Haier Washer HWM80 113S Fiji User Manual

Twin-tub Washing Machine  
User's manual  
This manual is for  
HWM80-113S-Fiji  
Please read this manual  
carefully before using.  
Retain it foDrofwuntuloraed rfreofmerWewnwc.eS.omanuals.com. All Manuals Search And Download.  
Names of the parts  
Buzzer  
Water-filling entrance  
Water inlet selector handle  
Wash selector  
Outer cover of the spin tub  
Inner cover of the spin tub  
Spin timer  
Wash timer  
Spin tub frame  
Control panel  
Spin tub  
Overflow filter  
Quick water-filling entrance  
Drain hose hook  
Water level adjusting lever  
Lint filter(Installed by user)  
Pulsator  
Cabinet  
Wash tub  
Drain hose  
Base frame  
Meaning and description of the symbols  
Contents marked with that symbol are related  
to the safety of the product and the personal  
safety of the users. Please operate in strict  
conformity to the contents, otherwise it may  
cause damage of the machine or injure the  
personal safety of the user.  
Warning sign  
Contents marked with that symbol are actions  
forbidden to perform. Performing of those  
actions may result in damage of the machine  
or injure the personal safety of the user.  
Forbidding sign  
Please check if the power receptacle has good earthing  
condition before using to guarantee your safety.  
 
1
Safety precautions  
Please insert the power cord into  
special receptacle with rated vol-  
tage.Be sure to use single-phase  
three pins receptacle.The earthing  
terminal of the receptacle must be  
earthed reliably.If possible,please  
adopt electric leakage protector.  
When the machine is normally  
using, please put the power plug  
at the location easily to be insert-  
ed and extracted by hand. Be sure  
to pull the plug off when there's  
power failure, or the machine is  
being moved, cleaned or when it  
is idle.  
Earth  
If the power cord is bad, to avoid risk it is required to replace it by the  
technicians ofour special shop or the after-sale service department.  
Keep the pin of the power plug clean.  
Do not use water hotter than 65 C .  
Do not put the machine at damp  
place like the bathroom . Never  
wash it with water. Do not place  
wet laundries on the control panel.  
For washing machine with ventilation  
openings in the base, that a carpet  
must not obstruct the openings.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Ventilation hole at  
the bottom of the  
washing machine  
Do not let the machine share one receptacle  
with other electric appliances. If the power  
plug is damaged, or the plugging into the  
receptacle is loose, do not use the plug any  
more.  
2
 
Safety precautions  
Do not stretch hands into the working  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children.  
Do not decompose, repair or alter the  
machine by yourself.  
Do not put any hot or heavy items  
( such as the kettle with hot water )  
on the washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.).  
l
ro  
et  
er  
P
inn  
Th  
Keep the machine away from direct  
sunlight and heat source like the  
heater.  
Handicapped or children without care  
shall not use the machine.  
To protect your laundries and wash-  
ing machine, please take out all of the  
coins, buttons, sand, hairpin and  
other foreign materials before washing.  
Please check if the water faucet is open,  
and if the connection of the water inlet  
pipe is proper.  
It is suggested to use foamless washing  
powder.  
 
3
Installation and adjustment  
Please install and adjust the machine according to the requirement of  
the manual. It is very important to your security and correct operating  
the machine.  
Install the lint filter  
After opening the package,please take out the lint  
filter from the document bag,install it to the overflow  
filter of the wash tub.See to the figure.  
Overflow filter  
Lint filter  
Usage of the drain hose  
Before using , hang up the drain hose on suitable location.  
Do not put down the drain hose on the ground.  
<1.2m  
Confirm the end of drain hose is higher than  
the level of tub . If not the siphon will being .  
4
 
How to change the direction of the drain hoses  
Side sectional view  
Figure 1 indicates the ex factory  
installation position of the drain  
hose.  
Drain hose  
fixing hook  
Fixing hook  
installation hole  
Figure 1  
Drain hose  
Pull outwards  
slightly  
Extend the drain hose from the side of spin tub.  
Take off  
the drain hose  
Take off the drain hose from the hanging  
hole of the cabinet. Pull the drain hose  
fixing hook outwards gently to take out  
the drain hose from the two fixing hooks.  
(As per Figure 2)  
Drain hose  
fixing hook  
Figure 2  
Rotate the drain hose fixing hook for 90  
to take it out from the installation hole  
(As per Figure 3).  
Rotate the fixing  
hook for 90  
Rotate the fixing  
hook for 90  
to fix it  
Install the two drain hose  
fixing hooks taken out into  
the installation hole at the  
other side of the base frame  
(to aim at the installation  
hole accurately you can  
lean the washing machine  
forward slightly).Then rotate  
for 90 (As per Figure 4).  
Take off the fixing  
hook downwards  
Insert the fixing hook into the  
installation hole upwards  
Figure 4  
Figure 3  
Pull the fixing hook outwards slightly.  
Inlay the drain hose into the fixing hooks  
reliably along the groove at spin tub side,  
and make it extend towards spin tub side.  
Figure 5  
Figure 6  
Extend the drain hose from the rear side  
Take out the drain hose from the fixing hook. Extend it from the rear side (When  
the drain hose is extended from the rear side, it can be hung on the point for drain  
hose at the two sides of the cabinet.) (See to Figure 6).  
 
