pressure on the workpiece and keeping it moving to the left and right at
an even pace for smooth grinding. NOTE: Feeding the workpiece too hard into
the Grinding Wheel (part #64) can overheat the Motor and prematurely wear
down the Grinding Wheel. (See Figure H.)
5.
IMPORTANT: Keep a tray nearby filled with water, and dip the workpiece into the
water regularly to prevent overheating. Overheating can weaken metals.
6.
Once the grinding job is completed, turn the Power Switch (part #3) to its “OFF”
position and allow the Grinding Wheels (part #64) to stop on their own. Unplug
the Bench Grinder when it is not in use. (See Figure H.)
7.
Place the workpiece in the tray of water and allow the workpiece to completely
cool before handling.
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
WARNING! Make sure the Power Switch (part #3) of the Bench Grinder is
in its “OFF” position and that the tool is unplugged from its electrical outlet be-
fore performing any inspection, maintenance, or cleaning procedures.
BEFORE EACH USE, inspect the general condition of the Bench Grinder.
Check for loose screws, misalignment or binding of moving parts, damaged
electrical wiring, cracked, chipped, or damaged Grinding Wheels (part #64), and
any other condition that may affect its safe operation. If abnormal noise or vibra-
tion occurs, have the problem corrected before further use.
Do not use damaged equipment.
SKU 90003
PAGE 14
3.
TO CLEAN: Use vaccum or a clean cloth and mild detergent to clean the body of
the Bench Grinder. Do not use solvents. Do not immerse any part of the tool in
liquid.
