Hunter Fan Outdoor Ceiling Fan 41449 01 05 00 User Manual

INSTALLATION INSTRUCTIONS FOR  
HUNTER CEILING FAN LIGHT KIT  
FLUSH MOUNT STYLE  
READ AND SAVE THESE INSTRUCTIONS  
CAUTION:  
1. Read entire instructions carefully before beginning installation.  
2. To avoid possible shock, be certain electricity is shut OFF at  
main panel before wiring.  
Fan Switch Housing  
3. All wiring must be in accordance with national and local elec-  
trical code.  
4. Professional installation recommended.  
FIGURE 4  
Pre In st a lla t io n Pre p a ra t io n  
Light Kit  
Unscrew the decorative finial on the light kit by turning it counter  
clockwise. Slide it off over the pull cord, removing the keeper on  
the end of the cord only if necessary. Remove the light kit cover  
plate. See Figure 1.  
FIGURE 1  
Screws  
Decorative Finial  
Feed the pull cord back through the light kit cover and the decora-  
tive finial. Center the light kit cover on the threaded nipple, mak-  
ing sure no wires are caught or in the way. Thread the decorative  
finial onto the threaded nipple and hand tighten. Re-install the  
cord keeper if it was removed previously.  
Light Kit Cover Plate  
Pull Cord  
Remove the cover plate from the fan switch housing.  
In st a llin g Glo b e s a n d Bu lb s  
Place globe over threaded lampholder in cup. Install and hand  
tighten threaded locking ring on lampholder as shown in figures 5  
and 6  
Note: Do not discard the switch housing cover plate. You will  
need to replace it if you remove the light fixture in the future.  
Wire t h e Lig h t Kit  
CAUTION: This appliance must be earthed.  
Install bulbs. Use E-27 bulb, no smaller than A-19 (60mm diam-  
eter). Turn power ON at main panel.  
Locate the two wires in the fan switch housing that have connectors  
attached. Pull the plugs out of both connectors. Connect the black  
and white wire to the brown wire of the light kit. Connect the blue  
wire to the blue wire of the light kit. Be sure to connect the green  
Cup  
FIGURE 5  
Threaded  
and yellow ground wire to the screw marked  
base of the switch housing. See Figure 2.  
located at the  
Lamp  
Holder  
Co m p le t e t h e Asse m b ly  
Attach the light kit to the fan switch housing using the screws  
provided, leaving screws slightly loose temporarily. Make sure all  
wires fit flush inside the switch housing. See Figures 3 and 4 .  
Threaded  
Locking Ring  
Globe  
Rotate the light kit counter clockwise as seen from below, until it  
stops, so the screws are lined up in the narrow notches in the mount-  
ing holes. See Figure 3 Tighten the screws securely.  
Note: As shown in Figure 6, line up the beginning of the first  
thread on the lamp holder and notch on the locking ring to  
avoid cross threading the ring. If ring becomes hard to turn,  
rotate ring counter clockwise to loosen and reposition. Do  
not force the ring on.  
FAN SWITCH  
HOUSING  
GROUND  
SCREW  
FIGURE 6  
Beginning of  
First Thread  
Threaded  
Locking Ring  
FIGURE 2  
Notch in Ring  
HUNTER FAN COMPANY  
2500 FRISCO AVENUE  
MEMPHIS, TN 38114  
FIGURE 3  
41449-01 05/00  
©2000 HUNTER FAN CO  
 

Harbor Freight Tools Impact Driver 95666 User Manual
Hasbro Robotics 82993 User Manual
Honeywell Automobile HCM 3060 User Manual
Honeywell Photo Scanner 1902 User Manual
Hotpoint Refrigerator FF47MX User Manual
Hotpoint Washer WM33 User Manual
HP Hewlett Packard Scanner Scanjet 5370 User Manual
Husqvarna Microwave Oven Built in Oven User Manual
IBM Laptop T40 User Manual
Igloo Beverage Dispenser FRW152 User Manual