5
Install the water inlet hose; Select the water level  
Insert the water inlet hose into the water-filling  
entrance on the control pane directly.(pull it  
out to dismantle it)  
Water inlet hose  
Water inlet  
Select water level according to the  
quantity of the laundries.  
Water level  
indicator  
Set the water level adjusting lever  
to needed line.  
Max.  
Med  
Min  
Maximum  
Medium  
Use the new water inlet hose provided  
with the machine to connect to the  
water faucet.Old hose sets should  
not be reused.  
Minimum  
Quick water-filling entrance  
Quick water-filling entrance  
You can fill water into the wash tub directly  
through this entrance. It can reduce the  
humidity inside the control panel significantly  
and prolong the operating life of the components.  
Water inlet hose  
Insert the water inlet hose into the water-filling  
entrance, then push the water-filling jointer into  
the quick water- filling entrance. (To dismantle  
the water inlet pipe, just push the control handle  
as indicated in the figure and pull it out)  
Water inlet jointer  
Push  
Control handle  
Quick water-filling entrance  
 
6
Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose.  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose .  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
Pay attention to followings before washing the laundries  
Check if  
The quantity of  
When the pulsator  
Clear the  
Tie the long  
strips; fasten  
the buttons;  
close zippers.  
the laundries  
has special  
requirement  
on washing  
the laundries is running , the  
shall not be too buttons of the  
large. Stretch laundries may  
and loosen the cause noise. For  
laundries before the sake of  
pocket. Take  
out the coins,  
sand, hairpins  
etc.  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like  
mud or dust. For the parts with heavy soil, please apply detergent on  
them in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn  
it over before putting in.  
f. Do not put those laundries polluted by chemicals into the washing  
machine directly.  
7
 
The musts in washing  
The capacity of washing and spinning of the  
machine refer to the largest weight of the  
standard laundries under dry condition that can  
be washed or spinned in one time. Laundries  
quantity in one washing cycle shall be lower  
than the rated capacity. The largest capacity  
of this machine is 7.1 kg.  
The thickness ,size , type of the cloth will influ-  
ence the actual washing capacity. It is suit-  
able to put in reasonable amount of laundries  
and the laundries can be turned round in wash-  
ing for one time washing.  
Do not select " Max " water level for  
laundries less than 2.4kg, so as to avoid  
splashing of water.  
It is suggested not to use high sudsing detergent.  
Usage of the detergent  
How to use the whitener  
How to use the washing powder  
Direct dissolved in the machine:  
1.Fill small quantity of water.  
2.Add the powder . Run for 30  
seconds to dissolve it completely.  
3.Put it in the laundries. Select suitable  
water level.  
Fill water to decided level. Dilute  
the whitener with container.  
Pour it slowly into the washing tub.  
Avoid using whitener on laun-  
dries with color or pattern as they  
are prone to lose color.  
The instant dissolving of the washing  
powder:  
1.Prepare warm water of 30 C and a  
container.  
2.Add the powder while stirring to fully  
dissolve it.  
The powder is more prone to pollute the  
laundries than the detergent. Therefore  
please use it with proper quantity.  
The whitener shall not touch  
the laundries directly.  
Refer to the user's manual for  
the usage and quantity of the  
whitener.  
For powder whitener, please  
dissolve it before using.  
Dosage of different washing powder is  
different. Please refer to the instruction  
of the washing powder for the detail  
dosage.  
8
 