PARTS LIST
'7ꢆꢁꢑ
ꢍ
ꢎ
"
#
$
ꢓ
ꢚ
ꢃꢂꢄꢅꢆꢇꢈꢁꢇꢉꢊ
ꢈꢠꢄꢠꢅ
ꢗꢄꢇꢄꢠꢅ
ꢖꢠꢡꢂꢅꢐꢗꢡꢆꢄꢃꢙ
ꢖꢠꢡꢂꢅꢐ*ꢠꢅ+
€ꢁꢤ@
ꢍ
'7ꢆꢁꢑ
""
"#
"$
"ꢓ
"ꢚ
"<
"`
#ꢏ
#ꢍ
#ꢎ
#"
##
#$
#ꢓ
#ꢚ
#<
#`
$ꢏ
$ꢍ
$ꢎ
$"
$#
$$
$ꢓ
$ꢚ
$<
$`
ꢓꢏ
ꢓꢍ
ꢓꢎ
ꢓ"
ꢓ#
ꢃꢂꢄꢅꢆꢇꢈꢁꢇꢉꢊ
ꢈꢆꢘꢙꢄꢐꢀꢣꢂꢐꢗꢙꢆꢂꢁ+ꢐ%ꢠꢊꢋꢄꢆꢋꢘꢐꢈꢠ+
/ꢇꢌꢂꢐꢖꢁꢇꢄꢂ
ꢈꢊ^^ꢂꢅꢐ'ꢠꢠꢄ
/ꢅꢇꢃꢜꢂꢄ
€ꢁꢤ@
ꢍ
ꢍ
#
ꢎ
ꢍ
"
ꢎ
ꢎ
ꢍ
ꢍ
ꢍ
ꢍ
"
ꢎ
#
#
ꢍ
ꢎ
#
#
ꢎ
ꢎ
ꢎ
#
#
ꢎ
#
#
ꢍ
ꢍ
ꢎ
ꢎ
ꢍ
ꢍ
ꢎ
ꢎ
ꢍ
ꢍ
ꢍ
ꢍ
ꢍ
ꢍ
#
#
ꢍ
ꢍ
#
ꢍ
ꢎ
ꢍ
<
<
ꢍ
ꢍ
#
ꢓ
ꢎ
ꢍ
ꢍ
ꢍ
ꢍ
ꢍ
ꢍ
*ꢇꢞꢇꢃꢆꢄꢠꢅ
5ꢆꢅꢂꢐ_ꢊꢄ
ꢗꢡꢆꢄꢃꢙꢐꢖꢁꢇꢄꢂ
_ꢇ ꢂꢞꢁꢇꢄꢂ
7ꢂꢅ ꢆꢋꢇꢁ{ꢐ*ꢇꢞꢇꢃꢆꢄꢠꢅ
7ꢂꢅ ꢆꢋꢇꢁ{ꢐꢗꢡꢆꢄꢃꢙ
|ꢅꢠꢊꢋ+ꢐ7ꢂꢅ ꢆꢋꢇꢁ
'ꢁꢇꢄꢐ5ꢇꢌꢙꢂꢅ
=ꢠꢃꢜꢐ5ꢇꢌꢙꢂꢅ
ꢗꢃꢅꢂꢡ
<
`
ꢍꢏ
ꢍꢍ
ꢍꢎ
ꢍ"
ꢍ#
ꢍ$
ꢍꢓ
ꢍꢚ
ꢍ<
ꢍ`
ꢎꢏ
ꢎꢍ
ꢎꢎ
ꢎ"
ꢎ#
ꢎ$
ꢎꢓ
ꢎꢚ
ꢎ<
ꢎ`
"ꢏ
"ꢍ
"ꢎ
ꢗꢃꢅꢂꢡ
5ꢇꢌꢙꢂꢅ
*ꢠꢅ+ꢐ/ꢊꢌꢙꢆꢋꢘꢐꢖꢁꢇꢄꢂ
/ꢇꢌꢂ
ꢗꢃꢅꢂꢡ
ꢗꢃꢅꢂꢡ
'ꢁꢇꢄꢐ5ꢇꢌꢙꢂꢅ
ꢗꢃꢅꢂꢡ{ꢐ'ꢠꢠꢄ
=ꢂꢤꢄꢐꢀꢣꢂꢐꢗꢙꢆꢂꢁ+ꢐ%ꢠꢊꢋꢄꢆꢋꢘꢐꢈꢠ+
ꢖꢅꢂꢌꢌꢊꢅꢂꢐꢖꢁꢇꢄꢂ
ꢗꢃꢅꢂꢡ
=ꢠꢃꢜꢐ5ꢇꢌꢙꢂꢅ
ꢀꢋ+ꢐ/ꢂꢁꢁ
ꢗꢃꢅꢂꢡ{ꢐꢀꢋ+ꢐ/ꢂꢁꢁ
=ꢠꢃꢜꢐ5ꢇꢌꢙꢂꢅ
=ꢂꢤꢄꢐ5ꢙꢂꢂꢁꢐ*ꢠꢢꢂꢅ
=ꢂꢤꢄꢐꢔꢇꢋ+ꢐ*ꢁꢇ ꢞꢐ_ꢊꢄ
*ꢁꢇ ꢞꢐ5ꢇꢌꢙꢂꢅ
ꢗꢃꢅꢂꢡ{ꢐ=ꢠꢃꢜꢐ5ꢇꢌꢙꢂꢅ
ꢀꢣꢂꢐꢗꢙꢆꢂꢁ+
=ꢂꢤꢄꢐ5ꢙꢂꢂꢁꢐ|ꢊꢇꢅ+
=ꢂꢤꢄꢐ7ꢠꢠꢁꢐꢈꢂꢌꢄ
ꢈꢆꢘꢙꢄꢐ5ꢙꢂꢂꢁꢐ*ꢠꢢꢂꢅ
ꢈꢆꢘꢙꢄꢐꢔꢇꢋ+ꢐ*ꢁꢇ ꢞꢐ_ꢊꢄ
ꢈꢆꢘꢙꢄꢐ5ꢙꢂꢂꢁꢐ|ꢊꢇꢅ+
ꢈꢆꢘꢙꢄꢐ7ꢠꢠꢁꢐꢈꢂꢌꢄ
_ꢊꢄ
=ꢠꢃꢜꢐ5ꢇꢌꢙꢂꢅ
5ꢇꢌꢙꢂꢅ
ꢗꢃꢅꢂꢡ
5ꢇꢌꢙꢂꢅ
=ꢠꢃꢜꢐ5ꢇꢌꢙꢂꢅ
_ꢊꢄ
ꢗꢃꢅꢂꢡ
5ꢇꢌꢙꢂꢅ
ꢈꢆꢘꢙꢄꢐꢗꢞꢇꢅꢜꢐ|ꢊꢇꢅ+
=ꢂꢤꢄꢐꢗꢞꢇꢅꢜꢐ|ꢊꢇꢅ+
ꢈꢠꢄꢇꢄꢆꢠꢋꢐ=ꢇ^ꢂꢁ
|ꢅꢆꢋ+ꢆꢋꢘꢐ5ꢙꢂꢂꢁ
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 90003
PAGE 15
ASSEMBLY DIAGRAM
58
26
33
57
58
13
36
26
52
53
51
62
48
13
50
54
61
54
53
52
59,60
59
29
46
48
36
1
50
51
60
28
30
63
24
55
64
12
55
13
56
57
50
5
63
31
32
27
24
40
25
25
19
20
21
18
23
25
18
24
20
22
12
13
9
17
5
16
2
37
45
15
7
40
39
4
44
14
41
3
38
6
8
10
44,45
35
47
42
43
44
45
48
34
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTUER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLA-
TION OF REPLACEMENT PARTS THERETO.
SKU 90003
PAGE 16
|