Washing sequence  
Water-filling selector handle  
Overfilling sign  
Spin timer  
Buzzer  
(The buzzer will ring when  
the washing finishes)  
Wash timer  
(To set to below 2 minute,  
Wash selector  
(Strong current,  
standard current)  
Water-filling entrance  
(To set to below 1 minute,  
first set to 2 minute then  
turn it back. It can increase  
the service life of the timer).  
first set to  
5
minute then  
turn it back. it can increase  
the service life of the timer).  
OFF  
OFF  
STRONG  
STANDARD  
OFF  
MAX  
KPB70-113S-P  
DRAIN  
BUZZER  
WASH SELECTOR  
WASH TIMER  
SPIN TIMER  
Wash  
WASH SPIN  
1.Water-filling selector  
(1) Set the water-filling selector at the "WASH" side.  
(Figure 1)  
(2) Set the water level adjusting lever to needed line.  
Figure 1  
2. Fill the water and add the dissolved washing  
powder to make the water level reach the preset  
position. (Figure 2)  
Run washing program for some time to stir and  
dissolve the powder completely.  
Figure 2  
STRONG  
STANDARD  
3.Put in the laundries. If the water quantity is  
insufficient, please add water.  
DRAIN  
WASH SELECTOR  
Figure 3  
4.Select the current.  
Select the strength of the current according to  
the laundries. (Figure 3)  
OFF  
5.Select the washing time  
Select the washing time according to the  
laundries. (Figure 4)  
WASH TIMER  
Figure 4  
STRONG  
STANDARD  
6.After washing, the buzzer will ring. Set the "WASH  
SELECTOR" at "DRAIN". (Figure 5).  
DRAIN  
WASH SELECTOR  
Figure 5  
9
 
Midway spinning  
1.Put the laundries into the spin tub evenly and smoothly.  
2.Spin  
(1) Put the gland in properly.  
Please put in the gland properly even if the  
laundries quantity is small.  
Push  
Gland  
Push  
Proper  
Proper  
The laundries  
are slanting  
No gland  
(2) Close the inner and outer cover of the spin tub.  
Outer cover of  
The spin tub  
Inner cover of  
The spin tub  
(3) Spin for 1-2 minutes.  
3.Run the foam-removing spinning.  
(1) Open the outer cover of the spin tub.  
(2) Set the water-filling selector control  
rod at the "SPIN" side. Fill water for  
about 1 minute.  
WASH SPIN  
If the water quantity filled is too large,  
the water may flow out from the wash  
tub side. Please twist the water tap to  
limit the water filling.  
(3) Close the outer cover of the spin tub.  
Spin for 1-2 minutes.  
10  
 
Rinsing  
Rinse with water-filling  
OVERFILL  
1.Put the laundries into the wash tub. Select  
suitable current according to the laundries.  
If you find water flo-  
wing out here,please  
twist the water tap to  
limit the water filling.  
2.Adjust the water level  
Set the water level with water level adjusting  
lever according to the laundries quantity.  
Then fill suitable water continuously.  
3.Rinse  
Adjust the wash timer to 5-7 minutes to do  
rinsing.  
(Repeat the midway spinning and  
rinsing with stored water for 2-3 times)  
Rinse with stored water  
1. Put the laundries into the wash tub. Select suitable current according to  
the laundries.  
2. Fill water to preset water level.  
3. Rinse  
Adjust the wash timer to 2-3 minutes to do rinsing.  
When the laundries quantity is below 2.4kg, please use "Standard" current.  
If you use "Strong" current, it may splash.  
11  
 
Spinning  
1. Put the laundries into the spin tub  
evenly and smoothly.  
Selection of the spin time list 3  
Spin time  
Laundries  
(minutes)  
Bed sheet or  
About 4~5  
blanket  
2. Press the gland in the tub properly.  
Close the inner and outer cover of  
the spin tub.  
Underwear  
About 2~4  
(knitwear)  
Swear  
(chemical fiber)  
About 1~2  
3. Spin  
Select suitable spin time according  
to the laundries, and do spinning.  
Blending thin  
Within 1 minute  
laundries  
During spinning, if there's abnormal  
sound, it is generally owing to slanting  
placement of the laundries. Please  
stop the machine and re-order the  
laundries.  
In spinning, it will pause the work if you open the outer cover of the spin  
tub. Close it to resume the spinning.  
To do spinning and draining together,  
please first do spinning for around 1  
minute, then do draining. Otherwise  
the spinning will stop owing to too much  
water stored in the spin tub.  
 
12  
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter and  
overflow filter in time. Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Cleaning the lint filter  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
1. Take off the lint filter  
Put hand at the indicated position.  
Push down to take it off. ( See to  
Figure 1)  
Figure 1  
2. Clean the lint  
Put it in water and clean while it is  
still wet.(See to Figure 2)  
3. Install the lint filter  
After cleaning, insert the bottom  
of the lint filter ( marked with  
"down side") into the overflow filter ,  
then push the upper part of the  
filter in ( marked with " up side ").  
(See to Figure 3)  
Figure 2  
Figure 3  
Cleaning the overflow filter  
Too much lint on the overflow filter will influence  
the normal usage of the machine. Please  
clean it every two months.  
Elastic fixing  
claw  
As indicated in the figure, nip the elastic fixing  
claw and pull it to the direction of the arrow to  
take it off.  
1
Take off the overflow filter.  
13  
 
Cleaning the overflow filter  
2. Take off the corrugation pipe.  
Dismantle the upper part of the  
corrugation pipe inside the  
overflow filter ( as indicated in  
Figure 1).  
Water level  
adjusting lever  
Corrugation  
Pipe  
3. Cleaning the overflow filter  
Clean the lint around the filter  
and flush with tap water.  
Figure 1  
4. Install the overflow filter.  
(1).Install the corrugation pipe.  
(2).Insert the mounting plate at  
the bottom of the filter into  
the valve cover.  
Hook  
(3).Hang up the hook at the left  
upper side.  
(4).Push the upper part in as  
indicated in Figure 2.  
Figure 2  
Disposal of the complete unit  
After washing, dismount the water inlet  
hose.  
Do not store water in the tub for long  
period. Discharge the water immediately  
after each using.  
Pull off the power plug and hang up the  
power cord.  
Hang up the drain hose.  
Wipe the complete unit with soft  
cloth twisted dry.  
Wipe with neutral detergent if too dirty  
Do not wash it directly by water  
Wipe off the water drops on the surface  
and inside the tub with clean soft cloth.  
Open the cover of the wash tub and the  
inner/outer cover of the spin tub for  
some time (about one hour), then close  
them.  
Petrol  
Thinner  
Alcohol  
14  
 
Trouble-shooting Answers to question  
If the laundries fall to the outer side of the spin tub  
If the laundries fall to the outer side of the spin tub,  
please take them out immediately.  
1.Dismantle  
As indicated in the figure, push the point marked  
Spin tub frame  
with " " to pull the spin tub frame to oblique  
upwards to dismantle it.  
2.Install  
After install the back edge of the spin tub frame to  
proper position, push the four points marked with  
"
" by force to reset it.  
Please check carefully. The laundries may fall to the  
lower part of the outer side of the spin tub (as indicated  
in the figure).  
Spin tub  
If the laundries fall to the outer side of the spin tub, during  
spinning the draining will get blocked and the rotation speed  
of the spin tub is reduced.  
Laundries  
When the remained water is frozen  
Prevent the freezing (be sure to discharge the water  
completely after using)  
After complete draining, set the "WASH SELECTOR"  
at "STRONG" or "STANDARD". If it is set at "DRAIN",  
it will be rather difficult for the frozen water to melt.  
Below 50 c  
2~3L  
When the water is frozen  
Pour hot water below 50  
into the wash tub  
to soak it completely. Then turn the pulsator  
with hands gently. Please confirm the drainage  
can work normally before next using.  
15  
 
Trouble-shooting Answers to question  
(If there's breakdown, please pull off the power plug before checking) The following  
phenomena are not breakdowns sometimes. Please confirm again before sending  
it to repair. If there are real breakdowns, please come to the special maintenance  
department or after-sale service department of our company. Do not repair it by yourself.  
Phenomena  
The reason  
Is there power failure?  
Is the power plug loose?  
Is the pulsator twisted by foreign materials?  
The machine does  
not act.  
Is the drain hose put down?  
Is the drain hose frozen?  
Is the drain hose blocked by foreign material?  
The draining dose  
not work  
There's abnormal  
sound during washing  
Are there hair pin, coins or metal items brought  
inside the tub?  
Is the machine slanting?  
Is the gland pressed evenly?  
Are the laundries in spin tub too much?  
There's abnormal  
sound and violent  
vibration during  
spinning  
There may be some  
water flowing out of  
the drain hose in the  
first use of the  
It is the water remained in the factory inspection  
of performance.  
machine.  
16  
 
Packing list  
Quantity  
One piece  
Name  
User's manual  
One piece  
One piece  
Water inlet hose  
Lint filter  
Water-filling jointer  
One piece  
One piece  
One set  
Gland  
Twin-tub washing machine  
Specification  
Type  
Twin-tub washing machine  
Model  
KPB70-113S-P  
Water level Water quantity about  
Rated washing capacity kg  
Rated spinning capacity kg  
Dimension(mm)  
Maximum/55L Medium/46L Minimum/36L  
7.0  
6.0  
L810 W460 H926  
0.02MPa~0.2MPa  
Injection pressure  
17  
 

Graco Radio GTM 11 User Manual
Grizzly Vacuum Cleaner H0602 User Manual
Harbor Freight Tools Battery Charger 45005 User Manual
Harbor Freight Tools Paint Sprayer 43430 User Manual
Harman Kardon Home Theater System HS 250 User Manual
Hasbro Games Venetian Fortune Teller User Manual
Honeywell Door RPWL220A User Manual
Honeywell DVD Player IS4100 User Manual
Hotpoint Range double oven cookers User Manual
HP Hewlett Packard Computer Accessories J8694A User Manual